DeWalt DCS778N Original Instructions Manual
  1. Manuals
  2. Brands
  3. DeWalt Manuals
  4. Saw
  5. DCS778N
  6. Original instructions manual

DeWalt DCS778N Original Instructions Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
DCS7485
Final Page size: A5 (148mm x 210 mm)

Advertisement

Table of Contents
loading

Related Manuals for DeWalt DCS778N

Summary of Contents for DeWalt DCS778N

  • Page 1 DCS7485 Final Page size: A5 (148mm x 210 mm)
  • Page 2 English (original instructions) Copyright D WALT...
  • Page 3 Fig. A...
  • Page 4 Fig. B Fig. C Fig. D...
  • Page 5 Fig. E Fig. F Fig. G Position 2 Position 1 Fig. H Fig. I Position 1 Position 2...
  • Page 6 Fig. J Fig. K Fig. L Fig. M...
  • Page 7 Fig. N Fig. O Fig. P...
  • Page 8 Fig. Q Fig. R...

  • Page 9: Definitions: Safety Guidelines

    English CORDLESS TABLE SAW DCS7485 Congratulations! Fuses: You have chosen a D WALT tool. Years of experience, thorough U.K. & Ireland 230V tools 3 Amperes. in plugs product development and innovation make D WALT one of the EC-Declaration of Conformity most reliable partners for professional power tool users.

  • Page 10: Work Area Safety

    English General Power Tool Safety Warnings non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. WARNING: Read all safety warnings, instructions, c ) Prevent unintentional starting. Ensure the switch illustrations and specifications provided with this is in the off position before connecting to power power tool.
  • Page 11 English g ) Use the power tool, accessories and tool bits etc., b ) Always use saw blade guard, riving knife for every in accordance with these instructions taking into through–cutting operation. For through-cutting account the working conditions and the work to be operations where the saw blade cuts completely through performed.

  • Page 12: Kickback Causes And Related Warnings

    English instructions. This push stick provides sufficient distance workpiece being cut off against the saw blade will create a of the hand from the saw blade. binding condition and kickback. f ) Never use a damaged or cut push stick. A damaged d ) Align the fence to be parallel with the saw blade.

  • Page 13: Additional Safety Rules For Saw Benches

    English e ) The table saw must be secured. A table saw that is not • NEVER attempt to cut a stack of loose pieces of material properly secured may move or tip over. which could cause loss of control or kickback. Support all materials securely.

  • Page 14: Using An Extension Cable

    English Mains Plug Replacement These chargers are not intended for any uses other than • charging D WALT rechargeable batteries. Any other uses (U.K. & Ireland Only) may result in risk of fire, electric shock or electrocution. If a new mains plug needs to be fitted: •...

  • Page 15: Charger Operation

    English Charger Operation exposed. Align the slots on the back of the charger with the exposed screws and fully engage them in the slots. Refer to the indicators below for the charge status of the battery pack. Charger Cleaning Instructions Charge Indicators WARNING: Shock hazard.

  • Page 16: Storage Recommendations

    English Use Mode: When the FLEXVOLT battery stands alone or is in a hammer, stepped on). Electric shock or electrocution may result. Damaged battery packs should be returned to WALT 18V product, it will operate as an 18V battery. When service centre for recycling.

  • Page 17: Battery Type

    English Have defective cords replaced immediately. Wear ear protection. Charge only between 4 ˚C and 40 ˚C. Wear eye protection. Only for indoor use. Wear face mask. Discard the battery pack with due care for Keep hands away from cutting area and the blade. the environment. Charge D WALT battery packs only with designated Carrying point.
  • Page 18 English Mounting the Saw Blade (Fig. A, C) • Young children and the infirm. This appliance is not intended for use by young children or infirm persons WARNING: To reduce the risk of injury, turn unit without supervision. off and disconnect machine from power source •...
  • Page 19 English Fixing to Workbench (Fig. A) 6. Tighten the riving knife lock knob. nOTE: Follow the same procedure for the riving knife. • The machine frame between the feet on each side is WARNING: Before connecting the table saw to the power provided with two holes ...

  • Page 20: Prior To Operation

    English Rail Lock Adjustment (Fig. J, K) 6. Use the small set screws  to adjust the riving knife  33  position. Lay the straight edge on the opposite side of the The rail lock has been factory-set. If you need to re-adjust, blade and repeat adjustments as needed.
  • Page 21 English OPERATION • Lift the red paddle  and push green button  in to turn  41   42  this saw on. Instructions for Use • Push the red button   43  or push down the red paddle to turn this saw off. WARNING: Always observe the safety instructions and applicable regulations.

  • Page 22: Compound Mitre

    English 7. Switch the machine on and allow the blade to reach • During all operations, connect a dust extraction device full speed. designed in accordance with the relevant regulations regarding dust emission. 8. Slowly feed the workpiece underneath the guard, keeping it firmly pressed against the rip fence.

  • Page 23: Optional Accessories

    English BLADE DESCRIPTIONS Application Diameter Teeth Cleaning (Fig. A, R) Construction saw Blades (fast rip) WARNING: Blow dirt and dust out of the main housing General Purpose 210 mm with dry air as often as dirt is seen collecting in and around Fine Crosscuts 210 mm the air vents.
  • Page 24 Belgique et WALT - Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be Luxembourg België Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 enduser.BE@SBDinc.com en Luxemburg 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT Tel: 70 20 15 10 www.dewalt.dk...

This manual is also suitable for:

Dcs7485

Table of Contents