Related Manuals for Oneida Air Systems Dust Deputy 2.5 D.I.Y.
Summary of Contents for Oneida Air Systems Dust Deputy 2.5 D.I.Y.
- Page 1 Dust Deputy 2.5 D.I.Y. Dust Deputy 2.5 Plus Cyclone Separator #AXD251004 #AXD250504 U.S. Pat. RE40048 7282074 Appearance may vary slightly Rev: 03/08/2022 Doc. # ZBM000061...
-
Page 2: Safety Practices
8. Can be used for collecting non-flammable liquids. 9. Dispose of waste in a FIRE SAFE AREA. SOME DUSTS ARE HIGHLY FLAMMABLE OR Ÿ EXPLOSIVE. LEARN/KNOW WHAT YOU ARE DEALING WITH. FOLLOW ALL LOCAL, STATE, FEDERAL & NFPA CODES AND GUIDELINES. Oneida Air Systems... -
Page 3: System Dimensions
System Dimensions Nominal dimensions shown. Dimensions subject to slight variations in manufacturing. 2-1/4" I.D. 57 mm 7-5/8" 194 mm 8-1/2" 216 mm 2-1/2" O.D. 64 mm 2-1/4" I.D. 57 mm 15-5/8" 397 mm 13-3/4" 349 mm oneida-air.com... -
Page 4: System Contents
Note: Due to a variety of factors associated with the molding process, the base of the Dust Deputy 2.5 cyclone may appear warped rather than perfectly flat. This is normal and does not impact performance as long as the cyclone is installed according to these instructions. Oneida Air Systems... - Page 5 System Contents (Cont.) Note: Use a 5-gallon bucket with Lid (E) or a suitable drum/ container with your own supplied lid. Your container must be able to withstand vacuum pressure, otherwise it may collapse when in use. We recommend a minimum 90 mil wall thickness. The larger the container, the sturdier the walls must be to prevent collapse.
- Page 6 Gasket (B) and align all the holes. Secure Cyclone (A), Gasket (B) and lid together using six Bolts (C1), six Washers (C2), and six Whiz-Lock Nuts (C3) as shown in [FIG. 2]. Note: Tighten hardware evenly to eliminate air leaks. FIG. 2 Oneida Air Systems...
- Page 7 Assembly Instructions For the 2.5 D.I.Y (#AXD251004), continue to Step 4. Turn Cyclone (A) upside-down. Place Gasket (B) on the base of Cyclone and align all the holes. Place the topside of the Lid (E) against Gasket and align all holes. Secure Cyclone, Gasket and Lid together using six Bolts (C1), six Washers (C2), and six Whiz-Lock Nuts (C3) as shown in [FIG.
- Page 8 To empty the bucket, lift up on the Lid’s latch and pull up on the Lid to release the Lid/ Cyclone assembly from the bucket [FIG. 4c]. FIG. 4a FIG. 4b FIG. 4c Oneida Air Systems...
- Page 9 Assembly Instructions (Cont.) Connect Cyclone's (A) inlet (sideways facing port) to your dust producing tool with your hose or ductwork. Connect the Cyclone's (A) outlet (top port) to your vacuum with the provided hose, your hose, or ductwork [FIG 5]. Both inlet and outlet accept standard 2.5"...
- Page 10 Note: Any air leak in the lid or drum will affect separation performance. Make sure to check your dust drum frequently so you do not overfill it. Leak Point Leak Point Leak Point Leak Point FIG. 6 Oneida Air Systems...
- Page 11 Adding Cyclones to Improve Performance Attach in Series To Tools Increases particle separation efficiency, especially with very fine dust. Top View Attach in Parallel To Tools To Tools Increases CFM. Top View 200 CFM +100 CFM +100 CFM Attach Multiple Vacuums More CFM/airflow to larger tools such as table saw,...
- Page 12 For mobility and additional stability, you can make a plywood platform to fasten your bucket to. We recommend 5 casters for the best stability. FIG. 7 Oneida Air Systems...
-
Page 13: Troubleshooting
Troubleshooting PROBLEM C AUSE SOLUTION Not separating well. Air leaks in the 1. Check for leaks between the lid and the (Only a tiny amount drum. dust drum. of dust should reach 2. Check for holes or leaks in the dust drum. the vacuum). - Page 14 LID MOUNTING TEMPLATE Dust Deputy Template FOR STANDARD 14" TALL DUST DEPUTY CYCLONES Use this template to prepare your lid for installation of the Dust Deputy 2.5 D.I.Y. 1:1 SCALE. DO NOT ALTER DOCUMENT SIZE WHEN PRINTING Oneida Air Systems...
-
Page 15: Warranty Information
Limited Warranty – Activate online at oneida-air.com/warranty Oneida Air Systems, Inc. (OAS) warrants the Dust Deputy 2.5 D.I.Y. and 2.5 Plus for a period of 1 year to the original purchaser from the date of purchase, unless otherwise specified. Items not manufactured by Oneida Air Systems are limited to their own manufacturer’s warranties. - Page 16 Regardless of where you purchased your Oneida Air Systems' product, if you have any questions or issues with missing / damaged parts, please call Oneida Air Systems first to let us help resolve your problem. We fully stand behind the quality of our products and place the utmost value on the satisfaction of our customers.