Page 1
UP Squared 6000 Edge Edge System UPN-EDGE-EHL01 User’s Manual 1 Last Updated: February 8, 2022...
Page 2
AAEON assumes no liabilities resulting from errors or omissions in this document, or from the use of the information contained herein. AAEON reserves the right to make changes in the product design without notice to its users.
Page 3
Acknowledgement All other products’ name or trademarks are properties of their respective owners. Microsoft® , Windows® are registered trademarks of Microsoft Corp. Intel® , Pentium® , and Celeron® are registered trademarks of Intel Corporation Intel Atom™ is a trademark of Intel Corporation ...
Page 4
Packing List Before setting up your product, please make sure the following items have been shipped: Item Quantity UPN-EDGE-EHL01 with heatsink (UP Squared 6000 Edge) Quick Start Guide 40Pin Phoenix Connector If any of these items are missing or damaged, please contact your distributor or sales representative immediately.
Page 5
(if any), its specifications, dimensions, jumper/connector settings/definitions, and driver installation instructions (if any), to facilitate users in setting up their product. Users may refer to the product page at AAEON.com for the latest version of this document. Preface...
Page 6
Safety Precautions Please read the following safety instructions carefully. It is advised that you keep this manual for future references All cautions and warnings on the device should be noted. Make sure the power source matches the power rating of the device. Position the power cord so that people cannot step on it.
Page 7
If any of the following situations arises, please the contact our service personnel: Damaged power cord or plug Liquid intrusion to the device iii. Exposure to moisture Device is not working as expected or in a manner as described in this manual The device is dropped or damaged Any obvious signs of damage displayed on the device...
Page 8
FCC Statement This device complies with Part 15 FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation.
Page 10
China RoHS Requirement (EN) Poisonous or Hazardous Substances or Elements in Products AAEON Main Board/ Daughter Board/ Backplane Poisonous or Hazardous Substances or Elements Hexavalent Polybrominated Polybrominated Component Lead Mercury Cadmium Chromium Biphenyls Diphenyl Ethers (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) PCB &...
Specifications System Intel® Atom® X6413E / X6425RE, Celeron® N6210 (no PSE), Pentium® J6426 Processor SoC Memory Onboard DDR4, Max 8GB Single Channel: 2 GB Dual Channel: 4 GB, 8 GB Graphics Intel® UHD Graphics Storage Onboard eMMC 32G/64G Optional with M.2 2280 M-key x 1, SATA3 x 1 Ethernet GbE x 1, 2.5GbE x 1 Atom: Intel®...
Page 15
I/O Placements Power DC-in Jack x 1, Power Button x 1 USB 3.2 Gen 2 Type A x 2 USB 3.2 Gen 2 Type C (support OTG) x 1 (Limited to Atom series) Display Port HDMI 2.0b x 1 DP 1.2 x 1 Ethernet RJ45 x 2 RS232/RS422 x 1 (Limited to Atom series)
List of Jumpers and Connectors Please refer to the table below for all of the board’s jumpers that you can configure for your application Label Function PWR button CN28 CN35 M.2 Key-B Slot CN36 M.2 Key-E Slot CN38 USB Type A DUAL PORT CN39 SATA CONN CN40...
Signal Signal Signal PLT_RST#(1.8V) +3.3V +3.3V +3.3V 2.3.4 M.2 Key-E Slot (CN36) Signal Signal Signal +3.3V USB2_D+ +3.3V USB2_D- CNV_BRI_RSP CNV_RGI_DT CNV_RGI_RSP PCIE_TXP CNV_BRI_DT Chapter 2 – Hardware Information...
Signal Signal Signal PCIE_TXN PCIE_RXP PCIE_RXN PCIE_CLKP PCIE_CLKN SUS_CLK WIFI_RST# PCIE_CLKREQ# BT_EN PCIE_WAKE# WIFI_EN +3.3V +3.3V 2.3.5 USB Type A DUAL PORT (CN38) Signal Signal Signal USB2_D1- USB2_D1+ USB3_RX1- USB3_RX1+ USB3_TX1- USB3_TX1+ USB2_D2- USB2_D2+ USB3_RX2- USB3_RX2+ Chapter 2 – Hardware Information...
Signal Signal Signal USB3_TX2- USB3_TX2+ 2.3.6 SATA CONN (CN39) Signal Signal SATA_TXP0 SATA_TXN0 SATA_RXN0 SATA_RXP0 2.3.7 SATA POWER (CN40) Signal Signal +V5S Chapter 2 – Hardware Information...
2.3.12 USB2.0/ UART 1x10P Wafer (CN49) Signal Signal Signal USB2_D5- USB2_D5+ USB2_D6- USB2_D6+ UART_RX UART_TX 2.3.13 DC Jack (CN50) Signal Signal Signal DC_IN 2.3.14 eDP (CN55) Chapter 2 – Hardware Information...
Signal Signal 2.3.18 RS232/ 422 (CN62) Signal Signal CTS/RX- RTS/TX+ TX/TX- RX/RX+ Cable Signal Signal RX/RS422TX- TX/RS422TX+ RTS/RS422RX+ CTS/RS422RX- Chapter 2 – Hardware Information...
2.3.19 SWD (CN64) Signal Signal DBRESET PSE_SWDIO PSE_SWCLK PSE_TRACESWO PSE_TRACECLK PSE_TRACEDATA_0 PSE_TRACEDATA_1 PSE_TRACEDATA_2 PSE_TRACEDATA_3 2.3.20 Front Panel (CN65) Signal Signal RESET POWER S/W Chapter 2 – Hardware Information...
2.3.21 AUDIO (CN66) Signal Signal LOUT_R LOUT_L +V5S_AUD AUDIO-JD MIC_IN_JD 2.3.22 FAN (J1) Signal Signal FAN_TAC FAN_CTL Chapter 2 – Hardware Information...
Linux Setup UPN-EDGE-EHL01 supports Linux operating systems (see Chapter 1 for specifications). For instructions on how to install a Linux OS onto your UPN-EDGE-EHL01, you can find several guides and tutorials in the wiki section of the UP Board website at https://up-board.org...
Unknown Device Troubleshooting After installing Windows drivers on UP Squared 6000 (UPN-EHL01), you will see some unknown devices shown on device manager. Most unknown devices can be fixed by manually installing the driver from the Intel Serial IO 5.123.1.1023, except for Multimedia Audio Controller but here’s how to fix it: Multimedia Audio Controller To fix the yellow exclamation mark “Multimedia Audio Controller”, please go to BIOS...
Page 45
VEN_AANT&DEV_1280: This is the ADC for Linux, there is no Windows driver. This can be ignored. Chapter 3 – Drivers Installation...
Introduction This section provides instructions for the installation of the UP Framework SDK. Instructions are provided for Windows 10 and Windows IoT Core. You can download the latest version of UP Framework SDK from the UP community: https://downloads.up-community.org/download/up-sdk-for-windows-10-and-windows-iot/ A.2 Installation for Windows 10 Step 1 Locate the downloaded file UpFrameworkSetup.msi and run the installer.
Page 48
Step 2 Select the installation folder. Default destination path is C:\Program Files(x86)\AAEON\ You may also choose to install the UP Framework SDK for all users or only the current user. Press “Next” to continue installation. Step 3 Press “Next” to confirm the installation.
Page 49
Step 4 Press “Close” to exit once setup is complete. Appendix A – UP Framework SDK Installation...
A.3 Installation for Windows IoT Core Before you begin, make sure you have downloaded and installed the latest version of the Windows IoT Core image from the UP community. Installation requires using a connected PC with the UP Framework SDK software downloaded and saved.
Page 51
Step 2 Download the UP Framework SDK to your PC and unzip the files. Open PowerShell as an Administrator. Run the command RemoteInstallation.ps1 to install the UP Framework SDK. Enter the IP address of the UP IoT Core device when prompted. Appendix A –...
Cables and Connectors This table provides detailed information about the cables and connectors used by the UP Squared 6000 Edge (UPN-EDGE-EHL01). If you have any questions about the configuration of your board, please contact your AAEON sales representative. Mating Loca-...