Subscribe to Our Youtube Channel
Related Manuals for Intec Cyclone
Summary of Contents for Intec Cyclone
- Page 1 Cyclone Instruction Manual Insulation blowing machine Intec — 9251 Bruin Boulevard, Frederick, CO 80504 USA T: 303-833-6644 Web: www.inteccorp.com Email: info@inteccorp.com Rev Date: 20211203...
- Page 2 We take pride in making your job as easy and profitable as possible. The right system for your needs: Intec strives to provide you with the best combination of portability, functionality, and installation versatility to surpass your desired success. From lightweight...
-
Page 3: Table Of Contents
Cyclone Instruction Manual Table of Contents INTRODUCTION ................... 1 SYMBOLS ....................3 SAFETY FIRST ....................3 HOW THE SYSTEM WORKS ................. 4 MAINTENANCE ..................... 7 TROUBLESHOOTING ..................8 SPECIFICATIONS ................... 10 ELECTRICAL DRAWING ..................13 MAKING A CLAIM FOR DAMAGE OR LOSS ............... 14 WARRANTY .................... -
Page 4: Symbols
Cyclone Instruction Manual Symbols SYMBOL SYMBOL MEANING Indicates an imminently hazardous situation, which, if not avoided, Danger will result in death or serious injury. Indicates a potentially hazardous situation, which, if not avoided, Warning could result in death or serious injury. -
Page 5: How The System Works
Cyclone Instruction Manual How the System Works OVERVIEW: The cellulose insulation is loaded into the hopper. The agitator breaks-up and conditions the insulation for proper density while also sweeping the insulation into the airlock. The airlock transports the insulation into the airstream created by the blower system. Insulation is discharged from the airlock into the hose. - Page 6 Cyclone Instruction Manual Set up and Operation System Set up: Set system on a dry, level surface. Obtain appropriate protective equipment. Attach hose to machine outlet using a hose clamp. Open slide gate. Connect the wired remote to the wired remote receptacle on the control panel.
- Page 7 Cyclone Instruction Manual System Operation: Activate System a. Turn the BLOWER control to the ON position. b. Turn the AGITATOR control to the ON position. c. Use blower and agitator controls on the remote to operate system. Notes: With all switches – both control panel and remote -- in...
-
Page 8: Maintenance
Replace airlock seals if a cut or tear is evident. Airlock seals should be replaced every 300 hours of operation, or once per year. Visit www.inteccorp.com or contact Intec for replacement instructions. Chain Clean and lubricate the chain once per year. -
Page 9: Troubleshooting
Cyclone Instruction Manual Trouble Shooting Problem Likely Cause Remedy Machine does not run. Power cord connection is loose. Ensure appropriate power cord connection at machine. Ensure appropriate power cord connection at power source. Power cord not connected at Connect power cord. - Page 10 Cyclone Instruction Manual Problem Likely Cause Remedy Insulation exiting hose is Heavy insulation material. Push slide gate in 1-2 holes. dribbling out. Kink in hose. Straighten hose. Airlock seal is worn. Inspect airlock seals for cuts and wear. Have a qualified technician replace airlock seals.
-
Page 11: Specifications
Cyclone Instruction Manual Specifications Weight 69kg 152 lbs Blower 2.8 m /min, 230VAC 4.9 amp 104 CFM, 115VAC, 8 amp Drive Motor 0.37kW, 230VAC, 4.1 amp ½ HP, 115VAC, 7.8 amp Power Requirements 230VAC, 50Hz, 8 amp circuit 115VAC, 60 Hz, 15 amp circuit T: 303-833-6644 www.inteccorp.com... -
Page 12: Electrical Drawing
Cyclone Instruction Manual Electrical Drawing T: 303-833-6644 www.inteccorp.com Original Language - English... -
Page 13: Making A Claim For Damage Or Loss
Cyclone Instruction Manual Making a Claim for Damage or Loss Your Intec products were carefully packed and thoroughly inspected before leaving our factory. We understand that damage to or defects with your system may unfortunately occur. Please inspect your shipment carefully upon arrival and save the shipping containers and packaging materials in case of damage. -
Page 14: Warranty
It is expressly understood and agreed that no officer, agent, salesman or employee of the manufacturer Intec (MANUFACTURER) has the authority to obligate the MANUFACTURER by any terms, stipulations, or conditions not herein expressed; that all previous representations and agreements, either verbal or written, referring to the machinery and equipment, which is the subject of this Warranty, are hereby superseded and canceled, and that there are no promises or agreements outside of the Warranty agreement.
Need help?
Do you have a question about the Cyclone and is the answer not in the manual?
Questions and answers