Related Manuals for DTK PRM-0076I
Summary of Contents for DTK PRM-0076I
- Page 1 PRM-0076I High Performance Pentium II PCI Mainboard Edition 3.10 1998 DTK Computer, Inc.
- Page 2 WARNING For the system to operate normally, please make sure J6 of the mainboard is set as below. Refer to Fig. 2 in this manual for the location J6. If J6 is shorted to 2-3, no CMOS data can be retained. CAUTION The motherboard is an electrostatic sensitive device.
-
Page 3: Table Of Contents
CONTENTS CHAPTER 1 INTRODUCTION CHAPTER 2 JUMPER SETTINGS JUMPERS PRESENTATION GRAPHICAL DESCRIPTION OF JUMPER SETTINGS CPU SPEED J6 - CLEAR CMOS DATA J2 - VOLTAGE SELECTION FOR SYSTEM ROM MEMORY CONFIGUARTION CHAPTER 3 CONNECTOR CONFIGURATION JP1 - IrDA CONNECTOR JP8 - ATX POWER SUPPLY CONNECTOR JP9 - SLOT 1 FOR PENTIUM II CPU JP10 - FLOPPY DRIVE CONTROLLER JP11, JP12 –... - Page 4 4.13 SAVE & EXIT SETUP MENU 4.14 EXIT WITHOUT SAVING MENU CHAPTER 5 FLASH AND DMI UTILITY AWARD FLASH UTILITY DESKTOP MANAGEMENT INTERFACE (DMI) OVERVIEW APPENDIX A QUICK GUIDE...
-
Page 5: Introduction
CHAPTER 1 INTRODUCTION Preface The motherboard is a 4 layer, ATX form factor high performance PCI/AGP mainboard. It includes Intel i82440LX system chipset, Winbond W83977TF Super I/O controller. Features Processor • Intel Pentium II series. • The mainboard can run with following speeds: 233, 266, 300 and 333MHz Chipset •... - Page 6 Chapter 1 System BIOS • Award BIOS (128KB Flash EPROM). Slots • One AGP slot • Four PCI slots • Two ISA slots Form Factor • ATX Form Factor Size (305mm x 180mm) 4 Layer Fig. 1 Key Components of the Mainboard...
-
Page 7: Jumper Settings
CHAPTER 2 JUMPER SETTINGS JUMPERS PRESENTATION Pins 1 and 2 are shorted with a jumper cap. Pins 2 and 3 are shorted with a jumper cap. The jumper is shorted when the jumper cap is placed over the two pins of the jumper. The jumper is open when the jumper cap is removed from jumper. -
Page 8: Graphical Description Of Jumper Settings
Chapter 2 GRAPHICAL DESCRIPTION OF JUMPER SETTINGS Fig. 2 Jumper Location of the mainboard... -
Page 9: Cpu Speed
Jumper Settings CPU SPEED The table below summaries the CPU frequence and settings of each jumper of the motherboard. CPU Type Freq. Ratio Bus Freq. Rating Setting Pentium II 233MHz 3.5x 1-2 open 3-4 open 5-6 close Pentium II/ 266MHz 4.0x 1-2 close Celeron... -
Page 10: J2 - Voltage Selection For System Rom
Chapter 2 J2 - VOLTAGE SELECTION FOR SYSTEM ROM J2 is used to select the operation voltage of the system ROM. Table 3: Voltage Selection for System ROM MEMORY CONFIGUARTION The mainboard lets user upgrade system memory via DIMM sockets on the mainboard. -
Page 11: Connector Configuration
CHAPTER 3 CONNECTOR CONFIGURATION Once the mainboard has been fastened into system case, the next step is to connect the internal cables. The internal cables are wire leads with plastic female connectors that attach to the connectors. The mainboard connectors have varying numbers of pins and are the points of contact between the mainboard and other parts of the computer. -
Page 12: Jp1 - Irda Connector
Chapter 3 JP1 - IrDA CONNECTOR JP1 is a IrDA connector that use UART2 as interface of IrDA Infrared and ASKIR. Fig. 4 IrDA Connector JP8 - ATX POWER SUPPLY CONNECTOR Fig. 5 ATX Power Supply Connector JP9 - SLOT 1 FOR PENTIUM II CPU JP8 is the slot for Pentium II CPU. -
Page 13: Jp10 - Floppy Drive Controller
Connector Configuration JP10 - FLOPPY DRIVE CONTROLLER This connector supports the floppy drive ribbon cable. After connecting the single end to the board, connect the two plugs on the other end to the floppy drive. JP11, JP12 – SECONDARY/PRIMARY IDE CONNECTORS These connectors support the provided IDE hard disk ribbon cable. -
Page 14: Jp15 - Power Led
Chapter 3 JP15 - POWER LED Attach the power led cable to this connector. If the system is power on, the indicator lights. Fig. 8 Power LED JP16 - RESET Attach the Reset switch cable to this connector. The Reset switch restarts the system. -
Page 15: Ps/2 Keyboard Connector
Connector Configuration Fig. 10 I/O Connector 3.13 PS/2 KEYBOARD CONNECTOR This connector is a six-pin female mini DIN connector using a PS/2 plug. If a standard AT size keyboard plugs, you may use the DIN to mini DIN adaptor. 3.14 PS/2 MOUSE CONNECTOR This connector is a six-pin female mini DIN connector using a PS/2 plug. -
Page 16: Retention Mechanism Kits Installation Guide
Chapter 3 3.18 RETENTION MECHANISM KITS INSTALLATION GUIDE Retention Mechanism Kits includes following components: Retention mechanism Assembly Fig. 11 Retention Mechanism Attach Mount Fig. 12... - Page 17 Connector Configuration Before the installation of RM Kits find the six holes on the motherboard for RM installation. The hole position and usage is as following: Fig. 13 Installation Guide Mount the two RM Attach Mounts onto the motherboard from bottom side. These mounts will be used to attach the RM Assembly.
-
Page 18: Optional Heatsink Support Installation Guide
Chapter 3 Please refer to the diagram for the installation of Celeron CPU or Pentium II in SECC2 package. Fig. 15 3.19 OPTIONAL HEATSINK SUPPORT INSTALLATION GUIDE Optional Heatsink Support includes following components: Heatsink Top Support Fig. 16... - Page 19 Connector Configuration Heatsink Support Base Fig. 17 Installation Guide Refer to Fig. 13, install the Heatsink Support Base onto the motherboard, insert the two plastic nail to the hole in the Heatsink Support Base as following diagram: Fig. 18...
- Page 20 Chapter 3 Insert the Heatsink Top Support to the Pentium II Heatsink and the Heatsink Support Base as the following diagram: Fig. 19...
-
Page 21: Award Bios Setup Guide
CHAPTER 4 AWARD BIOS SETUP GUIDE This following manual is specially provided for the BIOS supported system. After the configuration of the mainboard, and have assembled the components, user can turn on the completed system. At this point, run the software setup to ensure that the system information is correct. - Page 22 Chapter 4 Press the <DEL> key to enter the AWARD BIOS setup program and the following screen appears: ROM PCI/ISA BIOS (2A69JD1C) CMOS SETUP UTILITY AWARD SOFTWARE, INC. STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP USER PASSWORD POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION...
-
Page 23: Standard Cmos Setup
Award BIOS Setup Guide STANDARD CMOS SETUP ROM PCI/ISA BIOS (2A69JD1C) STANDARD CMOS SETUP AWARD SOFTWARE, INC. Date (mm:dd:yy) : Wed, May 21 1997 Time (hh:mm:ss) : 20 : 27 : 55 HARD DISKS TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE Primary Master : Auto AUTO... -
Page 24: Bios Features Setup
Chapter 4 BIOS FEATURES SETUP ROM PCI/ISA BIOS (2A69JD1C) BIOS FEATURES SETUP AWARD SOFTWARE, INC. Virus Warning : Enabled Video BIOS Shadow : Disabled CPU Internal Cache : Disabled C8000-CBFFF Shadow : Disabled External Cache : Disabled CC000-CFFFF Shadow : Disabled Quick Power On Self Test : Disabled D0000-D3FFF Shadow... - Page 25 Award BIOS Setup Guide Boot Sequence: With the default setting the BIOS first attempts to boot from drive A: and then, if unsuccessful, from hard disk C:. User can select other boot up sequence. Available sequences are “A,C,SCSI”, “C,A,SCSI”, “C,CDROM,A”, “CDROM,C,A”, “D,A,SCSI”, “E,A,SCSI”, “F,A,SCSI”, “SCSI,A,C”, “SCSI,C,A”, “C only”, “LS120,C”.
-
Page 26: Chipset Features Setup
Chapter 4 Report No FDD For WIN 95: Choose Yes or No. Yes will show a removable disk in Windows 95 when the floppy drive is set as None. Video BIOS Shadow: ROM Shadow copies Video BIOS code from slower ROM to faster RAM. Video BIOS can then execute from RAM. - Page 27 Award BIOS Setup Guide A short description of the screen items follows: Auto Configuration: When Auto Configuration is Enabled, BIOS will sets the CPU Clock according to CPU speed. Otherwise, set it manually. DRAM Speed Selection: Choose 60ns or 70ns according to the DRAM SIMM Module on the motherboard.
-
Page 28: Power Management Setup Menu
Chapter 4 Current CPU FAN Speed: This item will show the rotate speed per minute of the CPU FAN connected to FAN1. Current SYSTEM FAN1 Speed: This item will show the rotate speed per minute of the SYSTEM FAN connected to FAN2. Current SYSTEM FAN2 Speed: This item will show the rotate speed per minute of the SYSTEM FAN connected to FAN3. - Page 29 Award BIOS Setup Guide Power Management: Available selection are “Disabled”, “User Define”, “Max Saving” and “Disabled” will disable all the power saving functions. “User Define” makes the time period waiting for Suspend Mode to be programmed. “Max Saving” will set the time period waiting for Suspend Mode to be 20 seconds. “Min Saving”...
-
Page 30: Pci Configuration
Chapter 4 Reload Global Timer Event: When Enabled, an event occurring on each device listed below restarts the global time for Standby Mode. IRQ[3-7,9-15], NMI Primary IDE 0 Primary IDE 1 Secondary IDE 0 Secondary IDE 1 Floppy Disk Serial Port Parallel Port PCI CONFIGURATION The PCI Configuration Setup option is used to configure the PCI add-on Cards on PCI... - Page 31 Award BIOS Setup Guide A short description of the screen items follows: PNP OS Installed: Set this option to Yes if the operating system installed in the computer is Plug and Play-aware (e.g. Windows 95). Resources Controlled By: The Award Plug and Play BIOS can automatically configure all the boot and Plug and Play compatible device.
-
Page 32: Integrated Peripherals Setup Menu
Chapter 4 INTEGRATED PERIPHERALS SETUP MENU The Integrated Peripherals setup option is need to change the values of the I/O chipset registers for I/O functions. ROM PCI/ISA BIOS (2A69JD1C) INTEGRATED PERIPHERALS AWARD SOFTWARE, INC. IDE HDD Block Mode : Enabled Onboard Parallel Port : 378/IRQ7 IDE Primary Master PIO... - Page 33 Award BIOS Setup Guide IDE Primary Master UDMA/IDE Primary Slave UDMA/IDE Secondary Master UDMA/IDE Secondary Slave UDMA: Available selection are “Auto” or “Disabled”. To choose “Auto”, the system BIOS will scan the IDE device and decide Ultra DMA supported or not.
-
Page 34: Load Setup Defaults Menu
Chapter 4 LOAD SETUP DEFAULTS MENU This Main Menu item uses the default setup values. Use this option as a diagnostic aid if the system behaves erratically. Choose this item and the following message appears: “ L oad SETUP Defaults (Y/N)? N” To use the Power-On defaults, change the prompt to “Y”... -
Page 35: Ide Hdd Auto Detection
Award BIOS Setup Guide 4.11 IDE HDD AUTO DETECTION When users can not find the Hard Disk information, it is very helpful to use this option. Choose this item and press <Enter>. After couple seconds, the screen will appear the Hard Disk information and following message: “... - Page 36 CHAPTER 5 FLASH AND DMI UTILITY AWARD FLASH UTILITY This section will provide instructions to guide you through updating your old BIOS. The file name we use to program here is test.bin, and the file name to save old BIOS is 2A59F000.OLD.
- Page 37 Flash and DMI Utility If you do not wish to save the old BIOS: Please type “N”, and then press the ENTER key. Then you will be request to answer: “Are You Sure to Program?” Answer “N” if you do not want to program, and then it will exit. To save the old BIOS: Please respond “Y”, and then press the ENTER key.
- Page 38 Chapter 5 DESKTOP MANAGEMENT INTERFACE (DMI) OVERVIEW This motherboard can support DMI within the BIOS level. DMI is able to auto- detect and record information pertinent to a computer’s system such as the CPU type, CPU speed, and internal/external frequencies, and memory size. The onboard BIOS will detect as many system information as possible and store those collected information in a 4KB block in the motherboard’s flash EPROM and allow the DMI to retrieve data from this database.
- Page 39 Flash and DMI Utility Use the ←→ (left-right) cursors to move the top menu items and the ↑↓ (up-down) cursor to move between the left hand menu items. The bottom of the screen will show the available keys for each screen. Press enter at the menu item to enter the right hand screen for editing. “Edit component”...
- Page 40 Chapter 5 Load DMI File You can load the disk file to memory by entering a drive and path and file name here.
- Page 41 Flash and DMI Utility Save DMI File You can save the DMI (normally only saved to flash ROM) to a file by entering the drive and path here. If you want to cancel save, you may press ESC and a message “Bad File Name” appears here to show it was not saved.
- Page 42 APPENDIX A QUICK GUIDE The table below summaries the functions and settings of each jumper of the motherboard. Function Jumper Settings CPU Speed Pentium II 233MHz 1-2 open 3-4 open Selection 5-6 close Pentium II/Celeron 266MHz 1-2 close 3-4 close 5-6 open Pentium II/Celeron 300MHz 1-2 open...