Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Dahua DH-SD29204T-GN
Summary of Contents for Dahua DH-SD29204T-GN
- Page 1 IR Intelligent Speed Dome Installation Manual Version 1.0.0...
-
Page 2: Table Of Contents
Table of Contents INTELLIGENT SPEED DOME INSTALLATION PREPARATION ....... 1 Basic Requirement ..........................1 Check installation space and installation location intension ............1 Please keep all package material well for future use ............... 1 SETUP BEFORE INSTALLATION ..............2 Check Accessories ..........................2 Open Device ............................ - Page 3 Installation ............................... 6 4.2.1 Installation Requirements ........................ 6 4.2.2 Installation Steps ..........................6 APPENDIX Ⅰ LIGHTENING PROTECTION AND SURGE PROTECTION ..10 APPENDIX Ⅱ 24V AC WIRE GAUGE AND TRANSMISSION DISTANCE RELATIONSHIP SHEET ..................11 APPENDIX Ⅲ 12V DC WIRE GAUGE AND TRANSMISSION DISTANCE RELATIONSHIP SHEET ..................
- Page 4 Welcome Thank you for purchasing our speed dome! Please read the following safeguards and warnings carefully before you install or use the product!
- Page 5 Important Safeguards and Warnings Safety Measures 1. Qualified Engineer Needed The installation engineer or maintenance engineer shall have corresponding CCTV system installation certificate or maintenance qualification certificate. The installation engineer or maintenance engineer shall have qualification certificate for work at height.
- Page 6 All the examination and repair work should be done by the qualified service engineers. We are not liable for any problems caused by unauthorized modifications or attempted repair. Note Safety Transportation Heavy stress, violent vibration or water splash are not allowed during transportation, storage and installation.
- Page 7 Do not use gasoline, dope thinner or other chemical material to clean the shell. It may result in shell transfiguration or paint flake. Do not allow the plastic or rubber material to touch the shell for a long time. It may result in paint flake.
-
Page 8: Intelligent Speed Dome Installation Preparation
1 INTELLIGENT SPEED DOME INSTALLATION PREPARATION 1.1 Basic Requirement All installation and operation here should conform to your local electrical safety codes. Before installation, please open the package and check all the components are included. Please make sure the speed dome installation environment and installation mode can meet your requirement. -
Page 9: Setup Before Installation
2 SETUP BEFORE INSTALLATION 2.1 Check Accessories Before the installation, please check the accessories one by one according to the packing list. Please make sure all the components listed are included. 2.2 Open Device Remove the package and then take out the device. Please remove the dustproof feet mat from the pedestal. -
Page 10: Tf Card Slot And Reset Button
Figure 2-2 2.4 TF Card Slot and Reset Button TF card slot and RESET button is shown as in Figure 2-3. Press the RESET button for at least five seconds; you can restore factory default setup. Press the WPS button on the speed dome and the router at the same time. The speed dome can automatically connect to the network. -
Page 11: Ceiling Installation
3 CEILING INSTALLATION 3.1 Installation Components The ceiling installation dome body is shown as in Figure 3-1. Figure 3-1 3.2 Ceiling Installation Steps 3.2.1 Installation Requirements The ceiling mount speed dome can be installed in the hard construction wall in the indoor environments. - Page 12 Figure 3-2 In Figure 3-3, line up the three quick installation screws at the bottom of the pedestal and the concave to the three holes and the U slot at the sheet metal respectively. Turn counter clockwise to secure the speed dome and the sheet metal closely. Note When the arrow of the ceiling installation position turns to the character “open”...
-
Page 13: Wall Mount Bracket Installation
4 WALL MOUNT BRACKET INSTALLATION 4.1 Component Installation Wall mount bracket is shown as below. See Figure 4-1. Figure 4-1 4.2 Installation 4.2.1 Installation Requirements The wall mount speed dome can be installed in the hard construction wall in the indoor environments. - Page 14 Figure 4-2 2). Connect the hanging mount to the internal thread of the wall mount bracket. Secure screws to the right side of the wall mount bracket to secure the hanging mount. Please note this step is very important. Please make sure the screws are firm, otherwise, it may result in falling risk of the intelligent speed dome.
- Page 15 wall mount bracket and pull it out of the other end of the wall mount bracket. Line up the three quick installation screws at the bottom of the pedestal and the concave to the three holes and the U slot at the sheet metal respectively. Turn counter clockwise to secure the speed dome and the sheet metal closely.
- Page 16 Figure 4-5...
-
Page 17: Appendix Ⅰ Lightening Protection And Surge Protection
5 APPENDIX Ⅰ LIGHTENING PROTECTION AND SURGE PROTECTION This series speed dome adopts TVS lighting protection technology. It can effectively prevent damages from various pulse signals below 4000W, such as sudden lighting and surge. While maintaining your local electrical safety code, you still need to take necessary precaution measures when installing the speed dome in the outdoor environment. -
Page 18: Appendix Ⅱ 24V Ac Wire Gauge And Transmission Distance
6 APPENDIX Ⅱ 24V AC WIRE GAUGE AND TRANSMISSION DISTANCE RELATIONSHIP SHEET It is the recommended transmission distance when the cable diameter is fixed and the 24V AC power consumption is below 10%. For the AC device, the max permission voltage power consumption is 10%. -
Page 19: Appendix Ⅲ 12V Dc Wire Gauge And Transmission Distance
7 APPENDIX Ⅲ 12V DC WIRE GAUGE AND TRANSMISSION DISTANCE RELATIONSHIP SHEET The recommended max transmission distance is under the following environments: The wire diameter is fixed and the DC 12V power voltage loss rate is below 10%. For the device of DC power supplying, the max allowed voltage loss rate is 10%. -
Page 20: Appendix Ⅳ Wire Gauge Reference Sheet
8 APPENDIX Ⅳ WIRE GAUGE REFERENCE SHEET Metric bare wire Bare wire cross diameter section （mm） （mm ） 0.050 0.00196 0.060 0.00283 0.070 0.00385 0.080 0.00503 0.090 0.00636 0.100 0.00785 0.110 0.00950 0.130 0.01327 0.140 0.01539 0.160 0.02011 0.180 0.02545 0.200 0.03142 0.230... - Page 21 owners. If there is any uncertainty or controversy, please refer to the final explanation of us. Please visit our website or contact your local service engineer for more information.