8. Can be used for collecting non-flammable liquids. 9. Dispose of waste in a FIRE SAFE AREA. SOME DUSTS ARE HIGHLY FLAMMABLE OR EXPLOSIVE. LEARN / KNOW WHAT YOU ARE DEALING WITH. FOLLOW ALL LOCAL, STATE, FEDERAL & NFPA CODES AND GUIDE LINES. Oneida Air Systems...
Page 3
Dimensions Nominal dimensions shown. Dimensions subject to slight variations in manufacturing. 19.1" 485 mm 6" 152 mm 6" 152 mm 38" 965 mm 31" 787 mm oneida-air.com...
1/4-20 X 3/4" Hex Head Bolt AFW025000 1/4" Flat Washer AFT000005 1/4" Whiz-Lock Nut Please unpack the parts carefully and confirm you have received each item listed here. You will need the following: • Two 7/16" Wrenches Oneida Air Systems...
Page 6
Use 5/16" drill bit to drill the bolt holes. Note: Use the base of the Cyclone (A) for reference [FIG. 1]. 6" FIG. 1 Oneida Air Systems...
Page 7
Assembly Instructions (Cont.) Apply Gasket (B) around the discharge hole of the Cyclone (A), making sure that the Gasket goes inside the bolt holes and around the inlet hole [FIG. 2]. Note: Make sure ends of Gasket butt together and there are no gaps.
Page 8
Turn Cyclone (A) upside-down and align with the drum lid. Secure to the drum lid with six Hex Bolts (C), twelve Flat Washers (D), and six Whiz-Lock Nuts (E) [FIG. 3]. Note: Thoroughly tighten hardware to eliminate air leaks. FIG. 3 Oneida Air Systems...
Page 9
Assembly Instructions (Cont.) Put Cyclone (A) and lid on top of your dust container and seal it airtight.[FIG. 4]. FIG. 4 oneida-air.com...
Page 10
The Cyclone's inlet is designed to accept crimped ductwork fittings [FIG. 5]. Note: To connect 6" hose to the Super Dust Deputy XL's inlet, Oneida Air Systems offers a specific adapter (#DAO060000) to provide for easier installations. dust collector Tool FIG.
Page 11
The Cyclone's outlets are designed to accept crimped ductwork fittings [FIG. 6]. Note: To connect 6" hose to the Super Dust Deputy XL's outlet, Oneida Air Systems offers a specific adapter (#DAO060000) to provide for easier installations. dust collector Tool FIG.
Page 12
Make sure there are no air leaks at the connections. Review [FIG. 7] on common leak points. Note: Make sure to check your dust drum frequently so you do not overfill it. Leak Point Leak Point Leak Point Leak Point FIG. 7 Oneida Air Systems...
Troubleshooting PROBLEM C AUSE SOLUTION Not separating well. Air leaks in the drum 1. Make sure the lid of the dust drum is in place and well seated. (Only a tiny amount of 2. Check for any damage to the foam seal of the lid. dust should reach the 3.
Page 14
• Ideal for configurations where the drum will be moved around the shop Dust Collector HEPA Cartridge Filter Upgrade Kit #FXK011820 • Upgrade your single-stage dust collector with a retrofit filter that can capture even the finest of dusts Oneida Air Systems...
Page 15
Accessories (Cont.) 17 Gal Steel Drum Kit #SEK170601 • Includes reinforced steel drum, steel lid with pre-cut cyclone mounting holes, and locking- lever ring clamp SDD Cyclone Steel Drum Lid #SEX355506 • Ships with pre-cut holes for installing the Super Dust Deputy cyclones • Ideal for DIYers creating their own dust collection system 35 or 55 Gal.
(if your seal is air-tight) but we recommend using a sealing agent and simple latches for added security [FIG. 8b]. Super Dust Deputy shown with 17 gal. Drum Kit (SXK170601) and Angle Brace Support Kit (AHX000004A). latch FIG. 8a FIG. 8b Oneida Air Systems...
Page 17
Tips and Tricks (Cont.) Mount flex hose to the bottom of the Cyclone instead of mounting the Cyclone directly to the lid. The components you would need to complete this as shown in [FIG. 9a] are: a. (x2) 6" Collared Flange* b.
Page 18
Super Dust Deputy cyclone [FIG. 10b]. Recommended components: i. Square to Round Adapter. Call us at 866-387- 8822 Mon-Friday, 8am-5:30pm EST for help choosing a compatible adapter. ii. Adjustable Elbow (DEA900700) iii. Super Cartridge Filter Retrofit Kit (FXK010039) FIG. 10a FIG. 10b Oneida Air Systems...
Page 19
• All commercial codes require metal pipe for wood dust. Oneida Air Systems offers metal pipe, as do all dust collection experts in the industry. Metal pipe is used because it provides substantially better performance, and proper fittings are readily available [FIG.
Page 20
Unlike Oneida Air Systems, other manufacturers do not provide real-world airflow performance data. Without that information, we cannot reliably size a ducting system for those dust collectors.
Page 21
Tips and Tricks (Cont.) To dust collector Tool FIG. 12a Tool 90 deg. tee vs. 45 deg. wye Short radius vs. long radius FIG. 12b FIG. 12c oneida-air.com...
Woodworking Magazine. • Compact, lightweight system. Supercell 14 Gal. High -Pressure Dust Collector #XSK000014 • 10x higher suction power than standard dust collectors • Excels at collecting dust from all tools with 1" to 5" dia. ports Oneida Air Systems...
Limited Warranty – Activate online at oneida-air.com/warranty Oneida Air Systems®, Inc. (OAS) warrants the products it manufactures for a period of 1 or more years, depending on the product, to the original purchaser from the date of purchase, unless otherwise specified. Items not manufactured by Oneida Air Systems are limited to their own manufacturer’s warranties.
Page 24
Regardless of where you purchased your system, if you have any questions or issues with missing / damaged parts, please call Oneida Air Systems first to let us help resolve your problem. We fully stand behind the quality of our products and place the utmost value on the satisfaction of our customers.