Watts AMES 2000SS Series Instruction, Installation, Maintenance And Repair Manual

Watts AMES 2000SS Series Instruction, Installation, Maintenance And Repair Manual

Double check valve assemblies, double check detector assemblies

Advertisement

Quick Links

Installation, Maintenance, and Repair Manual
Series 2000SS, 3000SS
Double Check Valve Assemblies
Double Check Detector Assemblies
Sizes: 2½" – 12"
WARNING
!
Read this Manual BEFORE using this equipment.
Failure to read and follow all safety and use information can
result in death, serious personal injury, property damage, or
damage to the equipment.
Keep this Manual for future reference.
WARNING
!
You are required to consult the local building and plumbing
codes prior to installation. If the information in this manual
is not consistent with local building or plumbing codes,
the local codes should be followed. Inquire with governing
authorities for additional local requirements.
WARNING
!
Need for Periodic Inspection/Maintenance: This product must
be tested periodically in compliance with local codes, but at least
once per year or more as service conditions warrant. If installed on
a fire suppression system, all mechanical checks, such as alarms
and backflow preventers, should be flow tested and inspected in
accordance with NFPA 13 and/or NFPA 25. All products must be
retested once maintenance has been performed. Corrosive water
conditions, and/or unauthorized adjustments or repair could render
the product ineffective for the service intended. Regular checking
and cleaning of the product's internal components helps assure
maximum life and proper product function.
Product information is subject to change without notice and
supersedes all previous publications.
2000SS-OSY-TS FxG
Integrated supervisory tamper switches on
gate valves add protection against fire
NOTICE
For Australia and New Zealand, line strainers should be installed
between the upstream shutoff valve and the inlet of the backflow
preventer.
NOTICE
The flange gasket bolts for the gate valves should be retightened
during installation as the bolts may have loosened due to storage
and shipping.
Testing
For field testing procedure, refer to Ames installation sheets
IS-A-ATG-1 found at watts.com.
For other repair kits and service parts, refer to the Backflow
Prevention Products Repair Kits & Service Parts price list
PL-A-RP-BPD found at watts.com.
For technical assistance, contact your local Ames representative.
RP/IS-A-2000SS/3000SS

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AMES 2000SS Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Watts AMES 2000SS Series

  • Page 1 Testing For field testing procedure, refer to Ames installation sheets IS-A-ATG-1 found at watts.com. For other repair kits and service parts, refer to the Backflow Prevention Products Repair Kits & Service Parts price list PL-A-RP-BPD found at watts.com.
  • Page 2 Installation of Fire Alarm Systems Assure All Devices Are Properly wiring of the tamper switch to the fire alarm control panel. (For Grounded. more information refer to Tamper Switch Wiring Instructions at watts.com.) Wiring Notes CAUTION • Connection to power limited circuitry is required.
  • Page 3 O-ring groove and apply an FDA-approved lubricant to the O-ring. Figure 3 Figure 4 For repair kits and parts, refer to the Backflow Prevention Products Repair Kits & Service Parts price list No. 2 Cam-Check DC Cam arm torsion spring PL-A-RP-BPD found at watts.com.
  • Page 4 USA: Backflow T: (978) 689-6066 • F: (978) 975-8350 • AmesFireWater.com USA: Control Valves T: (713) 943-0688 • F: (713) 944-9445 • AmesFireWater.com Canada: T: (888) 208-8927 • F: (905) 481-2316 • AmesFireWater.ca Latin America: T: (52) 55-4122-0138 • AmesFireWater.com RP/IS-A-2000SS/3000SS 2218 EDP#7016812 © 2022 Watts...

This manual is also suitable for:

Ames 3000ss series

Table of Contents