Page 2
YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Page 3
Thermal Network Speed dome·Quick Start Guide REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS;...
Page 4
Thermal Network Speed dome·Quick Start Guide 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg).
Page 5
Thermal Network Speed dome·Quick Start Guide Cautions Do not drop the device or subject it to physical shock. Wipe the device gently with a clean cloth and a small quantity of ethanol, if necessary. Do not aim the lens at the sun or any other bright light. ...
Thermal Network Speed dome·Quick Start Guide 1 Preparation Basic Requirement All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations in your local region. Check the package contents and make sure that the device in the package is ...
Thermal Network Speed dome·Quick Start Guide 2 Appearance Description There are two kinds of thermal network speed domes: Type I speed dome, and Type II speed dome. The appearance description of two cameras are shown below. 2.1 Speed dome Appearance Refer to the following figures for Type I thermal speed dome overview and dimensions.
Thermal Network Speed dome·Quick Start Guide Table 2-1 Descriptions of Cable Interface Description Network Cable Video Cable Alarm Out Audio Cable Alarm In RS-485 Power Cable SD Card Slot 2.2 Cable Descriptions The cable interfaces of speed dome are shown in Figure 2-2. The cables of RS-485, power supply, alarm inputs, alarm outputs, etc.
Thermal Network Speed dome·Quick Start Guide 2.3 Alarm In/Out Connections This section is only for the speed dome with alarm in/out functions. The speed dome can be connected with alarm inputs (0~5VDC) and alarm outputs. Refer to the following diagrams for alarm output: JQC- 3FG GND OUT Relay...
Thermal Network Speed dome·Quick Start Guide 3 Installing the Speed dome Before you start: 1. Check the package contents and make sure that the device in the package is in good condition and all the assembly parts are included. 2. Please turn off the power of the speed dome before connecting the cables. ...
Thermal Network Speed dome·Quick Start Guide 3.1 Monitoring Distance Range Electric lens is adopted for the thermal channel of speed dome. It supports auto-focus function and remote focus function. For different lens focal length, the monitoring range is shown in the table below: Table 3-1 Monitoring Range (Pixel Interval: 17um) Lens Focal Length/mm MRAD...
Thermal Network Speed dome·Quick Start Guide This table is for reference only, and the actual detection range may vary according to different camera settings, mounting condition, monitor and so When the weather is fine and the atmospheric visibility is normal, the ...
Thermal Network Speed dome·Quick Start Guide Figure 3-1 Remove Protective Sticker 2. Remove the cover on the back of the speed dome. Insert the SD card to the SD card slot and install the cover back. SD Card Slot Figure 3-2 SD Card Slot 3.4 Installing Speed Dome 1.
Page 15
Thermal Network Speed dome·Quick Start Guide 2). Drill four Φ12 expansion screw holed on the wall and insert the delivered screws into the holes. Figure 3-4 Drill Screw Holes 3). Secure the wall mounting bracket with 4 hex nuts and washers. Figure 3-5 Secure the Bracket 2.
Page 16
Thermal Network Speed dome·Quick Start Guide 2). Hook the two ends of the safety rope to the back box of the speed dome and the bracket respectively. 3). Hitch the speed dome onto the head cover with the hook on the back box. Figure 3-8 Hang the Speed Dome 4).
Thermal Network Speed dome·Quick Start Guide Lock Screw Figure 3-10 Secure the Speed dome The bracket in Figure 2-10 is the recommended bracket for this series of speed dome, and a pendent adapter is required if any other bracket is selected.
Thermal Network Speed dome·Quick Start Guide 4 Setting the System over the LAN You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center.
Thermal Network Speed dome·Quick Start Guide 4.2.1 Activation via Web Browser Steps: 1. Power on the system, and connect the system to the network. 2. Input the IP address into the address bar of the web browser, and click Enter to enter the activation interface.
Thermal Network Speed dome·Quick Start Guide Figure 4-3 SADP Interface 3. Create a password and input the password in the password field, and confirm the password. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Page 21
Thermal Network Speed dome·Quick Start Guide Please refer to section 3.2 to activate the system if it is inactive. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP. Figure 4-4 Modify the IP Address 4.
Thermal Network Speed dome·Quick Start Guide 5 Operating via Web browser 5.1 Accessing the System System Requirement: Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 / Server 2003 / Server 2008 32bits CPU: Intel Pentium IV 3.0 GHz or higher RAM: 1G or higher Display: 1024×...
Thermal Network Speed dome·Quick Start Guide Figure 5-1 Login Interface 5. Install the plug-in before viewing the live video and managing the network speed dome. Please follow the installation prompts to install the plug-in. You may have to close the web browser to finish the installation of the plug-in.
Page 24
Thermal Network Speed dome·Quick Start Guide Menu Bar PTZ Control Show or hide PTZ control Live View Window panel Live View Parameters Toolbar Preset/Patrol/Pattern Figure 5-3 Live View Page Menu Bar: Click each tab to enter Live View, Playback, Picture, and Configuration page respectively.
Thermal Network Speed dome·Quick Start Guide 6.2 Frequently Asked Questions (FAQ) 6.2.1 Device Running Error Question: The device fails to start up or reboots repeatedly. The device constantly powers off unexpectedly when you pan/tilt the device or call preset. ...
Page 27
Thermal Network Speed dome·Quick Start Guide Examine if the IE plug-in is well installed. Change the Website Blocker settings if necessary. For cross-domain routing, enable the UPnP of device, or set manual mapping to port No. 80, 8000, or 554. ...