Deluxe Pendant - Greenlee 855 Instruction Manual

Operation — Optional Deluxe Pendant (cont'd)
9. Pressing ENTER:
a. is required to store any numerical value into
memory.
b. when on SELECT CONDUIT SIZE screen will
proceed to the next screen without changing the
size.
c. when on SELECT CONDUIT TYPE screen will
proceed to the next screen without changing the
type.
d. when on SELECT TYPE OF BEND screen will
proceed to the next screen without changing the
bend type.
e. when on SELECT ANGLE screen will proceed
to the next screen without changing the angle.
f. when on SELECT HEIGHT screen will proceed
to the next screen without changing the height.
If the bend type is a stub, then pressing ENTER
will proceed to the MARK 1= ... Press ENTER
TO GO ON screen.
g. when on SELECT LENGTH screen will proceed
to the next screen without changing the
LENGTH.
h. when on MARK 1= ... Press ENTER TO GO
ON screen will proceed to next screen.
i. when on any of the three SET FRONT OF
HOOK AT... screens will do nothing.
j. when in Accuracy Adjust mode will save any
change to the last displayed adjust angle and
exit Accuracy Adjust mode.
10. Pressing any of the 11 numeric keys and
ENTER when the display is prompting SELECT
ANGLE will display and store the numbers as they
are pressed. Angles will only be displayed in whole
numbers. Pressing any of the numeric keys and
ENTER when the SELECT HEIGHT and SELECT
LENGTH prompts are displayed will display and
store the numbers immediately after a HEIGHT ="
or LENGTH =" display as soon as the numbers are
pressed. At any other point, pressing the numeric
keys will do nothing. All numeric displays will be
limited to two decimal places, except as noted
above.
Greenlee Textron / Subsidiary of Textron Inc.
855 Smart Bender™
11. Pressing BEND:
a. if the conduit size and type have not been
selected, will display the SELECT CONDUIT
SIZE screen but will not start the bender.
b. with the conduit size, type and no bend angle or
an angle of 0 in memory will run the bender.
The pendant will display the actual bend angle,
or SET HOME POSITION until the home switch
has been tripped. Operation will stop and the
prior screen will return when the BEND key is
released.
c. with conduit size, type and a bend angle other
than 0 in memory will run the bender. The
pendant will display the actual bend angle, or
SET HOME POSITION until the home switch
has been tripped. Operation will stop when the
bend key is released, when the actual bend
angle equals or exceeds the angle set in
memory, or when the maximum shoe rotation
has been reached. Releasing the BEND key will
not change the display. The prior screen will
return when the bend angle equals the angle in
memory.
12. Pressing UNLOAD will run the bender backwards
so the conduit can be removed. Releasing the
UNLOAD key will stop operation. The UNLOAD key
will not function if the conduit size and type have not
been selected, or when the roller support locking
cam is activated.
13. Pressing JOG will run the bender forward 1/2
degree every time it is pressed unless the maximum
shoe rotation has been reached. JOG will not
operate when the maximum shoe rotation has been
reached. If the conduit size and type have not been
selected, then the SELECT CONDUIT SIZE screen
will be displayed and the bender will not start.
14. Pressing RESET:
a. returns the display to the SELECT CONDUIT
SIZE screen, clears all previous settings (except
Accuracy Adjust Angles) from memory and
clears the screen except for the prompt.
b. will exit Accuracy Adjust mode without saving
any change to the accuracy adjust angle.
15. Pressing CLEAR NUMBER:
a. will eliminate any numerical value you are in the
process of entering.
b. when in Accuracy Adjust mode will set the
adjust angle to zero.
c. will have no effect if you are not being prompted
to enter a number value.
16. Pressing a second key while a first key is already
depressed will do nothing further. The first key
pressed has priority.
12 4455 Boeing Dr., Rockford, IL 61109-2988 815/397-7070