Minimum Output; Intermediate Outputs - Riello RS 810/M BLU Modulating Operation

6.6.4

Minimum output

Min output must be selected within the firing rate range shown on
Fig. 2 on page 10.
Press button 2)(Fig. 27 on page 23) "Diminishing output" and
keep it pressed until the servomotor regains (Fig. 31 B, page 25)
the adjustment made in the factory: See page 24 and as a con-
sequence adjusting the air damper 5) and the gas butterfly valve
4)(Fig. 30 on page 25).
Adjustment of gas delivery
Progressively adjust the end profile of the mechanical cam I)
Fig. 30 on page 25, using the screws 2).
For example, calibrate the minimum output to 800 kW, check the
emissions and if necessary increase or decrease the opening of
the air damper (See "Air adjustment" on page 25). Bring the out-
put to 800 kW using the screws 2) of the mechanical cam
1)(Fig. 30 on page 25) and check the emissions.
Air adjustment
The regulation of the air is carried out using the angle of the cam
III) of the servomotor (Fig. 28 on page 24) and by using the se-
lector 2)(Fig. 27 on page 23). To adjust the cam of the servomo-
tor, see Fig. 31 A, page 25).
NOTE:
The servomotor follows the adjustment of cam III only when
the angle of the cam is reduced. If it is necessary to increase
the angle of the cam, you must first increase the angle of the
servomotor by means of the "output increase" key, then in-
crease the angle of cam III, and finally bring the servomotor
to the position of MIN output, with the "Output reduction"
key.
To adjust the cam III, see Fig. 31 A and B, page 25.
20163413
Start-up, calibration and operation of the burner
6.6.5

Intermediate outputs

Air adjustment
No adjustment is required
Adjustment of gas delivery
After adjusting the maximum and minimum output of the burner,
carry out air adjustment on higher intermediate positions of the
servomotor. The passage from one position to the next one is ob-
tained by pressing the button 2) on the symbol (+) or (-) (Fig. 27
on page 23). For a brief period press the button 2)(Fig. 27 on
page 23) "Output increase" so that the servomotor rotates by
about 20°, see servomotor graduated index Fig. 31 B, page 25)
and the air damper graduated index 5)(Fig. 30 on page 25).
Screw or unscrew the screw 2) of the mechanical cam (Fig. 30 on
page 25) to increase or decrease the gas output so as to adjust
it to the corresponding air output, to obtain optimal combustion.
Proceed in the same way with the other screws.
Take care that the cam profile variation is progres-
sive.
WARNING
Switch off the burner using the switch 1)(Fig. 27), OFF position,
release the mechanical cam 1)(Fig. 30 on page 25) to separate
the gears of the servomotor, pressing and shifting downwards the
button 3)(Fig. 31 D) and check a few times, by rotating the me-
chanical cam 1)(Fig. 30) manually backwards and forwards, that
the movement is smooth and without any hindrance.
It is recommended that the mechanical cam
1)(Fig. 30 on page 25) be bound again to the ser-
vomotor by shifting button 3)(Fig. 31 C, page 25)
upwards.
WARNING
As far as is possible, try not to move those screws at the ends of
the mechanical cam that were previously adjusted for the open-
ing of the gas butterfly valve to MAX and MIN output.
NOTE:
Once you have finished adjusting the "MAX - MIN - INTER-
MEDIATE" outputs, check ignition once again: noise emis-
sion at this stage must be identical to the following stage of
operation. If you notice any sign of pulsations, reduce the ig-
nition stage delivery.
26 GB