Advertisement
Advertisement
Related Manuals for NIIMBOT D101
Summary of Contents for NIIMBOT D101
- Page 1 D101 Operation Manual...
-
Page 2: Table Of Contents
Basic Parameters Basic Usage Display of Indicator Light Guide to APP Usage Cleaning Steps Precautions Warranties... -
Page 3: Basic Parameters
Basic Parameters Model D101 Color White Material Printing method Thermal printing Printing resolution 203dpi 30mm/s~60mm/s Printing speed Label width 10~25mm Effective printing 24mm width Applicable paper Adding machine paper and types transparent paper... - Page 4 One warranty card, Accompanying one type-C data cable supplies Connection mode Bluetooth Supports barcodes Barcode printing and QR codes Printing content Text/patterns/designs Battery type and 1200mAh lithium battery capacity 3~4 hours Charging duration Charging interface Type-c Voltage of incoming 5V-1A current 4 hours of continuous Battery life...
-
Page 5: Basic Usage
Basic Usage Slide to the left to open the lid �. Slide to the left to open the lid 90° �.Opening angle... - Page 6 02 0 5 Paper case baffle �. Requirements for installation of paper case baffle (the baffle has been installed before delivery, and can be used directly for ��mm backing paper labels, but should be removed for ��mm backing paper labels).
- Page 7 03 0 6 Right Left �. Installation of consumables: Insert the roll of paper on the right, with the printing surface facing the switch.
- Page 8 �.Close the lid, and slide to the right end About the new machine: NIIMBOT label printer is generally charged before the delivery for the startup. If you cannot start up your new printer, one possible reason is low battery level. The printer can be started up after being charged for 20 minutes.
-
Page 9: Display Of Indicator Light
Indicator Light Descriptions Indicator Light status Description light color Blue Slow flash Bluetooth not connected Blue Quick flash Printing or charging Bluetooth connected, Blue Not flashing battery fully charged Bluetooth not connected Slow flash and low battery level Printing, or charging and Quick flash low battery level Bluetooth connected,... -
Page 10: Guide To App Usage
Guide to App Usage It only takes two steps to start a new marking experience Download the "NiiMbot" application from the App Store or Google Play. APP Open the lid and place the consumables Available on the App Store GET IT ON... - Page 11 Bluetooth connection mode On your phone or device, turn Bluetooth on. Then start up the printer, and open the app. Switch Switch on the Bluetooth Screen Mirroring Long press the switch button to activate the label printer Press the [Unconnected] button on the right corner of the app, and then click [Search Device].
- Page 12 Press the blue [Connect] button to the right of the correct printer model, and Bluetooth will connect.
- Page 13 Press the [Help] button on the right corner of the app to choose from the demo videos that can be played in the list of [Software - Hardware]. 9:41 AM 100% 9:41 NiiMbot Help D101 Help Center 教程 Printer D110 Series Template scanning Software...
-
Page 14: Faq
Q: Why can’ t the label printer be fully charged when it is connected to a laptop for charging, and why does it switch off automatically after being disconnected? A: The laptop's USB port does not have a sufficient and stable enough voltage to ensure stable charging conditions. - Page 15 Q: Does the label printer support auto-shutdown? A: The label printer will shut down automatically after Bluetooth has been disconnected or the app logged out for 15 minutes, to save power and protect battery life. Q: Why does the label printer keep printing blank labels when working normally? A: It is possible that the label paper has been placed in the wrong direction.
- Page 16 Q: Why is the color printed on the label paper very light? A： 1、 The label paper is not NIIMBOT paper and may be chipless. 2、 The actual printed quantity exceeds the quantity required by the chip, and the self-check page can be viewed.
- Page 17 A： 1、 The D101 label printer currently is only applicable to the special label papers in the D101 series. Using the label papers of other brands will lead to failure.
- Page 18 Q: Does the label printer support batch printing, and how many paper sheets can be printed at a time? A: D101 supports continuous printing and batch printing. The app can currently print up to 999 labels at a time, but...
- Page 19 Q: App error, the prompt says "lack of paper" A: It is most likely one of the following possibilities: 1. No paper is placed in the machine 2. The paper case baffle is not installed or the paper case baffle is not installed in its proper place for 15mm backing paper labels.
- Page 20 Q: How can I make it so that the content is placed in the middle when editing the label? A: On the right side of the edit page’ s [Style] section, where there is a button to the left or the right with the content in the middle, press this button to adjust the position of the label content in the edit box.
-
Page 21: Cleaning Steps
Cleaning Steps In order to clean the platen, follow these steps: 1.Shut down the printer; 2.Open the paper case cover and find the print head (as shown in the figure). In case of printing having just finished, wait for the print head to cool completely; 3. - Page 22 Print head Notes: （1） Ensure the printer is powered off during daily maintenance; （2） Do not touch the surface of the print head with your hands or with metal objects, and do not scratch the surface of the print head, roller or sensor with tweezers;...
-
Page 23: Precautions
Precautions 1.Please keep the product and its accessories in a safe place that is out of the reach of children to keep them out of harm’ s way. 2.Please do not open the paper case cover when the printer is printing. 3.Please ensure that the paper case is clean before using the printer. - Page 24 6.Please do not disassemble the printer without authorization. When the printer is disassembled, return and exchange will not be accepted. 7.Do not use the power adapter when the power cord is damaged, otherwise, it may result in electric shocks, fire and power adapter damage. 8.
- Page 25 14. If you encounter any problem with your use of the machine, please contact the dealer or our customer service staff. NIIMBOT provides the very highest level of after-sales service for customers all over the world!
-
Page 26: Warranties
Warranties 1.From the date of purchase, the warranty period of the print head of the product is 3 months or the time when the printing distance reaches 30km (whichever comes first), and that of other parts is 12 months. 2.Carry-in service is adopted as the warranty method and users need to bring the product to the sales service center. - Page 27 Any damage caused by unauthorized disassembly and repair or modification. Print omissions caused by scratches on print head. Inconsistency of purchase record with the serial number of the machine under warranty. Any damage due to human factors or other force majeure.
- Page 28 Wuhan Jingchen Intelligent ldentificationTechnology Co., Ltd. Address: Creative Workshop No. 5, Creative World, Yezhihu West Road, Hongshan District, Wuhan Email: service@niimbot.com Website: www.niimbot.net...