Craftmade Braxton BRX52 Installation Manual

Craftmade Braxton BRX52 Installation Manual

Hide thumbs Also See for Braxton BRX52:

Advertisement

Quick Links

Braxton
Installation Guide
For Model:
BRX52
E192641
net weight of fan: 22.27 lb. (10.1 kg)
READ THESE INSTRUCTIONS AND

Table of Contents:

Warranty. pg. 10
SAVE THEM FOR FUTURE USE
PRINTED IN CHINA

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Braxton BRX52 and is the answer not in the manual?

Questions and answers

Summary of Contents for Craftmade Braxton BRX52

  • Page 1: Table Of Contents

    READ THESE INSTRUCTIONS AND SAVE THEM FOR FUTURE USE Braxton Installation Guide For Model: BRX52 Table of Contents: Safety Tips. pg. 1 Unpacking Your Fan. pg. 2 Parts Inventory. pg. 2 Installation Preparation. pg. 3 Hanging Bracket Installation. pg. 3 Fan Assembly.
  • Page 2: Safety Tips

    SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS.
  • Page 3: Unpacking Your Fan

    1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. *The four motor stabilization pieces may be dicarded at this time. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs.
  • Page 4: Installation Preparation

    3. Installation Preparation. blade edge To prevent personal injury and damage, ensure that the hanging location allows the blades a inches clearance of 7ft. (2.13m) from the floor and 30in. 7 feet (76cm) (76cm) from any wall or obstruction. (2.13m) This fan is suitable for room sizes up to 400 square feet (37.2 square meters).
  • Page 5: Fan Assembly. Pgs

    5. Fan Assembly. set screw stop pin Remove hanging ball from downrod provided by loosening set screw on hanging ball. Lower hanging ball and remove stop pin and then slide hanging ball hanging ball off of the downrod. [Refer to diagram 1.] Loosen yoke set screws and nuts at top of motor housing.
  • Page 6: Wiring. Pgs

    wood 5. Fan Assembly. (cont.) ceiling joist safety cable With the hanging bracket secured to the outlet box and able loop to support the fan, you are now ready to hang your fan. Grab the fan firmly with two hands. Slide downrod through opening in hanging bracket and let hanging ball rest on the hanging bracket.
  • Page 7: Canopy Assembly

    6. Wiring. (cont.) [PLEASE NOTE: Wall and/or handheld remote Modifications not approved by the party responsible for compliance could void the user's authority to operate the equipment. control must be used for fan to operate. If you do *NOTE: This equipment has been tested and found to comply with the limits for a Class B not wish to use the wall control, please proceed to digital device, pursuant to Part 15 of the FCC Rules.
  • Page 8: Blade Assembly

    8. Blade Assembly. motor housing WARNING: To reduce the risk of serious bodily injury, DO NOT use power tools to assemble the blades. If screws are overtightened, blades may crack and break. blade Time Saver: Washers for blade screws can be set on each blade screw prior to installing blades.
  • Page 9: Assembly Of Handheld Remote Control

    10. Assembly of Handheld Remote Control. IN ORDER TO USE THE HANDHELD REMOTE CONTROL, remote PLEASE CONTINUE WITH SECTION 10 for remote control control assembly instructions. If you have already installed the cover wall control but do not wish to use the handheld remote control, please proceed to Section 11.
  • Page 10: Automated Learning Process./Activating Code

    11. Automated Learning Process./Activating Code. CAUTION: The wall and/or handheld remote control can be programmed to multiple receivers or fans. If this is not desired, turn wall switch off to any other programmable receiver or fan. Restore electrical power and then, if using wall control, set slider switch on wall control to the ON position.
  • Page 11: Troubleshooting

    Service at 1-800-486-4892 to arrange for return of fan. 2. Check to be sure wall control (optional use) is wired Return fan, shipping prepaid, to Craftmade. We will repair properly. or ship you a replacement fan, and we will pay the return 3.

Table of Contents