Technical Data; Before Operation - Scheppach bgs 700 Translation From The Original Instruction Manual

6. Technical data

dimensions L x W x H mm
ø grinding wheel mm
grinding wheel thickness mm
ø grinding wheel hole mm
max. circumferential speed m/s
belt speed m/min
grinding /sanding belt L x W
mm
weight kg
drive
rated voltage V/Hz
power rating
idle speed n min
-1
0
Load factor:
A load factor of S2 30 min (intermittent periodic duty)
means that you may operate the motor continuously
at its nominal power level (230 W) for no longer than
30 minutes ON period. If you fail to observe this time
limit the motor will overheat. During the OFF period
the motor will cool again to its starting temperature.
INoise
Sound values were measured in accordance with
EN 61029.
Sound pressure level L
pA
Uncertainty K
pA
Sound power level L
WA
Uncertainty K
WA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Limit the noise to a minimum!
• Only use appliances which are in perfect work-
ing order.
• Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever neces-
sary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
360 x 280 x 335
150
20
12.7
23
895
686 x 50
10.2
230/50
370W S2 30min
2850
82.3 dB(A)
3 dB
91.5 dB(A)
3 dB

7. Before operation

Before you connect the equipment to the mains sup-
ply make sure that the data on the rating plate are
identical to the mains data.
Always pull the power plug before making ad-
justments to the equipment.
• The machine must be set up so that it stands
firmly, i.e. it must be securely screwed to a work
bench or similar.
• The grinder should be fixed permanently at a
suitable place. To attach the grinder to a hard
and flat surface, there are two mounting points
on the grinder. The tool support should be ap-
proximately at the height of your elbow. The
working area is in front of the machine - keep it
free of obstacles.
• All covers and safety devices have to be prop-
erly fitted before the equipment is switched on.
•
It must be possible for the grinding wheel to run
freely.
Assembling the spark deflector (Fig.1-3)
• Slide the spark deflector (2) under the guard
hood (5). Screw the spark deflector (2) to the
guard hood (5) by using the spark deflector
adjustment screw (3).
• Use the spark deflector adjustment screw (3)
with the spring washer and the washer to fix the
spark deflector (2). To secure you will need a
screwdriver (Fig. 2).
• Adjust the spark deflector (2) using the spark
deflector adjusting screw (3) so that the distance
between the dry grinding wheel (6) and the
spark deflector (2) is as small as possible and
certainly does not exceed 2 mm. (Fig.3)
• Adjust the spark deflector (2) periodically to
compensate for wear on the wheel.
Fitting the workpiece supports (Fig. 1/4/5/6)
• Secure the workpiece supports (8) to the
grinder/sander using the workpiece support
star screw (7) on belt side and the 2 fastening
screws for workpiece support (18) on grinding
wheel (5) side.
Adjusting the workpiece supports (Fig. 5+6)
• Adjust the workpiece supports (8) using the
fastening screws for workpiece support (18) and
the workpiece support star screw (7)so that the
distance between the dry grinding wheel (6) or
the grinding/sanding belt (9) and the workpiece
supports (8) is as small as possible and cer-
tainly does not exceed 2 mm.
• Adjust the workpiece supports (8) periodically to
compensate for wear on the dry grinding wheel.
GB
21 / 152