Related Manuals for Whispbar K915W
Summary of Contents for Whispbar K915W
- Page 1 K915W Fitting Kit Fitting Instructions for Basic Carrier Revision No: 3C...
- Page 2 Fitting Kit K915W MAX kgs (lbs) Ford Fusion, 5dr Hatch 14-+ 75 kgs (165 lbs) 75 kgs (165 lbs) Mondeo, 5dr Hatch 14-+ 75 kgs (165 lbs) 75 kgs (165 lbs) Mondeo, 5dr Hatch 14-+ 75 kgs (165 lbs) 75 kgs (165 lbs)
- Page 3 Fitting Kit K915W Fusion, 5dr Hatch 14-+ (ZA) -335mm 410mm 957mm 923mm -13 -3/16ths" 16 1/8ths" 37 11/16ths" 36 5/16ths" Mondeo, 5dr Hatch 14-+ (AU) -335mm 410mm 957mm 923mm -13 -3/16ths" 16 1/8ths" 37 11/16ths" 36 5/16ths" Mondeo, 5dr Hatch 14-+ (EU)
-
Page 4: First Time Installation
Fitting Kit K915W First Time Installation Remove parts from inside the package and check. Contact your dealer if any parts are missing or damaged. This kit fits type A, B, C and D. These instructions show type A crossbar fitted. They also apply to type B, C and D. - Page 5 Fitting Kit K915W Use keys to remove covers. Use hex screwdriver to reverse adjusting screw 10 turns. Press adjusting screw and pull crossbar legs out. Refer to the crossbar instructions for crossbar adjustment method. Ensure each end of the crossbar is...
- Page 6 Fitting Kit K915W Remove locking screw. Apply protective strip as shown. Trim if required. A = Grey Refer to the underside of the pad for the part number.
- Page 7 Fitting Kit K915W It is important to put the pads in the correct position on the vehicle. Letters refer to the pad part numbers and position. Pad Part Number: A = 11-04-296 B = 11-04-295 Place rubber pads (supplied with fitting kit) on the vehicle roof.
- Page 8 Fitting Kit K915W Make sure the pad fits into the holes underneath the foot. It is important to put the clamps in the correct position on the vehicle. Letters refer to the part numbers stamped on clamps. Clamp Part Number:...
- Page 9 Fitting Kit K915W Refit locking screw so that it goes through the hole in the clamp. Do not begin to tighten the locking screw. Adjust the legs on the crossbar so that they are positioned equally from the ends of the crossbar, and the clamps engage firmly on the body work of the vehicle.
- Page 10 Fitting Kit K915W Tighten locking screw on both legs evenly. Check crossbar is securely attached to the vehicle. Use keys to fit and lock covers...
- Page 11 Fitting Kit K915W CAUTION: Recheck all fasteners immediately after a load is applied to the crossbars. Regularly check screws are tight.
-
Page 12: Maintenance
Fitting Kit K915W Maintenance Clean the car roof and surfaces of the product that will be in contact with the car roof. Follow the fitting instructions for fitting the product to your vehicle. Make sure all steps are carried out in order. - Page 13 Fitting Kit K915W Check and replace worn out or defective parts. Keep the product clean and maintained. Never drive into a car wash with the roof rack system fitted. Lubricate locks and adjusting screws at regular intervals. Remove the products from the vehicle when not in use.
-
Page 14: Warranty And Disclaimer
Make a claim as soon as practicable by contacting the Whispbar dealer from whom you purchased the product, who will give you instructions on how to proceed. If you are unable to contact the Whispbar dealer, or the dealer is not able to remedy the defect, you should contact Yakima as soon as practicable at: Call: 0800 4776 722 (NZ) or 1800 143 548 (AU) Email: warranty@yakima.co.nz or warranty@yakima.com.au... - Page 15 Yakima or the Whispbar dealer will be borne by you. Following receipt of the product and purchase invoice or receipt, Yakima or the Whispbar dealer must inspect the product to determine whether the claim falls within the warranty. If: 4.1 the claim falls within the warranty, Yakima will remedy any defects in materials or workmanship becoming apparent during the...