Download  Print this page

HP LD4201 User Manual

Digital signage displays.
Hide thumbs

Advertisement

HP LD4201, LD4210 and LD4710
Digital Signage Displays
User Guide

Advertisement

   Also See for HP LD4201

   Related Manuals for HP LD4201

   Summary of Contents for HP LD4201

  • Page 1 HP LD4201, LD4210 and LD4710 Digital Signage Displays User Guide...
  • Page 2 Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. This document contains proprietary information that is protected by copyright.
  • Page 3: About This Guide

    About this guide This guide provides information on setting up the display, installing drivers, using the On-Screen Display menu, troubleshooting, and technical specifications. WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life.
  • Page 4 About this guide ENWW...
  • Page 5: Table Of Contents

    Connecting RGB ... 22 Connecting DisplayPort (480p/576p/720p/1080i/1080p) ... 23 Connecting HDMI (480p/576p/720p/1080i/1080p) ... 23 Connecting LAN (HP LD4210 and HP LD4710 only) ... 25 Connecting daisy chain displays ... 26 4 Operating the display ... 28 Software and utilities ... 28 The information file ...
  • Page 6 Appendix B Technical specifications ... 49 HP Digital Signage Display ... 49 HP LD4201 and HP LD4210 dimensions (with optional stand and speakers) ... 51 HP LD4710 dimensions (with optional stand and speakers) ... 53 Recognizing preset display resolutions ... 54 Preset display modes ...
  • Page 7 Transmission/Receiving Protocol ... 59 01. Power (Command: a) ... 59 02. Input Select (Command: b) (Main Picture Input) ... 61 03. Aspect Ratio (Command: c) (Main picture format) ... 62 04. Screen Mute (Command: d) ... 62 05. Volume Mute (Command: e) ... 63 06.
  • Page 8 Materials disposal ... 96 Disposal of waste equipment by users in private households in the European Union ... 96 Chemical substances ... 96 HP recycling program ... 96 Restriction of Hazardous Substances (RoHS) ... 96 Turkey EEE regulation ... 97 viii Output waveform ...
  • Page 9: Product Features

    Support VESA compliant mounting interface with 600 x 400 mm (23.62 x 15.75 in) hole pattern ● for the HP LD4201 and HP LD4210 models and 800 x 400 mm (31.50 x 15.75 in) hole pattern for the HP LD4710 model...
  • Page 10: Optional Accessories

    Power cord ● DisplayPort cable ● HDMI cable ● RGB (VGA) cable ● Optional accessories Optional accessories (purchased separately) might vary depending on the model. Stand kit ● Speakers kit ● Wall mount kit ● Chapter 1 Product features ENWW...
  • Page 11: Safety And Maintenance Guidelines

    CAUTION: Do not place the device in a location where water may drip and/or splash on the device. Do not place an object that contains water, such as a flower vase, on the device. ENWW www.hp.com/ergo Important safety information...
  • Page 12: Maintenance Guidelines

    If the display is not operating properly or has been dropped or damaged, contact an authorized HP dealer, reseller, or service provider. Use only a power source and connection appropriate for this display, as indicated on the label/ ●...
  • Page 13: Cleaning The Display

    Cleaning the display Turn off the display and unplug the power cord from the back of the unit. Dust the display by wiping the screen and the cabinet with a soft, clean antistatic cloth. For more difficult cleaning situations, use a 50/50 mix of water and Isopropyl alcohol. CAUTION: Spray the cleaner onto a cloth and use the damp cloth to gently wipe the screen surface.
  • Page 14: Setting Up The Display

    Installing the stand (sold separately) Take the parts for the stand out of the box. HP LD4201 and LD4210—Four screws M4 x 32 mm (1.26 in) and stand ● Figure 3-1 HP LD4710—Four screws M4 x 10 mm (0.39 in) and stand...
  • Page 15 Place a soft cloth on the table and place the display with the screen facing downward. Connect the stand as shown in the following figure. Figure 3-3 HP LD4201 and LD4210—Sliding the stand onto the display Figure 3-4 HP LD4710—Sliding the stand onto the display...
  • Page 16 Use the screws to secure the stand on the rear side of the product as shown in the figure. Figure 3-5 HP LD4201 and LD4210—Securing the stand to the display Figure 3-6 HP LD4710—Securing the stand to the display Chapter 3 Setting up the display...
  • Page 17: Connecting The Speakers (sold Separately)

    Connecting the speakers (sold separately) Mount the speakers onto the display. Figure 3-7 Mounting the speakers Use the four Taptite D3 x 12 mm (0.47 in) screws to secure the speakers to the display. Figure 3-8 Securing the speakers to the display ENWW Connecting the speakers (sold separately)
  • Page 18 After installing the speakers, use the cable holders and cable ties (available on select models) to secure the speaker cables. Figure 3-9 Using the cable holders (feature available on select models) Figure 3-10 Using the cable ties (feature available on select models) Chapter 3 Setting up the display ENWW...
  • Page 19: Rotating To The Portrait Position

    After installing the speakers, connect to the SPEAKER input terminal by connecting the proper color match for the left and right speakers. Figure 3-11 Connecting to the input terminal Rotating to the portrait position When installing the display in the portrait position, rotate it clockwise based on its front. The display can be rotated in only one direction.
  • Page 20: Using The Remote Control

    Using the remote control Inserting the batteries Slide off the battery cover. Insert the batteries with correct polarity (+/-). Close the battery cover. NOTE: To prevent environmental pollution, dispose of used batteries in accordance with your local recycling guidelines. Figure 3-13 Inserting batteries Chapter 3 Setting up the display ENWW...
  • Page 21: Identifying Remote Control Buttons

    Identifying remote control buttons Figure 3-14 Remote control buttons ENERGY MONITOR SAVING MARK MUTE AUTO MENU BACK TILE Component Power on/off MONITOR ON or Number Volume up (+) or down (-) MUTE MENU Up/down/left/right arrows ENWW INPUT BRIGHT NESS EXIT Function...
  • Page 22 Navigates one step back in an interactive application Enables the display lock Use with the HP Media Sign Player option lists in the USB menu Adjusts the Energy Saving mode Opens the Input Source menu options (RGB, HDMI/DVI, and DisplayPort)
  • Page 23: Identifying Display Components

    Power and OSD control buttons Power cord receptacle to connect the display to an electrical outlet RGB IN/OUT, HDMI/DVI, RS-232-C IN/OUT, Audio IN, DisplayPort IN/OUT, USB, LAN (HP LD4210 and HP LD4710 only) Connections for external speakers Identifying display components...
  • Page 24: Display Control Panel

    Display control panel Figure 3-17 HP LD4201 and HP LD4210—Display control panel 1 2 3 4 5 6 7 8 Figure 3-18 HP LD4710—Display control panel 1 2 3 4 5 6 7 8 Component Power ON/OFF AUTO/SET OSD select/adjust button...
  • Page 25: Display Ports

    DP OUT supports cloning of connections with DisplayPort cables from display to display. USB connects a USB storage device to the HP Media Sign Player. LAN connects the display directly to a media player/computer or to a network directly or indirectly by a router, hub, or switch using the LAN cable.
  • Page 26 Security cable provision—To help prevent theft, a security cable provision is available on the rear of the display. The cable and lock required to connect to the display are available separately and can be purchased from HP. Figure 3-20 VESA mounting holes...
  • Page 27: Connecting To External Devices

    ● Connecting HDMI (480p/576p/720p/1080i/1080p) on page 23 ● Connecting LAN (HP LD4210 and HP LD4710 only) on page 25 ● Connect the audio cable (sold separately) to the Audio (RGB/DVI) (1) connector on the rear of the display and the other end to the Line Out port (2) on the media player/computer if the video signal connection is from either a RGB (VGA) or DVI connector on the media player/computer.
  • Page 28 Before connecting the power cord, please read the power-cord safety precautions in the Figure 3-22 Figure 3-23 Chapter 3 Setting up the display Important safety information on page HP LD4201 and HP LD4210—Connecting the power cord HP LD4710—Connecting the power cord ENWW...
  • Page 29 Turn on power to the display by pressing the power button (1). Figure 3-24 HP LD4201 and HP LD4210—Power button Figure 3-25 HP LD4710—Power button Turn on the media player/computer. Select an input signal: Press the INPUT button on the remote control to open the Input List, select the appropriate input signal, and then press the OK button to save your change.
  • Page 30: Connecting Rgb

    Connecting RGB For analog operation, connect the D-Sub signal cable to the RGB IN (1) connector on the rear of the display and the other end to the connector (2) on the media player/computer. NOTE: If connecting to a Mac media player/computer, use the standard Mac adapter (3)–not included.
  • Page 31: Connecting Displayport (480p/576p/720p/1080i/1080p)

    Connecting DisplayPort (480p/576p/720p/1080i/1080p) Connect the DisplayPort cable to the DP IN port on the display and to the DisplayPort OUT port on the media player/computer, and then connect the display power cord. Figure 3-28 Connecting DisplayPort input to a media player/computer Select an input signal.
  • Page 32 Connect an HDMI to DVI signal cable to the HDMI/DVI port on the display, and then to the ● DVI port on the media player/computer. For AUDIO input from the media player/computer (this is only needed with DVI input signal connections), connect the RCA-PC audio cable (cable not included) to the display and to the Audio OUT ports on the media player/computer, then connect the display power cord.
  • Page 33: Connecting Lan (hp Ld4210 And Hp Ld4710 Only)

    Intranet. A LAN connection with the display establishes communication between your media player/ computer and the display. This enables the use of the HP Network Sign Manager program, running on the connected media player/computer, to assign an IP address to the display, to change display settings, and to set up HP Media Sign Player options, play lists, and On/Off schedule times.
  • Page 34: Connecting Daisy Chain Displays

    Connecting daisy chain displays Multiple displays (up to 25) can be connected in a daisy chain (connect several displays together in Tile Mode) to a computer using DisplayPort IN/OUT or with the combination of RGB IN/OUT and RS-232-C IN/OUT ports on the display. To connect displays in a daisy chain, the displays must all be connected with the same input/output source (DisplayPort IN/OUT, RS-232-C IN/OUT, or RGB IN/OUT) as shown in the figures below.
  • Page 35 Figure 3-34 Daisy chain connection—RS-232-C RS-232C RS-232C RS-232C RS-232C (CONTROL) (CONTROL) (CONTROL) (CONTROL) Connecting daisy chain displays ENWW...
  • Page 36: Operating The Display

    HP Media Sign Player. For more details on the HP Media Sign Player, refer to Using the HP Media Sign Player on page Manager software, refer to the HP Network Sign Manager User Guide (available only in English) included on the CD provided with the display.
  • Page 37: Installing The .inf And .icm Files

    Installing the .INF and .ICM files You can install the .INF and .ICM files from the CD or download them from the HP displays support website. Installing from the CD To install the .INF and .ICM files on the media player/computer from the CD: Insert the CD in the media player/computer CD-ROM drive.
  • Page 38: Using The Auto-adjustment Function (rgb Input Source Only)

    Using the auto-adjustment function (RGB INPUT source only) You can optimize the screen performance by using the on the remote control) and the Auto-adjustment Pattern Utility software on the CD provided. NOTE: Do not use this procedure if the display is set to use a DisplayPort or HDMI/DVI input source. If the display is using a PC analog signal input, this procedure can correct the following image quality conditions: Fuzzy or unclear focus...
  • Page 39: Using The Remote Control To Adjust The Osd

    Icon Main menu Tile Using the remote control to adjust the OSD Use the OSD to adjust the screen image based on your viewing preferences. To access the OSD, do the following: If the display is not already on, press the power button to turn on the display. Press the MENU button (1) on the remote control.
  • Page 40: Osd Menu Selections

    OSD menu selections The following table lists the On-Screen Display (OSD) menu selections and their functional descriptions. Icon Main menu PICTURE Chapter 4 Operating the display Submenu Description Aspect Ratio Selects from the following screen image sizes: 16:9—Widescreen mode. ● 1:1—Picture format is 1:1 aspect ratio.
  • Page 41 Icon Main menu ENWW Submenu Description Color—Adjusts the color to desired level. ◦ Tint—Adjusts the tint to a desired level. ◦ NOTE: If the Picture Mode setting is set to Vivid, Standard, Cinema, Sport, or Game, the above adjustments will be automatically set to predefined settings. Advanced Select from the following screen color adjustment settings: Control...
  • Page 42 Icon Main menu AUDIO Chapter 4 Operating the display Submenu Description Expert 1 and Select from the following settings: Expert 2 Control Dynamic Contrast—Optimizes the contrast ● automatically according to the brightness of the reflection. Noise Reduction—Removes the noise up to the point ●...
  • Page 43 Off. Interface Select Select the connection you are using for remote display management. For more information, refer to the HP Network Sign Manager User Guide (available in English only) included on the CD provided with the display.
  • Page 44 See your network administrator for the correct manual entries to enter. For more details on setting the display IP Address, refer to the HP Network Sign Manager User Guide (available in English only) included on the CD provided with the display.
  • Page 45: Selecting An Aspect Ratio

    USB storage device with the HP Media Sign Player. Set Password Allows you to set a password for the HP Media Sign Player. NOTE: password is entered. If you should forget your password, enter 7777 in the password field and that will take you to the Set Password menu to change the password.
  • Page 46: Clock

    Clock The Clock menu allows you to reset the clock manually if the current time is incorrect. Press the MENU button, and then use the down arrow ▼ or up arrow ▲ button to select the TIME menu. Press the right arrow ► button, and then use the down arrow ▼ or up arrow ▲ button to select the Clock menu.
  • Page 47: Auto Off

    Key Lock is set ON, display options might only be set or changed with the remote control or using the HP Network Sign Manager with HP LD4210 and HP LD4710. Press the MENU button, and then use the down arrow ▼ or up arrow ▲ button to select the OPTION menu.
  • Page 48: Using Ism Method

    Using ISM Method Displaying a static image on the screen for a prolonged period of time could result in burn-in or image sticking. To avoid burn-in or image sticking or to fix a ghost or burned-in image, do not display a fixed image for prolonged periods of time.
  • Page 49 Each display must be connected to every other display, using either RGB IN/RGB OUT or DP IN/ DP OUT as shown in the following figure. If you want to issue display commands from the media player/computer, you must connect each display with RS-232-C IN/RS-232-C OUT just like the video connections.
  • Page 50: Using The Hp Media Sign Player

    ● Photo selection and menu options View—Starts the HP Media Sign Player. You will see the first image selected in the Photo List ● and the Option box. This image remains on the display until you select Slideshow in the Option box.
  • Page 51: Using Music List

    Options on full-sized photo view Slideshow—Starts the HP Media Sign Player. Only the files marked or selected are played ● unless there are no files marked, and then all files in the selected folder play in the order they appear in the Photo List. Set the time interval for all of the slides in the slide show in the Options dialog box.
  • Page 52: Using Movie List

    The Play ►, Pause II, Stop ■, Reverse ◄◄, and Forward ►► buttons on the remote control are also available to use when playing music. Play—Starts the HP Media Sign Player. After Play is highlighted and OK is pressed, the selected ●...
  • Page 53 Maximum FPS (frame per second) can be reached only at SD level. FPS is 25 FPS (720*576) or ● 30 FPS (720*480) depending on Resolution. Files more than 25 FPS or 30 FPS or higher might not be played properly. ●...
  • Page 54: Appendix A Troubleshooting

    Make sure that the signal cable is properly connected. Press the INPUT button on the remote control to check the input signal. Install the display driver, which is provided with the display or download from the HP website www.hp.com. See if the Plug and Play function is supported by referring to the video card user manual.
  • Page 55 Problem Possible cause Key Lock On Key Lock message function is appears when turned on. pressing the Menu button. The screen looks Screen is out of abnormal; adjustment. screen position is wrong. Lines appear on Screen is out of the background adjustment.
  • Page 56: Using The Web

    Preparing to call technical support If you cannot solve a problem using the troubleshooting tips in this section, you might need to call technical support. Contact your regional HP authorized service provider. Have the following information available when you call: Display model number ●...
  • Page 57: Appendix B Technical Specifications

    Technical specifications NOTE: All performance specifications are provided by the component manufacturers. Performance specifications represent the highest specification of all HP's component manufacturers' typical level specifications for performance; actual performance might vary either higher or lower. HP Digital Signage Display...
  • Page 58 Input connector Environmental Operating conditions temperature Storage temperature Appendix B Technical specifications HP LD4201 HP LD4210 220 W Typical 220 W Typical ≤ 1 W (RGB) / 2 W (HDMI/ ≤ 1 W (RGB) / 2 W (HDMI/ DVI) DVI) ≤...
  • Page 59: Hp Ld4201 And Hp Ld4210 Dimensions (with Optional Stand And Speakers)

    Figure B-1 HP LD4201 and HP LD4210—Front and side view ENWW HP LD4201 and HP LD4210 dimensions (with optional stand and speakers) HP LD4201 HP LD4210 10 W + 10 W (R + L) 10 W + 10 W (R + L) 0.7 Vrms...
  • Page 60 Figure B-2 HP LD4201 and HP LD4210—Back view Appendix B Technical specifications ENWW...
  • Page 61: Hp Ld4710 Dimensions (with Optional Stand And Speakers)

    HP LD4710 dimensions (with optional stand and speakers) Figure B-3 HP LD4710—Front and side view Figure B-4 HP LD4710—Back view ENWW HP LD4710 dimensions (with optional stand and speakers)
  • Page 62: Recognizing Preset Display Resolutions

    Recognizing preset display resolutions The display resolutions listed below are the most commonly used modes and are set as factory defaults. This display automatically recognizes these preset modes and they will appear properly sized and centered on the screen. Preset display modes Table B-2 Factory preset display modes Preset...
  • Page 63: Power Indicator

    HDMI/DVI 1080i 1080p NOTE: DTV/PC selection on HDMI/DVI inputs is available for media player/computer resolutions— 640 x 480/60 Hz, 1280 x 720/60 Hz, 1920 x 1080/60 Hz and DTV resolutions—480p, 720p, 1080p. Power indicator Mode On Mode Sleep Mode Off Mode ENWW DisplayPort (DTV)
  • Page 64: Appendix C Command Reference

    Use this method to connect several products to a single PC. You can control several products at a time by connecting them to a single PC. If the Set ID menu in Option is set to OFF, the monitor ID value should be set between 1 and 99.
  • Page 65: Communication Parameter

    Communication parameter Baud Rate—9600 baud rate (UART) ● Data Length—8 bit ● Parity Bit—None ● Stop Bit—1 bit ● Flow Control—None ● Communication Code—ASCII code ● Use a crossed (reverse) cable ● Command reference list 01. Power 02. Input Select 03.
  • Page 66 22. Tile V Position 23. Tile H Size 24. Tile V Size 25. Tile ID Set 26. Natural Mode (In Tile Mode) 27. Picture Mode (PSM) 28. Sound Mode 29. Fan Fault Check 30. Elapsed Time Return 31. Temperature Value 32.
  • Page 67: Transmission/receiving Protocol

    Transmission/Receiving Protocol Transmission [Command1][Command2][][Set ID][][Data][Cr] *[Command 1] First command (k, j, m, d, f, x) *[Command 2] Second command (a to z) *[Set ID] Set up the Set ID number of product. range: 01H to 63H. by setting '0', server can control all products. When operating with more than 2 sets using set ID as '0' at the same time, do not check the ack message.
  • Page 68 [Data] 0: Power Off 1: Power On Acknowledgement [a][][Set ID][][OK][Data][x] To show the status of Power On/Off. Transmission [k][a][][Set ID][][FF][Cr] Acknowledgement [a][][Set ID][][OK][Data][x] [Data] 0: Power Off 1: Power On Appendix C Command reference ENWW...
  • Page 69: Input Select (command: B) (main Picture Input)

    02. Input Select (Command: b) (Main Picture Input) To select input source for the Set. You can also select an input source using the INPUT button on the remote control. Transmission [k][b][][Set ID][][Data][Cr] [Data] 7: RGB (PC) 8: HDMI/DVI (HD-DVD) 9: HDMI (PC) A: DisplayPort (HD-DVD) B: DisplayPort (PC)
  • Page 70: Aspect Ratio (command: C) (main Picture Format)

    03. Aspect Ratio (Command: c) (Main picture format) To adjust the screen format. You can also adjust the screen format using the ARC (Aspect Ratio Control) button on remote control or in the Screen menu. Transmission [k][c][][Set ID][][Data][Cr] [Data] 1: Normal Screen (4:3) 2: Wide Screen (16:9) 4: Zoom [HDMI (HD-DVD), DisplayPort (HD- DVD)]...
  • Page 71: Volume Mute (command: E)

    [d][][Set ID][][OK][Data][x] 05. Volume Mute (Command: e) To control On/Off of the Volume Mute. Transmission [k][e][][Set ID][][Data][Cr] [Data] 0: Volume Mute On (Volume Off) 1: Volume Mute Off (Volume On) Acknowledgement [e][][Set ID][][OK][Data][x] [Data] 0: Volume Mute On (Volume Off) 1: Volume Mute Off (Volume On) 06.
  • Page 72: Contrast (command: G)

    Real data mapping 07. Contrast (Command: g) To adjust screen contrast. You can also adjust the contrast in the Picture menu. Transmission [k][g][][Set ID][][Data][Cr] [Data] Min: 00H to Max: 64H Acknowledgement [g][][Set ID][][OK][Data][x] Real data mapping Appendix C Command reference 0: Step 0 A: Step 10 F: Step 15...
  • Page 73: Brightness (command: H)

    08. Brightness (Command: h) To adjust screen brightness. You can also adjust the brightness in the Picture menu. Transmission [k][h][][Set ID][][Data][Cr] [Data] Min: 00H to Max: 64H Refer to “Real data mapping” as shown below. Acknowledgement [h][][Set ID][][OK][Data][x] Real data mapping 09.
  • Page 74: Tint (command: J) (video Timing Only)

    Real data mapping Acknowledgement [i][][Set ID][][OK][Data][x] [Data] Min: 00H to Max: 64H (Hexadecimal code) 10. Tint (Command: j) (Video Timing only) To adjust the screen tint. You can also adjust the tint in the Picture menu. Transmission [k][j][][Set ID][][Data][Cr] [Data] Red: 00H to Green: 64H (Hexadecimal code) Appendix C Command reference...
  • Page 75: Sharpness (command: K) (video Timing Only)

    Real data mapping Acknowledgement [j][][Set ID][][OK][Data][x] [Data] Red: 00H to Green: 64H Tint real data mapping 11. Sharpness (Command: k) (Video Timing only) To adjust the screen Sharpness. You can also adjust the sharpness in the Picture menu. Transmission [k][k][][Set ID][][Data][Cr] [Data] Min: 00H to Max: 64H (Hexadecimal code)
  • Page 76: Osd Select (command: L)

    Real data mapping Acknowledgement [k][][Set ID][][OK][Data][x] [Data] Min: 00H to Max: 64H 12. OSD Select (Command: l) To control OSD on/off to the set. Transmission [k][l][][Set ID][][Data][Cr] [Data] 0: OSD Off 1: OSD On Acknowledgement [l][][Set ID][][OK][Data][x] [Data] 0: OSD Off 1: OSD On 13.
  • Page 77: Balance (command: T)

    This function, when controlling RS-232C, locks the remote control and the local keys. Transmission [k][m][][Set ID][][Data][Cr] [Data] 0: Off 1: On Acknowledgement [m][][Set ID][][OK][Data][x] [Data] 0: Off 1: On 14. Balance (Command: t) To adjust the sound balance. Transmission [k][t][][Set ID][][Data][Cr] [Data] Min: 00H to Max: 64H (Hexadecimal code)
  • Page 78: Color Temperature (command: U)

    Balance: L50 to R50 15. Color Temperature (Command: u) To adjust the screen color temperature. Transmission [k][u][][Set ID][][Data][Cr] [Data] 0: Medium 1: Cool 2: Warm Acknowledgement [u][][Set ID][][OK][Data][x] [Data] 0: Medium 1: Cool 2: Warm 16. Abnormal state (Command: z) Abnormal State: Used to Read the power off status when Stand-by mode.
  • Page 79: Ism Method (command: J P)

    [Data] 0: Normal (Power on and signal exist) 1: No signal (Power on) 2: Turn the display off by remote control 3: Turn the display off by sleep time function 4: Turn the display off by RS-232-C function 8: Turn the display off by off time function 9: Turn the display off by auto off function 17.
  • Page 80: Key (command: M C)

    [u][][Set ID][][OK][Data][x] 19. Key (Command: m c) To send IR remote key code. Transmission [m][c][][Set ID][][Data][Cr] Data Key code: Refer to the Acknowledgement [c][][Set ID][][OK][Data][x] 20. Tile Mode (Command: d d) Change a Tile Mode. Transmission [d][d][][Set ID][][Data][x] [Data] Description 00 or 11 Tile mode is off.
  • Page 81: Tile V Position (command: D F)

    Transmission [d][e][][Set ID][][Data][x] [Data] Min: 00H to Max: 14H 00H: Step -10 (Left) 14H: Step 10 (Right) Acknowledgement [e][][Set ID][][OK/NG][Data][x] 22. Tile V Position (Command: d f) To set the Vertical position. Transmission [d][f][][Set ID][][Data][x] [Data] Min: 00H to Max: 14H 00H: Step -10 (Left) 14H: Step 10 (Right) Acknowledgement...
  • Page 82: Tile V Size (command: D H)

    Real data mapping Acknowledgement [g][][Set ID][][OK/NG][Data][x] 24. Tile V Size (Command: d h) To set the Vertical size. Transmission [d][h][][Set ID][][Data][x] [Data] Min: 00H to Max: 64H Real data mapping Acknowledgement [h][][Set ID][][OK/NG][Data][x] Appendix C Command reference 0: Step 0 A: Step 10 F: Step 15 10: Step 16...
  • Page 83: Tile Id Set (command: D I)

    25. Tile ID Set (Command: d i) To assign the Tile ID for Tiling function. Transmission [d][i][][Set ID][][Data][x] [Data] Min: 00H to Max: 19H (Hexadecimal code) Acknowledgement [i][][Set ID][][OK/NG][Data][x] 26. Natural Mode (In Tile Mode) (Command: d j) To assign the Title Natural mode for Tiling function. Transmission [d][j][][Set ID][][Data][x] [Data]...
  • Page 84: Picture Mode (command: D X)

    27. Picture Mode (Command: d x) To adjust the picture mode. Transmission [d][x][][Set ID][][Data][x] Data Structure Data MODE (Hex) Vivid Standard Cinema Sport Game Expert 1 Expert 2 Acknowledgement [x][][Set ID][][OK/NG][Data][x] 28. Sound Mode (Command: d y ) To adjust the Sound mode. Transmission [d][y][][Set ID][][Data][X] Data Structure...
  • Page 85: Fan Fault Check (command: D W )

    Data MODE (Hex) Sport Game Acknowledgement [y][][Set ID][][OK/NG][Data][x] 29. Fan Fault check (Command: d w ) To check the Fan fault of the display. Transmission [d][w][][Set ID][][Data][x] [Data] Data is always FF (in Hex) Data ff: Read Status Acknowledgement [w][][Set ID][][OK/NG][Data][x] [Data] [Data] is the status value of the Fan fault.
  • Page 86: Temperature Value (command: D N)

    [Data] Data is always FF (in Hex) Acknowledgement [l][][Set ID][][OK/NG][Data][x] [Data] The data means used hours. (Hexadecimal code) 31. Temperature value (Command: d n) To read the inside temperature value. Transmission [d][n][][Set ID][][Data][x] [Data] Data is always FF (in Hex) Acknowledgement [n][][Set ID][][OK/NG][Data][x] [Data]...
  • Page 87: Auto Volume (command: D U)

    [p][][Set ID][][OK/NG][Data][x] [Data] 0: Lamp Fault 1: Lamp OK 2: N/A(DPM/Power Off) 33. Auto volume (Command: d u) Automatically adjust the volume level. Transmission [d][u][][Set ID][][Data][x] [Data] 0: Off 1: On Acknowledgement [u][][Set ID][][OK/NG][Data][x] 34. Speaker (Command: d v) Turn the speaker on or off. Transmission [d][v][][Set ID][][Data][x] [Data]...
  • Page 88: Time (command: F A)

    35. Time (Command: f a) Set the current time. Transmission [f][a][][Set ID][][Data1][][Data2][][Data3][Cr] [Data1] 0: Monday 1: Tuesday 2: Wednesday 3: Thursday 4: Friday 5: Saturday 6: Sunday [Data2] 00H to 17H (Hours) [Data3] 00H to 3BH (Minutes) Acknowledgement [a][][Set ID][][OK/NG][Data1][Data2][Data3][x] When reading data, FFH is inputted for [Data1], [Data2] and [Data3].
  • Page 89 [Data1] f1h to f4h (read one index) f1: read 1st index of On Time List f2: read 2nd index of On Time List f3: read 3rd index of On Time List f4: read 4th index of On Time List [Data2] 00h to 17h, ffh (Hours) [Data3] 00h to 3bh, ffh (Minutes)
  • Page 90: Off Timer (on/off Timer) Time (command: F E)

    37. Off Timer (On/Off Timer) Time (Command: f e) Set Off Timer. Transmission [f][e][][Set ID][][Data1][][Data2][][Data3][Cr] [Data1] f1h to f4h (read one index) f1: read 1st index of On Time List f2: read 2nd index of On Time List f3: read 3rd index of On Time List f4: read 4th index of On Time List...
  • Page 91: Scheduling Input Select (command: F U) (main Picture Input)

    Acknowledgement [e][][Set ID][][OK][Data1][Data2][Data3][x] 38. Scheduling Input select (Command: f u) (Main Picture Input) To select input source for TV depending on day. Transmission [f][u][][Set ID][][Data1][][Data2][Cr] [Data1] f1h to f4h(write/read one index) f1: read 1st index of On Time Input f2: read 2nd index of On Time Input f3: read 3rd index of On Time Input f4: read 4th index of On Time Input Data...
  • Page 92: Sleep Time (command: F F)

    39. Sleep Time (Command: f f) Set Sleep Time. Transmission [f][f][][Set ID][][Data][Cr] [Data] 0: Off 1: 10 2: 20 3: 30 4: 60 5: 90 6: 120 7: 180 8: 240 Acknowledgement [f][][Set ID][][OK/NG][Data][x] 40. Auto Off (Command: f g) Set Auto Sleep.
  • Page 93: Power On Delay (command: F H)

    41. Power On Delay (Command: f h) Set the schedule delay when the power is turned on (Unit: second). Transmission [f][h][][Set ID][][Data][Cr] [Data] 00H to 64H (Data value) Real data mapping Acknowledgement [h][][Set ID][][OK/NG][Data][x] 42. Language (Command: f i) Set the OSD language. Transmission [f][i][][Set ID][][Data][Cr] ENWW...
  • Page 94: Dpm Select (command: F J)

    [Data] 0: English 1: French 2: German 3: Spanish 4: Italian 5: Portuguese 6: Chinese 7: Japanese 8: Korean 9: Russian Acknowledgement [i][][Set ID][][OK/NG][Data][x] 43. DPM Select (Command: f j) Set the DPM (Display Power Management) function. Transmission [f][j][][Set ID][][Data][Cr] [Data] 0: Off 1: On...
  • Page 95: Energy Saving (command: F I)

    [Data] 0: Picture Reset 1: Screen Reset 2: Factory Reset Acknowledgement [k][][Set ID][][OK/NG][Data][x] 45. Energy saving (Command: f I) To set the Power saving mode. Transmission [f][I][][Set ID][][Data][Cr] [Data] 0: Off 1: (static level 1) 2: (static level 2) 3: (static level 3) Acknowledgement [I][][Set ID][][OK/NG][Data][x] 46.
  • Page 96: Serial No. Check (command: F Y)

    [o][][Set ID][][OK/NG][Data][x] 47. Serial no. Check (Command: f y) To read the serial numbers Transmission [f][y][][Set ID][][Data][Cr] [Data] Data FF (to read the serial numbers) Acknowledgement [y][][Set ID][][OK/NG][Data1]to[Data13][x] [Data] The data format is ASCII Code. 48. S/W Version (Command: f z) Check the software version.
  • Page 97: Ir Codes

    [Data] 60H: RGB (PC) 90H: HDMI/DVI (HD-DVD) A0H: HDMI/DVI (PC) B0H: DisplayPort (HD-DVD) C0H: DisplayPort (PC) Acknowledgement [b][][Set ID][][OK][Data][x] [Data] 60H: RGB (PC) 90H: HDMI/DVI (HD-DVD) A0H: HDMI/DVI (PC) B0H: DisplayPort (HD-DVD) C0H: DisplayPort (PC) IR codes Use this method to connect your wired remote control port on the display. Remote Control IR Code Output waveform Single pulse, modulated with 37.917kHz signal at 455kHz...
  • Page 98: Lead Code

    Repeat frame ● Lead code Repeat code Bit description Bit “0” ● 0.56 ms 1.12 ms Bit “1” ● 0.56 ms 2.24 ms Frame interval: Tf The waveform is transmitted as long as a key is depressed. IR Codes Table Code Function (Hex )
  • Page 99 Code Function (Hex ) Left arrow ◄ POWER ON/OFF MONITOR ON MONITOR OFF MUTE Energy Saving INPUT MENU EXIT Number Key 0 Number Key 1 Number Key 2 Number Key 3 Number Key 4 Number Key 5 Number Key 6...
  • Page 100 Code Function (Hex ) TILE Play ► Stop ■ Pause II Reverse ◄◄ Fast forward ►► RGB PC HDMI/DVI ARC (4:3) ARC (16:9) ARC (ZOOM) Appendix C Command reference Note R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button Discrete IR Code (Input RGB PC Selection) Discrete IR Code (Input HDMI/DVI Selection)
  • Page 101: Appendix D Agency Regulatory Notices

    Agency regulatory notices Federal Communications Commission notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
  • Page 102: Canadian Notice

    Compliance with these directives implies conformity to applicable harmonized European standards (European Norms) that are listed in the EU Declaration of Conformity issued by HP for this product or product family and available (in English only) either within the product documentation or at the...
  • Page 103: German Ergonomics Notice

    0.75 mm² or 18 AWG, and the length of the cord must be between 6 feet (1.8 m) and 12 feet (3.6 m). If you have questions about the type of power cord to use, contact an authorized HP service provider.
  • Page 104: Japanese Power Cord Requirements

    Do not use the power cord received with this product on any other products. Product environmental notices Materials disposal This HP product contains mercury in the fluorescent lamp in the display LCD that might require special handling at end-of-life. Disposal of this material can be regulated because of environmental considerations. For disposal or recycling information, contact the local authorities or the Electronic Industries Alliance (EIA) www.eiae.org.
  • Page 105: Turkey Eee Regulation

    11363-2006 11363-2006 Turkey EEE regulation In Conformity with the EEE Regulation EEE Yönetmeliğine Uygundur ENWW Product environmental notices...

This manual also for:

Ld4210Ld710Ld4710

Comments to this Manuals

Symbols: 0
Latest comments: