Output 5/5 Screen; Uhd Crop 1/2 Screen - Panasonic AW-UE100WP Operating Instructions Manual

Camera menu items (continued)

Output 5/5 screen

O u t p u t 5 /5
O S D O f f Wit h R- Tally
O S D S t a t us
T a l l y
T a l l y B r igh tnes s
S t a t u s L amp
E x t e r n a l Ou tput
O u t p u t 1
O u t p u t 2
R e t u r n
OSD Off With R‑Tally [Off, On]
Off or on the function that turns off camera menu, status, crop frame
and other displays when red tally signals are received via commands
or contacts.
When the red tally signal releases, the camera menu display will
return.
OSD Status [Off, On]
Turn the status display during AWB and ABB off/on, or error display
when an error occurs.
Tally
[Enable, Disable]
[Disable] or [Enable] is set here for the function which turns on or
turns off the tally lamp using the tally control signal.
Tally Brightness [Low, Mid, High]
Adjust the brightness of the tally LED.
Status Lamp
[Enable, Disable]
[Disable] or [Enable] is set here for the status display lamp.
When you want the status display lamp to stay off while this unit is in
operation, set to [Disable].
<NOTE>
• Even when set to [Disable], the status display lamp may light
up when this unit is starting up, updating firmware, or trouble is
occurring.
External Output
Select the signal type output from the External Output signal lines
(Output1, Output2) of the RS‑422 connector. (→ page 18)
Output1 [Off, R‑Tally, G‑Tally]
Output2 [Off, R‑Tally, G‑Tally]
Off Signal is not output.
R-Tally The reception status of the red tally signal is output.
G-Tally The reception status of the green tally signal is output.
Return
Return to the previous menu level.

UHD Crop 1/2 screen

Off
Off
Enable
Low
Enable
Off
Off
3G SDI Out [Full, Crop]
Make the settings for Full/Crop for images output to the 3G SDI OUT
connector.
Full
Crop
This is only enabled when [UHD Crop] is set to [Crop(1080)] or
[Crop(720)].
NDI Out [Full, Crop]
Makes the settings for Full/Crop for images output to NDI
transmission (LAN connector).
Full
Crop
This is only enabled when [UHD Crop] is set to [Crop(1080)] or
[Crop(720)].
IP Out1 [Full, Crop]
IP Out2 [Full, Crop]
Makes the settings for Full/Crop for images output to H.264/H.265/M-
JPEG transmission (LAN connector).
Setting specified in [IP Out1] is applied to images transmitted by each
transmission CH1(H.264(1), H.265(1), JPEG(1)).
Setting specified in [IP Out2] is applied to images transmitted by each
transmission CH2 to CH4(H.264(2) to (4), H.265(2) to (4), JPEG(2)
to (3)).
Full
Crop
This is only enabled when [UHD Crop] is set to [Crop(1080)] or
[Crop(720)].
When the [Streaming mode] on the web screen is [NDI|HX], [IP Out1]
and [IP Out2] will have a linked operation.
70
U H D C r o p 1 / 2
3 G S D I O u t
N D I O u t
I P O u t 1
I P O u t 2
C r o p M a r k e r
R e t u r n
FHD down-converted images are output as is without
cropping UHD images.
Images with FHD cropped from UHD images are output.
The images output in this case are those with the crop
frame specified in [Crop Out].
FHD down-converted images are output as is without
cropping UHD images.
Images with FHD cropped from UHD images are output.
The images output in this case are those with the crop
frame specified in [Crop Out].
FHD down-converted images are output as is without
cropping UHD images.
Images with FHD cropped from UHD images are output.
The images output in this case are those with the crop
frame specified in [Crop Out].
C r o p
C r o p
C r o p
C r o p
Y L + G + M G