Advertisement
Quick Links
CAUTION: Do not smoke inside the cab or expose the enclosure to direct flames. Product is FLAMMABLE.
Be sure to read these instructions thoroughly before opening and installing the enclosure. The installation is
best done when the temperature is 70 degrees F. or warmer. The temperature affects the adhesive Velcro, if
conditions prevent installing in warmer weather it helps to store the adhesive Velcro at room temperature
prior to installation.
1. Carefully open the carton and remove the rolled-up Cab Enclosure on a large flat surface that is clean
and free of dirt or other material that may soil or scratch the windows of the Cab.
2. This cab enclosure is made up of 4 different panels that all come together to fully enclose the vehicle.
You may put on different pieces or leave other pieces off to create the enclosure that best meets your
needs.
3. Check over the parts included in the carton with the parts list shown below:
Velcro Hook strips--------------4 each---------12" long
"
"
"
Webbing with Velcro-----------4 each
Webbing with Grommets------2 each
Snap studs----------------------14 each (2 extra)
Door Panels----------------------2 each
Rear Window--------------------1 each
If any parts are damaged or missing please contact customer service at (606) 845-7439.
4. For these instructions we will be installing the entire enclosure. This will cover every piece so if you
should want to install just parts of the enclosure these instructions should be sufficient. The order of
installation will be as follows:
a. Side Door Panels
b. Rear Window
c. Top Panel
2515 Bypass Rd. Flemingsburg, KY 41041
Instructions for Installation and Care of Can-Am Maverick
Full Cab Enclosure fits Polycarbonate
CA-MAVERICK-FC05
"------------------------16 each----------3" long
"-------------------------6 each----------6" long
"-------------------------2 each----------8" long
606-845-7439
Advertisement
Related Manuals for FALCON RIDGE Can-Am Maverick
Summary of Contents for FALCON RIDGE Can-Am Maverick
- Page 1 2515 Bypass Rd. Flemingsburg, KY 41041 606-845-7439 Instructions for Installation and Care of Can-Am Maverick Full Cab Enclosure fits Polycarbonate CA-MAVERICK-FC05 CAUTION: Do not smoke inside the cab or expose the enclosure to direct flames. Product is FLAMMABLE. Be sure to read these instructions thoroughly before opening and installing the enclosure. The installation is best done when the temperature is 70 degrees F.
- Page 2 Soft Doors: 5. Before installing the cab enclosure, you will need to remove the seats and set them aside. 6. Begin installation by hanging the Door Panels from the top by using the 3” adhesive Velcro strips as shown in the photos below: 7.
- Page 3 8. Now move around the door and attach the remaining Velcro strips in the same manner. Down the front of the door place the edge of the door against the side of the windshield and run the Velcro strips under it with the 3”...
- Page 4 12. The next part of the door is to place the 8” adhesive Velcro on the rear facing edge of the entrance to match up with the front bottom section of the door as shown in the photo below. 13. Lastly on the door you will take the strap that is sewn to the center webbing strip towards the front of the door and run it through the safety net buckle and back to the ladder lock buckle.
-
Page 5: Rear Window
Rear Window: 14. Begin installation of the Rear Window by hanging it by the four double-sided Velcro strips sewn along the top of the panel. The main difference here is that the top of the Rear Window will be on the inside of the roll cage as shown in the photo below. - Page 6 18. Take the two straps with the grommet holes and attach them to the bottom clamp of the windshield with the strap pointing upwards towards the top. 19. Now take two of the straps with Velcro and attach them to the lower portion of the rear bar of the roll cage.
- Page 7 Cab to either extreme hot or cold temperatures when storing. 3. A special cleaner conditioner is available from Falcon Ridge that will greatly increase the service life of the Cab Enclosure. In addition, if additional hook and loop sets are needed, they can also be ordered.
-
Page 8: Return Policy
Any returns submitted to Falcon Ridge without a return authorization number will be charged a 20% restocking fee. If ordered from one of Falcon Ridge’s many distributors, you must first call them and see what their return policy is. Once your item reaches our production facility, our customer satisfaction team will inspect your item to ensure unused, factory new condition.