Black+Decker BEW220 Original Instructions Manual page 5

Children should be supervised to ensure that they do not
u
play with the appliance.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any rotating/moving parts.
u
Injuries caused when changing any parts, blades or ac-
u
cessories.
Injuries caused by prolonged use of a tool. When using
u
any tool for prolonged periods ensure you take regular
breaks.
Impairment of hearing.
u
Health hazards caused by breathing dust developed when
u
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured in
accordance with a standard test method provided by EN62841
and may be used for comparing one tool with another. The
declared vibration emission value may also be used in a
preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
The following symbols are shown on the tool, along with the
:
date code:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Electrical safety
#
This tool is double insulated; therefore no
earth wire is required. Always check that the
power supply corresponds to the voltage on
the rating plate.
(Original instructions)
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Dust bag
3. Sanding base
4. Paper clamp lever
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting sanding sheets (fig. A, B, C)
Warning! Never use the tool without a sanding sheet or
accessory in place.
Fitting regular sanding sheets (fig. A, B, C)
Make sure that the tool is switched off and unplugged.
u
Soften the sanding sheet by rubbing its non-abrasive side
u
over the edge of a worktop.
Press the paper clamp levers (4) upwards to release them
u
from the retaining grooves and open the paper clamps by
pressing them down (fig. A).
Place the sheet onto the sanding base (3), making sure
u
that the holes in the sheet line up with the holes in the
base (fig. B).
Insert the edge of the sanding sheet into the front paper
u
clamp as shown (fig. C).
Press the front paper clamp lever (4) downwards and
u
locate it in the retaining groove.
While keeping a slight tension on the sheet, insert the rear
u
edge of the sheet into the rear paper clamp.
Press the rear paper clamp lever (4) downwards and
u
locate it in the retaining groove.
Fitting and removing the dustbag (fig. D)
Fit the dustbag (2) over the dust extraction outlet.
u
Slide the dustbag onto the tool and make sure that it is
u
securely located.
To remove the dustbag, pull it to the rear and off the outlet.
u
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Do not cover the ventilation slots when using the
tool. Make sure that the sanding base is flat on the workpiece.
Switching on and off (fig. E)
To switch the tool on, set the on/off switch (1) to
u
position I.
To switch the tool off, set the on/off switch (1) to
u
position O.
ENGLISH
5