Table of Contents
Advertisement
Quick Links
NOTICE TO END USERS
This User's Guide & Technical Reference is for assisting system
manufacturers and end-users in setting up and installing the mainboard.
Every effort has been made to ensure that the information in this manual is
accurate. Soltek Computer Inc. is not responsible for printing or clerical errors.
Information in this document is subject to change without notice and does not
represent a commitment on the part of Soltek Computer Inc.
No part of this manual may be reproduced, transmitted, translated into any
language in any form or by any means, electronic or mechanical, including
photocopying and recording, for any purpose without the express written
permission of Soltek Computer Inc.
Companies and products mentioned in this manual are for identification
purpose only. Product names appearing in this manual may or may not be
registered trademarks or copyrights of their respective companies.
SOLTEK COMPUTER INC. PROVIDES THIS MANUAL "AS IS " WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO
EVENT SHALL SOLTEK COMPUTER INC. BE LIABLE FOR ANY LOSS OR
PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION
OF BUSINESS, OR FOR INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES OF ANY KIND, EVEN IF SOLTEK
COMPUTER INC. HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL
OR PRODUCT.
© Copyright 1999 Soltek Computer Inc. All Rights Reserved.
Web site : http://www.soltek.com.tw
E-mail
: support@soltek.com.tw
Edition : September 1999
Version : 1.0
: SL-67EB
Model
+
serials
1
Advertisement
Table of Contents
Related Manuals for SOLTEK SL-67EB Plus
Summary of Contents for SOLTEK SL-67EB Plus
- Page 1 Every effort has been made to ensure that the information in this manual is accurate. Soltek Computer Inc. is not responsible for printing or clerical errors. Information in this document is subject to change without notice and does not represent a commitment on the part of Soltek Computer Inc.
-
Page 2: Table Of Contents
C O N T E N T CHAPTER 1 INTRODUCTION...............4 n FEATURES....................4 CPU .......................4 ....................4 HIPSET L2 C ....................4 ACHE ..................4 EMORY BIOS ......................5 I/O F ................5 UPER UNCTION ..................5 THER UNCTIONS ..........6 AINBOARD LAYOUT WITH DEFAULT SETTING CHAPTER 2 HARDWARE SETUP ............7 n CPU TYPE CONFIGURATION............7 ............8 YSTEM... - Page 3 ..............30 OWER ANAGEMENT ETUP P/PCI C ............34 ONFIGURATION ETUP ................. 37 ETUP EFAULTS ..............38 NTEGRATED ERIPHERALS ............... 42 UPERVISOR ASSWORD IDE HDD A ..............43 ETECTION & E ................43 ETUP ................43 ITHOUT AVING...
-
Page 4: Chapter 1 Introduction
Chapter 1 INTRODUCTION n FEATURES 1. Supports Intel Pentium II/III, Celeron CPUs using SLOT 1 at 233 ~ 700MHz or higher CPU. 2. Supports CPU voltage auto detect circuit. 3. Supports 66/100MHz Bus Clock with auto detects. (BIOS supports 103/112MHz BUS Clock without auto detects.) Chipset 1. -
Page 5: Bios
BIOS 1. AWARD Plug and Play BIOS. 2. Supports Advanced Power Management Function and ACPI Function. 3. Flash Memory for easy upgrade. 4. BIOS supports CPU Core Voltage Setting. 5. Supports BIOS Writing Protection. Super I/O Function 1. Integrated USB (Universal Serial Bus) controller with two USB ports. 2. -
Page 6: Mainboard Layout With Default Setting
Mainboard layout with default setting The default settings of the following figure is for the Celeron / Pentium II 233/66MHz or 350/100MHz. Upper Lower ATX Power C l o c k G e n e r a t o r Intel 440BX Chipset... -
Page 7: Chapter 2 Hardware Setup
Chapter 2 HARDWARE SETUP n CPU Type Configuration The CPU Type Configuration CPU Model SW1 Setting CPU Ratio Celeron 233/66 3.5 x Pentium II / III 350/100 Celeron 266/66 4.0 x Pentium II / III 400/100 Celeron 300/66 4.5 x Pentium II / III 450/100 Celeron 333/66 5.0 x... -
Page 8: System Memory Configuration
Celeron 433/66 6.5 x Pentium II / III 650/100 Celeron 466/66 7.0 x Pentium II / III 700/100 Celeron 500/66 7.5 x Pentium II / III 750/100 Celeron 533/66 8.0 x Pentium II / III 800/100 System Memory Configuration This 82440BX mainboard supports 168pin DIMM of 4MB, 8MB, 16MB, 32MB, 64MB, 128MB and 256MB to form a memory size between 8MB to 768MB(SDRAM). -
Page 9: Bus Ratio Select
Bus Ratio Select SW1 DIP1 ~ DIP4 3.0x 3.5x 4.0x 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 4.5x 5.0x 5.5x 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 6.0x 6.5x... -
Page 10: Jumper Settings
n Jumper Settings JP2: Keyboard Power Select Keyboard Power On Disabled(default) Enabled NOTE: 1. If the JP2 is fixed by jumperwire then the board does not support keyboard power on function. 2. When the keyboard power on function shows any compatible problem, choose Disabled and report the keyboard model to the vender/maker. -
Page 11: Jp3/Jp4: Usb Port Select
JP3/JP4: USB Port Select USB Port JP3 / JP4 Redirect USB port 1 to USB connector(Default) Redirect USB 1 to AGP port JP6: Power Lost Resume This jumper allows you to use the switch of ATX power supply to control ON/OFF directly instead of using the power switch on the motherboard. -
Page 12: J2 Switch Signal Summary
J2 Switch Signal Summary Signal Description HDD LED Signal HDD LED Connector HDD LED Signal N.C. No Connection Infrared Transmit Signal Infrared Receive Signal Infrared Connector (low speed) Infrared Receive Signal (high speed) N.C. No Connection Power Switch(for ATX Power) SUSPEND signal SUSPEND IDE LED Activity Light (J2 pin1-4) -
Page 13: J3 Switch Signal Summary
J3 Switch Signal Summary Signal Description Speaker Signal No Connection Speaker Connector Reset Signal Reset Switch N.C. No Connection Power LED Connector No Connection Keylock Signal Keylock Connector N.C. No Connection SUSPEND LED signal SUSPEND LED No Connection Speaker Connector (J3 pin1-4) The speaker connector is a 4-pin connector for connecting the system and the speaker. -
Page 14: Other Connectors
n Other connectors • ‚ : PS/2 MOUSE : USB0 ƒ „ : LPT1 : PS/2 KEYBOARD … † : USB1 : COM1 ‡ : COM2 • ‚ : HDD LED : INFRARED (IR) ƒ „ : POWER SWITCH : SUSPEND CONNECTOR …... -
Page 15: Flash Memory Update Installation
n Flash Memory Update Installation 1. Download BIOS files and flash utility from your board vendor. They are: awdflash.exe and .bin file. 2. Copy them to bootable diskette and boot from diskette. 3. The diskette cannot include memory manager e.g. emm386.exe,qemm and himem.sys, otherwise there will appear an error message “insufficient memory”. -
Page 16: Chapter 3 Bios Setup
Chapter 3 BIOS SETUP This mainboard comes with the AWARD BIOS from AWARD Software Inc. Enter the Award BIOS Program Main Menu by: 1. Turn on or reboot the system. After a series of diagnostic checks, the following message will appear: PRESS <DEL>... - Page 17 3. Using the arrows on your keyboard selects an option, and press <Enter>. Modify the system parameters to reflect the options installed in your system. 4. You may return to the Main Menu anytime by pressing<ESC>. 5. In the Main Menu, “SAVE AND EXIT SETUP” saves your changes and reboots the system, and “EXIT WITHOUT SAVING”...
-
Page 18: Standard Cmos Setup
Standard CMOS Setup Standard CMOS Setup allows you to record some basic system hardware configuration and set the system clock and error handling. You only need to modify the configuration values of this option when you change your system hardware configuration or the configuration stored in the CMOS memory gets lost or damaged. - Page 19 A short description of the screen options is as follows: Date (mm:dd:yy) Set the current date and time. Time (hh:mm:ss) Primary This field records the specifications (Secondary) for all non-SCSI hard disk drives Master/Slave installed in your system. Refer to The respective documentation on how to install the drives.
-
Page 20: Bios Features Setup
BIOS Features Setup BIOS Features Setup allows you to improve your system performance or set up system features according to your preference. Run the BIOS Features Setup as follows: 1. Choose “BIOS FEATURES SETUP” from the Main Menu and a screen with a list of options will appear. - Page 21 A short description of screen options follows: Virus Warning Enabled: Activates automatically when the system boots up causing a warning message to appear if there is anything attempting to access the boot sector or hard disk partition table. Disabled: No warning message will appear when there is something attempting to access the boot sector or hard disk partition table...
- Page 22 Boot Up Floppy Enabled (default): During POST, Seek BIOS checks the track number of the floppy disk drive to see whether it is 40 or 80 tracks. Disabled: During POST, BIOS will not check the track number of the floppy disk drive. Boot Up Choose On (default) or Off.
- Page 23 Security Option Choose System or Setup (default). This option prevents unauthorized system boot-up or use of BIOS Setup. PCI/VGA palette Choose Enabled or Disabled (default). Snoop It determines whether or not the MPEG ISA cards can work with PCI/VGA. Choose Enabled or Disabled ¡ ] d efault ¡ ^ . Assign IRQ for VGA Enabled: Add one IRQ to VGA...
- Page 24 3. Press <ESC> and follow the screen instructions to save or disregard your settings.
-
Page 25: Chipset Features Setup
Chipset Features Setup Chipset Features Setup changes the values of the chipset registers. These registers control the system options. Run the Chipset Features Setup as follows: 1. Choose “CHIPSET FEATURES SETUP” from the Main Menu and a screen with a list of options will appear. ROM PCI/ISA BIOS CHIPSET FEATURES SETUP AWARD SOFTWARE, INC. - Page 26 A short description of screen options follows: AUTO Auto Configuration selects CONFIGURATION predetermined optimal values of chipset parameters. When Disabled, chipset parameters revert to setup information stored in CMOS. Many fields in this screen are not available when Auto Configuration is Enabled. EDO DRAM The DRAM timing is controlled by the Speed Selection DRAM Timing Registers.
- Page 27 SDRAM Defines the length of time for Row Precharge Address Strobe is allowed to Time precharge. The Choice: 2, 3. SDRAM CAS You can select CAS latency time in HCLKs of 2/2 or 3/3. The system Latency Time board designer should set the values in this field, depending on the DRAM installed.
- Page 28 Choose Enabled or Disabled ¡ ] d efault ¡ ^ . Video BIOS Cacheable When Enabled, the access to the VGA BIOS ROM addressed at C0000H- C7FFFH is cached. Choose Enabled or Disabled ¡ ] d efault ¡ ^ . Video RAM Cacheable When Enabled, the access to the VGA...
- Page 29 Choose 4, 8, 16, 32, 64 ¡ ] d efault ¡ ^ , 128 AGP Aperture or 256MB. Memory mapped and graphics data structures can reside in a Graphics APERTURE. This Area is like a linear buffer. BIOS will auto report the starting address of this buffer to the O.S.
-
Page 30: Power Management Setup
Power Management Setup Power Management Setup sets the system’s power saving functions. 1. Choose “POWER MANAGEMENT SETUP” from the Main Menu and a screen with a list of options will appear. ROM PCI/ISA BIOS POWER MANAGEMENT SETUP AWARD SOFTWARE, INC. ACPI Function :Disabled **Reload Global Timer Events**... - Page 31 A short description of screen options follows: ACPI Function This item allows you to enable/disable the Advanced Configuration and Power Interface (ACPI). The choice: Enabled, Disabled. Power Choose Max. Saving, User Define Management (default), Disabled, or Min. Saving. PM Control by Choose Yes (default) or No.
- Page 32 Standby Mode These two options allow you to choose Suspend Mode the mode for the different timers. The Standby Mode turns off the VGA monitor, and the Suspend Mode turns off the CPU and saves the energy of the system. HDD Power Down When enabled and after the set time of system inactivity, the hard disk drive will be powered down while all other...
- Page 33 Resume by Enabled: Wake up the system at Alarm assigned time, and also, the user needs to set both “Date Alarm” and “Time Alarm”2 options. Disabled ¡ ] d efault ¡ ^ : Disabled this feature. Enabled ¡ ] d efault ¡ ^ : Wake up the system Wake On LAN form LAN card ¡...
-
Page 34: Pnp/Pci Configuration Setup
PnP/PCI Configuration Setup PnP/PCI Configuration Setup configures the PCI bus slots. Run the Chipset Features Setup as follows: 1. Choose “PnP/PCI CONFIGURATION SETUP” from the Main Menu and a screen with a list of options will appear. ROM PCI/ISA BIOS PNP/PCI CONFIGURATION AWARD SOFTWARE, INC. - Page 35 A short description of screen options follows: PNP OS Installed Yes: OS supports Plug and Play function. No (default): OS doesn’ t support Plug and Play function. Note: BIOS will automatically disable all PnP resources except the boot device card when you select Yes on Non-PnP OS..
- Page 36 Used MEM Choose 8K, 16K, 32K or 64K. Length* With the above two functions, users can define where the used memory address is located and its corresponding length of the legacy area. BIOS will skip the UMB area which is used by the legacy device to avoid memory space conflict.
-
Page 37: Load Setup Defaults
Load Setup Defaults “Load Setup Defaults” option loads the default system values to the system configuration fields. If the CMOS is corrupted the defaults are loaded automatically. Choose this option and the following message will appear: “Load Setup Defaults (Y/N)? N” To use the Setup defaults, change the prompt to “Y”... -
Page 38: Integrated Peripherals
Integrated Peripherals Integrated Peripherals option changes the values of the chipset registers. These registers control system options in the computer. 1. Choose “INTEGRATED PERIPHERALS” from the Main Menu and a screen with a list of options will appear. ROM PCI/ISA BIOS INTEGRATED PERIPHERALS AWARD SOFTWARE, INC. - Page 39 A short description of screen options is as follows: IDE HDD Block Choose Enabled (default) or Disabled. Mode If your hard disk size is large than 540MB, choose Enabled, and, if you are using the IDE HDD Auto Detection option, the BIOS will choose this option automatically.
- Page 40 USB Keyboard Enabled: Enables the function Support when the USB keyboard is being used. Disabled ¡ ] d efault ¡ ^ : When the AT keyboard be used. KBC Input Clock Choose 6MHz, 8MHz ¡ ] d efault ¡ ^ , 12MHz or 16MHz.
- Page 41 Onboard Parallel Choose the printer I/O address: Port 378H/IRQ7 (default), 3BCH/IRQ7, 278H/IRQ5, Disabled Parallel Port Choose Normal (default), ECP/EPP Mode EPP, or ECP mode. The mode depends on the external device connected to this port. ECP Mode Use Choose DMA3 (default) or DMA1. Most sound cards use DMA1.
-
Page 42: Supervisor/User Password
Supervisor/User Password These two options allow you to set your system passwords. Normally, the supervisor has a higher ability to change the CMOS setup option than the user. The way to set up the passwords for both Supervisor and User are as follows: 1. -
Page 43: Ide Hdd Auto Detection
IDE HDD Auto Detection IDE HDD Auto Detection detects the parameters of an IDE hard disk drive and automatically enters them to the Standard CMOS Setup screen. The screen will ask you to select a specific hard disk for Primary Master after you select this option.
Need help?
Do you have a question about the SL-67EB Plus and is the answer not in the manual?
Questions and answers