Related Manuals for Whispbar K952W
Summary of Contents for Whispbar K952W
- Page 1 K952W Fitting Kit Fitting Instructions for Basic Carrier Revision No: 2B...
- Page 2 Fitting Kit K952W...
- Page 3 Fitting Kit K952W MAX kgs (lbs) Honda Odyssey, 5dr MPV 13-+ 50 kgs (110 lbs) 50 kgs (110 lbs) Odyssey, 5dr MPV 14-+ 50 kgs (110 lbs) 50 kgs (110 lbs)
- Page 4 Fitting Kit K952W Odyssey, 5dr MPV 13-+ (AU) 220mm 1115mm 970mm 903mm 8 11/16ths" 43 7/8ths" 38 3/16ths" 35 9/16ths" Odyssey, 5dr MPV 14-+ (NZ) 220mm 1115mm 970mm 903mm 8 11/16ths" 43 7/8ths" 38 3/16ths" 35 9/16ths"...
-
Page 5: First Time Installation
Fitting Kit K952W First Time Installation Remove parts from inside the package and check. Contact your dealer if any parts are missing or damaged. This kit fits type A, B, C and D. These instructions show type A crossbar fitted. They also apply to type B, C and D. - Page 6 Fitting Kit K952W Use hex screwdriver to reverse adjusting screw 10 turns. Press adjusting screw and pull crossbar legs out. Refer to the crossbar instructions for crossbar adjustment method. Ensure each end of the crossbar is adjusted equally. Attaches to factory-fitted mounting points...
- Page 7 Fitting Kit K952W Tighten adjusting screw to 2 Nm (1.5 ft lb) hand tight. Remove plastic clamp block by gripping bar leg with fingers and push firmly with thumbs until clamp block drops out behind leg. Select plastic internal block (from fitting kit) and insert into foot.
- Page 8 Fitting Kit K952W Fitment Lift and pull ditch molding back towards you. Note: ditch molding remains on vehicle. Remove factory clips. Mark a reference point for the front and rear mounting points with a pen as shown. Use drill bit supplied, to drill holes in marked positions.
- Page 9 Fitting Kit K952W Re-install rubber ditch mould back into roof channel and click into place. Attach hex nut adaptor to stud as shown. Tighten with the spanner provided. Select grubscrews and screw into the vehicle's fixed points. Do not over tighten.
- Page 10 Fitting Kit K952W It is important to put the pads in the correct position on the vehicle. Letters refer to the pad part numbers and position. Pad Part Number: A = 219 B = 222 C = 223 Place crossbars on pads ensuring the pads...
- Page 11 Fitting Kit K952W Ensure the plastic knob is in the position shown when fully tightened. Repeat for all legs. Check crossbar is securely attached to the vehicle. Use keys to fit and lock covers Remove the products from the vehicle when not in use.
- Page 12 Fitting Kit K952W CAUTION: Recheck all fasteners immediately after a load is applied to the crossbars. Regularly check screws are tight.
-
Page 13: Maintenance
Fitting Kit K952W Maintenance Never drive into a car wash with the roof rack system fitted. Lubricate locks and adjusting screws at regular intervals. Remove the products from the vehicle when not in use. Make sure all loose parts are stored safely. - Page 14 Fitting Kit K952W Set crossbars a minimum distance of 700mm (27 1/2") apart where no other distance is specified in the fitting instructions. This is especially important when carrying long loads. Check unit is securely attached whenever you refit it to the vehicle. If the unit feels loose, refer to the fitting instructions and readjust.
-
Page 15: Warranty And Disclaimer
Make a claim as soon as practicable by contacting the Whispbar dealer from whom you purchased the product, who will give you instructions on how to proceed. If you are unable to contact the Whispbar dealer, or the dealer is not able to remedy the defect, you should contact Yakima as soon as practicable at: Call: 0800 4776 722 (NZ) or 1800 143 548 (AU) Email: warranty@yakima.co.nz or warranty@yakima.com.au... - Page 16 Yakima or the Whispbar dealer will be borne by you. Following receipt of the product and purchase invoice or receipt, Yakima or the Whispbar dealer must inspect the product to determine whether the claim falls within the warranty. If: 4.1 the claim falls within the warranty, Yakima will remedy any defects in materials or workmanship becoming apparent during the...