Technical Data; Assembly - Scheppach SM200LB Translation Of Original Instruction Manual

• Do not use any damaged or deformed grinding
wheels or brushes.
• Only use grinding wheels and brushes marked with
a rotational speed which is at least as high as the
speed indicated on the rating plate of the electrical
tool.
• Always leave the brush fastened to the spindle in
order to limit the risk of contact with the rotating
spindle.

6. Technical Data

Delivery
Technical Data
Dimensions L x W x H
Grinding disc max.
Grinding disc min. (after
wear and tear)
Brush max.
Brush min. (after wear)
Grinding disc bore max
Brush bore max.
Brush width
Lamp
Weight
Motor
Motor
Input power S2 10 min
Motor speed
Subject to technical changes!
Load factor:
A load factor of S2 10 min (intermittent periodic duty)
means that you may operate the motor continuously
at its nominal power level (500 W) for no longer than
10 minutes ON period. If you fail to observe this time
limit the motor will overheat. During the OFF period
the motor will cool again to its starting temperature.
Sound and vibration
Sound and vibration values were measured in ac-
cordance with EN 62841.
L sound pressure level
pA
K uncertainty
pA
L sound power level
WA
K uncertainty
WA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three directions)
determined in accordance with EN 62841.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Bench Grinder
SM200LB
User's Manual
390 x 260 x 290 mm
ø 200 mm
ø 150 mm
ø 200 mm
ø 150 mm
ø 16 mm
16 mm
16 mm
LED with battery (2x)
12 kg
230-240 V~ / 50 Hz
500 W
2980 min
-1
62,4 dB(A)
3 dB
77 dB(A)
3 dB
Keep the noise emissions and vibrations to a
minimum.
• Only use appliances which are in perfect working-
order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.

7. Assembly

Before you connect the equipment to the mains sup-
ply make sure that the data on the rating plate are
identical to the mains data.
Always pull the power plug before making adjust-
ments to the equipment.
Pull the power plug before doing any maintenance
or assembly work on the equipment.
• The machine must be set up so that it stands firm-
ly, i.e. it must be securely screwed to a work bench
or similar.
• All covers and safety devices have to be properly
fitted before the equipment is switched on.
• The grinding wheels must rotate freely.
• Check that the voltage on the rating plate is the
same as your supply voltage before you connect
the equipment to the power supply.
Warning! Never connect the plug to power source
outlet until all installations and adjustments are com-
pleted and you have read and understood the safety
and operation instructions.
Tool support (left and right) (Fig. 1, 2, 2.1)
Fasten the tool support (4) to the grinding wheel
guard (6) with the wing screw (a) and washer (b).
The distance between wheel and work rest should
not exceed 2 mm.
Spark guard with LED work lamp (left and right)
(Fig. 1, 3)
Fasten the spark guard (2) with LED work lamps (5)
to the grinding wheel guard (6) with two M5x8 pan
head screws (c).
The distance to the grinding wheel (3) should be not
more than 2 mm. The distance between the spark
guard (2) and the grinding wheel (3) can be adjusted
by slackening the two pan head screws (c). Tighten
the screws securely.
LED work lamp (Fig. 1, 4, 4.1, 4.2)
The lighting (5) can be switched on by pressing the
switch (d) on the lamp. The lighting is switched off
by pressing the switch again.
GB | 21