Table of Contents
Advertisement
TWO-WAY 6-BUTTON LCD REMOTE STARTER
FOR AUTOMATIC OR MANUAL TRANSMISSION
34-0794 | CT-4311TW
User Guide
It is the responsibility of the vehicle operator to ensure their vehicle is parked
in a safe and responsible manner.
1. a) Manual transmission: When leaving the vehicle, it is the user's responsibility
to ensure that the gearshift lever is in the NEUTRAL position and the parking
brake is engaged in order to avoid accidents upon remote starting.
b) Automatic transmission: When leaving the vehicle, it is the user's
responsibility to ensure that the gearshift lever is in "Park" in order to avoid
accidents upon remote starting.
(Note: Make sure that the automatic vehicle cannot start in "Drive".)
2. It is the user's responsibility to ensure that the remote starter is disabled or put
into valet mode before servicing.
INDUSTRY CANADA USER NOTICE:
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired operation of
the device.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen
that the equivalent isotropically radiated power (EIRP) is not more than that required for successful
communication.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could void the user's authority to operate the
equipment
D1124
2015-08-07
WARNING
- VM -
Canada
Advertisement
Chapters
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ProStart CT-4311TW
Summary of Contents for ProStart CT-4311TW
- Page 1 TWO-WAY 6-BUTTON LCD REMOTE STARTER FOR AUTOMATIC OR MANUAL TRANSMISSION 34-0794 | CT-4311TW User Guide WARNING It is the responsibility of the vehicle operator to ensure their vehicle is parked in a safe and responsible manner. 1. a) Manual transmission: When leaving the vehicle, it is the user’s responsibility to ensure that the gearshift lever is in the NEUTRAL position and the parking brake is engaged in order to avoid accidents upon remote starting.
-
Page 2: Table Of Contents
Table of Contents Government Regulations.........................3 Introduction with SmartStart™ .....................3 Vehicle Presets ..........................4 Heater ............................4 Windshield Wipers, Radio & Headlights ..................4 Using the Transmitter ........................4 LCD Transmitter Basic Confirmations ...................5 Basic Vehicle Operations.......................5 Backlight............................5 Remote Advanced Functions and MENU ..................6 How to Access Default Advanced Remote Functions and MENU..........6 Remote-Starting your Vehicle ......................9 Setting your Vehicle into Ready Mode...................9 Remote Starting ...........................10... -
Page 3: Government Regulations
Government Regulations This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. -
Page 4: Vehicle Presets
Vehicle Presets Heater When leaving the vehicle it is recommended to preset the accessory controls in preparation for the next remote start. Settings for the blower motor (fan), front and rear, should not be left on HIGH. It is recommended to leave the settings on LOW or MEDIUM instead. Windshield Wipers, Radio &... -
Page 5: Lcd Transmitter Basic Confirmations
The functions of the 1-way transmitter are as follows (optional): LOCK: Locks the doors and arms the STARTER KILL (if installed). UNLOCK: Unlocks the doors and disarms the STARTER KILL (if installed). Activates the AUX 1 output if Priority Door Access is configured. TRUNK: Opens the TRUNK or activates the AUX 3 output. -
Page 6: Remote Advanced Functions And Menu
To browse the MENU while the backlight is ON: Press the for at least 1 second and release. The backlight should turn ON. Within 3 seconds, press the button for 2 seconds to access the various functions. Remote Advanced Functions and MENU How to Access Default Advanced Remote Functions and MENU User Transmitter (default) - Page 7 Remote advanced functions and MENU Display Description Parking meter countdown This version of the countdown feature is particularly useful for keeping track of parking meter time: the user may quickly set up the countdown using the Parking Menu. The transmitter will beep once, 5min before the Parking countdown reaches 0 and beeps 6 times once the countdown expires.
- Page 8 Secure: This feature is used to lock the keypad of the transmitter to avoid accidental button press. When the keypad is locked and a button is pressed, the LCD will display “PRESF” for 1 second and goes back to the clock. The transmitter keypad can also be locked as follows: SECUR Press...
-
Page 9: Remote-Starting Your Vehicle
Button Function: The order of LEVELS and MENU can be re-arranged using the Button Function Menu. Details on (page-6). F Button Function FBPRO FBPRO Function Button Programming Menu (15) 1 2 3 M Level 1, level 2, level 3, MENU 2 3 1 M Level 2, level 3, level 1, MENU Function Button... -
Page 10: Remote Starting
THERE ARE THREE POSSIBLE OPTIONS TO COMPLETE READY MODE (programmable by installer) OPTION 2: Manual shut down OPTION 3: Automatic shut OPTION 1: No lock (default) down The engine stops. The engine keeps going until you The engine runs for 8 sec. press either;... -
Page 11: Arming And Disarming The Starter Kill (If Installed)
Arming and Disarming the Starter Kill (if installed) This added security feature will prevent the vehicle from starting with the Ignition key when the starter kill is armed. If the system was installed with the starter kill option, the vehicle will not be able to start with the key unless the system has been unlocked first or put into Valet Mode (page 13). -
Page 12: Remote Starter Features
Remote Starter Features Remote Door Locks If your Remote Car Starter was installed with the Remote Door Locks option, you will have the convenience of remote keyless entry. To LOCK your doors and ARM the system: Press and hold the button for approx. -
Page 13: Valet Modes
Valet Modes When the vehicle is in Valet Mode, the remote starter and alarm functionalities are disabled. If the vehicle needs to be serviced, or if you park it indoors, Valet Mode will prevent the engine from being remote-started accidentally. Any of the following features will put the remote car starter into Valet Mode: Ignition Valet: This feature allows you to set Valet Mode using the ignition key. -
Page 14: Quick Lockout Tm
Quick Lockout (Also called Secure Panic.) For fast protection in emergency situations, the system will LOCK all doors when you press the brake pedal while you hear the Horn sounding. (Quick Lockout is only available when Panic mode has been triggered.) Cold Weather Mode If the vehicle has a manual transmission, Ready mode (page-9) should be set before entering Cold Weather mode. -
Page 15: Disable/Enable Led Flashing
Disable/Enable LED Flashing To disable the LED: Press simultaneously until the remote beeps once, pauses for 2 seconds, then beeps once again. Release the buttons. The parking lights will flash 3 times. To Enable the LED: Press simultaneously until the remote beeps once, pauses for 2 seconds, then beeps once more. -
Page 16: Engine Run Time
1-way remote: 1. Rapidly press AUX twice. While the remote’s LED is flashing, press to remote start the vehicle. Note: The AUX 2 output can be activated by pressing the button. Engine Run Time On a gas engine, the Remote Car Starter can be programmed to run the engine for 3, 15, or 25 minutes (15 minutes by default). -
Page 17: Aux 1
To take the system out of Home Valet™ mode: Turn the ignition key to the IGNITION ON (RUN) position. The system will warn you if someone attempts to start your vehicle while it stands in Home Valet™ mode. The parking lights will turn ON then OFF, then flash twice, pause, then flash twice again. AUX 1 Note: This 500 mA negative Aux 1 output can be used for many different applications Priority Door:... -
Page 18: Oem-Style Alarm
OEM-Style Alarm The OEM-style alarm (if configured by your installer) monitors the doors, hood and ignition switch of your vehicle. It will sound the horn if a door or the hood is opened, or if the key is turned in the ignition. -
Page 19: Multi-Level Features
Multi-Level Features The multi-level features allow you to access different features of your vehicle or of a second car by pressing the button once, twice or three times. For convenience purpose, the order of LEVELS and MENU can be re-arranged through FBPRO setting (page-6) Features: MENU: see page-6 for complete lists of MENU available. -
Page 20: Troubleshooting Transmitting Range
Troubleshooting Transmitting Range Many factors may affect the operating range of the transmitter. Some of these are: The condition of the battery in the transmitter. The operating environment (for example: downtown radio-frequency noise, airports, cellular phone towers…) Metal: any type of metal will affect operating range. This includes the metal in the car. The shape of the vehicle can affect range as well;...
Need help?
Do you have a question about the CT-4311TW and is the answer not in the manual?
Questions and answers