Related Manuals for NETGEAR GS110
Summary of Contents for NETGEAR GS110
- Page 1 User Manual 8-Port Gigabit Ethernet Smart Managed Plus Switch with 2-Port 10G/Multi-Gig Uplinks Model GS110EMX NETGEAR, Inc. October 2018 350 E. Plumeria Drive 202-11810-04 San Jose, CA 95134, USA...
- Page 2 Do not use this device outdoors. If you connect cables or devices that are outdoors to this device, see http://kb.netgear.com/000057103 for safety and warranty information. Trademarks © NETGEAR, Inc., NETGEAR, and the NETGEAR Logo are trademarks of NETGEAR, Inc. Any non-NETGEAR trademarks are used for reference purposes only. Revision History...
-
Page 3: Table Of Contents
Connection.................21 Set Up a Fixed IP Address for the Switch by Connecting Directly to the Switch Off-Network............22 Use the NETGEAR Insight Mobile App to Access the Switch..24 Use the NETGEAR ProSAFE Plus Utility to Access the Switch..25 Change the Password................26 Register Your Product................27... - Page 4 Use the ProSAFE Plus Utility to Specify the Switch IP Address.50 Manage Switch Discovery Protocols..........50 Manage Universal Plug and Play..........51 Manage Bonjour................52 Manage NETGEAR Switch Discovery Protocol......52 Manage Multicast Traffic With IGMP Snooping......53 Customize IGMP Snooping............54 Specify a VLAN for IGMP Snooping..........55 Set Up Link Aggregation..............56...
- Page 5 8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX Chapter 7 Diagnostics and Troubleshooting Test Cable Connections..............74 Resolve a Subnet Conflict to Access the Switch......74 Hardware Troubleshooting Chart............75 Appendix A Factory Default Settings and Technical Specifications Factory Default Settings..............78 Basic Technical Specifications............79 Appendix B Mount the Switch Attach the Switch to a Wall..............82 Install the Switch in a Rack..............82...
-
Page 6: Chapter 1 Hardware Overview Of The Switch
Gbps, 2.5 Gbps, 5 Gbps or 10 Gbps connectivity. You can manage the switch over the local browser–based management interface that you can access from a computer or from a smartphone on which the NETGEAR Insight app is installed. You can optimize Quality of Service (QoS) and set up prioritization and rate limiting for individual ports. -
Page 7: Related Documentation
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX Related Documentation The following related documentation is available at downloadcenter.netgear.com: • Installation guide • Data sheet • ProSAFE Plus Configuration Utility User Manual Switch Package Contents Figure 1. Switch package contents The package contains the following items: •... -
Page 8: Front Panel
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX Front Panel Figure 2. Front panel The following table lists the front panel components from left to right. Table 1. Front panel components Letter Description Power LED Factory Defaults button (see Use the Factory Defaults Button to Reset the Switch on page 69) Eight RJ-45 Gigabit Ethernet ports numbered 1 through 8 that support 1G, 100M, and 10M Two RJ-45 10-Gig/Multi-Gig Ethernet ports numbered 9 and 10 that support 10G, 5G, 2.5G, 1G, and 100M... -
Page 9: Status Leds
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX Status LEDs Status LEDs are located on the front panel of the switch. Each port provides a left LED and a right LED that, in combination, indicate speed and activity. Table 2. LED descriptions Left Right Description... - Page 10 8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX Table 2. LED descriptions (Continued) Left Right Description Port LEDs for ports Green Green Both LEDs solid green. A 10G link with a powered-on device is 9 and 10 detected. Both LEDs blinking green. Traffic is detected on the 10G link. Green Left LED solid green, right LED off.
-
Page 11: Back Panel
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX Back Panel Figure 3. Back panel The back panel of the switch provides a Kensington lock slot for an optional lock and the 12V, 12.5A DC connector for the power adapter. Switch Label The switch label on the bottom panel of the switch shows the serial number, MAC address, default login information, and other information for the switch. -
Page 12: Safety Instructions And Warnings
Any device that is located outdoors and connected to this product must be properly grounded and surge protected. To the extent permissible by applicable law, failure to follow these guidelines can result in damage to your NETGEAR product, which might not be covered by NETGEAR’s warranty. • Observe and follow service markings: Do not service any product except as explained in your system documentation. - Page 13 8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX • Allow the product to cool before removing covers or touching internal components. • Operate the product only from the type of external power source indicated on the electrical ratings label. If you are not sure of the type of power source required, consult your service provider or local power company.
-
Page 14: Chapter 2 Install And Access The Switch In Your Network
• Methods to Discover and Access the Switch • Access the Switch and Discover the IP Address of the Switch • Use the NETGEAR Insight Mobile App to Access the Switch • Use the NETGEAR ProSAFE Plus Utility to Access the Switch •... -
Page 15: Set Up The Switch In Your Network And Power On The Switch
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX Set Up the Switch in Your Network and Power On the Switch Before you set up the switch in your network, we recommend that you review the information in the following table, which describes the network cables that you can use for the switch connections and the speeds that these cables can support, up to 100 meters (328 feet). - Page 16 8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX Table 4. Figure components Letter Description Letter Description GS110EMX switch Computer 10G aggregation switch WiFi access point Network router 10G NAS device Internet Note: Red lines indicate 10G connections. Black lines indicate 1G connections.
-
Page 17: Methods To Discover And Access The Switch
• Insight mobile app. Install the NETGEAR Insight mobile app on a smartphone or tablet to discover the switch in your network and access the local browser interface of the switch (see Use the NETGEAR Insight Mobile App to Access the Switch on page 24). -
Page 18: Access The Switch From A Mac Using Bonjour
If your Mac supports Bonjour, you can use the following procedure. If your Mac does not support Bonjour, see Access the Switch From a Mac or Windows-Based Computer Using the NETGEAR Switch Discovery Tool on page 19. To access the switch from a Mac using Bonjour and discover the switch IP address: 1. -
Page 19: Access The Switch From A Mac Or Windows-Based Computer Using The Netgear Switch Discovery Tool
Access the Switch From a Mac or Windows-Based Computer Using the NETGEAR Switch Discovery Tool The NETGEAR Switch Discovery Tool lets you discover the switch in your network and access the local browser interface of the switch from a Mac or a 64-bit Windows-based computer. - Page 20 Layer 2 network. 7. Open the Switch Discovery Tool. If the NETGEAR Switch Discovery Tool icon is in the Dock of your Mac or on the desktop of your Windows-based computer, click or double-click the NETGEAR Switch Discovery Tool icon to open the program.
-
Page 21: Set Up A Fixed Ip Address For The Switch
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX Set Up a Fixed IP Address for the Switch By default, the switch receives an IP address from a DHCP server (or a router that functions as a DHCP server) in your network. However, the DHCP server might not always issue the same IP address to the switch. -
Page 22: Set Up A Fixed Ip Address For The Switch By Connecting Directly To The Switch Off-Network
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX 6. Enter the fixed (static) IP address that you want to assign to the switch and the associated subnet mask and gateway IP address. You can also either leave the address in the IP Address field as it is (with the IP address that was issued by the DHCP server) or change the last three digits of the IP address to an unused IP address. - Page 23 8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX The default password is password. The password is case-sensitive. The Switch Information page displays. 6. From the DHCP Mode menu, select Disable. The IP address fields become available. 7. Enter the fixed (static) IP address that you want to assign to the switch and the associated subnet mask and gateway IP address.
-
Page 24: Use The Netgear Insight Mobile App To Access The Switch
To access the switch from the Insight app: 1. On your iOS or Android mobile device, go to the app store, search for NETGEAR Insight, and download and install the app. -
Page 25: Use The Netgear Prosafe Plus Utility To Access The Switch
Use the NETGEAR ProSAFE Plus Utility to Access the Switch The NETGEAR ProSAFE Plus Utility runs on Windows-based computers and lets you customize and manage the switch for your network. For easiest access, we recommend that you cable the switch to a network with a router or DHCP server that assigns IP addresses, power on the switch, and then use a computer that is connected to the same network as the switch. -
Page 26: Change The Password
For a description of ProSAFE Plus Utility features, see the ProSAFE Plus Utility User Manual. You can access the user manual through links on the Help tab of the utility, or you can download it by visiting downloadcenter.netgear.com. Change the Password The default password to access the switch is password. -
Page 27: Register Your Product
Register Your Product We recommend that you use the NETGEAR Insight mobile app to register your product (see Use the NETGEAR Insight Mobile App to Access the Switch on page 24). Registering your product allows you to receive email alerts and streamlines the technical support process. - Page 28 8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX 7. Follow the onscreen process to register your product. Install and Access the Switch in User Manual Your Network...
-
Page 29: Chapter 3 Use Vlans For Traffic Segmentation
Use VLANS for Traffic Segmentation This chapter describes how you can use VLANs to segment traffic on the switch. The chapter contains the following sections: • VLAN Overview • Create Basic Port-Based VLANs • Assign Ports to Multiple Port-Based VLANs •... -
Page 30: Vlan Overview
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX VLAN Overview Virtual LANs (VLANs) are made up of networked devices that are grouped logically into separate networks. You can group ports on a switch to create a virtual network made up of the devices connected to the ports. -
Page 31: Assign Ports To Multiple Port-Based Vlans
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX 5. Select VLAN. The Basic Port-based VLAN Status page displays. 6. If this is the first time that you are accessing this page or if you are changing the VLAN assignment method, select the Enable radio button and continue with Step Otherwise, see Step 9. - Page 32 8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX 3. In the address field of your web browser, enter the IP address of the switch. The login page displays. 4. Enter the switch password. The default password is password. The password is case-sensitive. The Switch Information page displays.
-
Page 33: Create 802.1Q-Based Vlans In A Basic Configuration
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX Create 802.1Q-Based VLANs in a Basic Configuration A 802.1Q-based VLAN configuration lets you assign ports on the switch to a VLAN with an ID number in the range of 1–4093. By default, all ports are members of VLAN 1. In an advanced 802.1Q-based VLAN configuration, you can set up VLANs to which you can add tagged or untagged ports and you can use port VLAN ID (PVID). -
Page 34: Create 802.1Q-Based Vlans In An Advanced Configuration
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX You can enter a VLAN ID from 1 to 4093. If all the VLANs share an uplink to the Internet or servers, enter all in the VLAN ID field for the port that you want to use for the uplink. -
Page 35: Add Tagged Or Untagged Ports To An 802.1Q-Based Vlan
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX 7. Click the OK button. The pop-up window closes. 8. Click the Apply button. Your settings are saved. The VLAN Identifier Setting table displays. 9. In the VLAN ID field, enter a VLAN ID. You can enter a VLAN ID from 1 to 4093. - Page 36 8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX The login page displays. 4. Enter the switch password. The default password is password. The password is case-sensitive. The Switch Information page displays. 5. Select VLAN > 802.1Q > Advanced > VLAN Configuration. The Advanced 802.1Q VLAN Status page displays.
-
Page 37: Specify A Port Pvid For An 802.1Q-Based Vlan
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX Specify a Port PVID for an 802.1Q-Based VLAN A default port VLAN ID (PVID) is a VLAN ID tag that the switch assigns to data packets it receives that are not already addressed (tagged) for a particular VLAN. For example, if you connected a computer on port 6 and you want it to be a part of VLAN 2, configure port 6 to automatically add a PVID of 2 to all data received from the computer. -
Page 38: Manage The Voice Vlan
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX Manage the Voice VLAN The switch supports a voice VLAN to facilitate voice over IP (VoIP) traffic. You can configure the voice VLAN only if you enable the 802.1Q VLAN mode (see Create 802.1Q-Based VLANs in a Basic Configuration on page 33 or Create 802.1Q-Based VLANs in an Advanced Configuration on page 34). -
Page 39: Enable The Voice Vlan Mode For Ports
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX You can select either the default VLAN ID (1) or a VLAN ID that you manually added (see Create 802.1Q-Based VLANs in a Basic Configuration on page 33 or Create 802.1Q-Based VLANs in an Advanced Configuration on page 34). 7. -
Page 40: Manage The Oui Table
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX Manage the OUI Table The switch includes default Organizationally Unique Identifiers (OUIs), which are associated with VoIP phones of specific manufacturers. All traffic received on voice VLAN ports from VoIP phones with a listed OUI is forwarded on the voice VLAN. You can add and remove OUIs. - Page 41 8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX • To change an existing OUI prefix in the table, do the following: a. Select the OUI. b. Change the OUI in the Telephony (OUIs) field, change the description in the Description field, or change both.
-
Page 42: Chapter 4 Optimize Performance With Quality Of Service
Optimize Performance With Quality of Service This chapter covers the following topics: • Enable 802.1p/DSCP-Based Quality of Service • Configure Port-Based Quality of Service • Set Up Rate Limiting • Set Up Broadcast Filtering... -
Page 43: Enable 802.1P/Dscp-Based Quality Of Service
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX Enable 802.1p/DSCP-Based Quality of Service 802.1p/DSCP-based priority uses a field in the data packet header that identifies the class of data in the packet (for example, voice or video). When 802.1p/DSCP-based priority is used, the switch reads information in the packet header to determine the priority to assign to the packet. -
Page 44: Configure Port-Based Quality Of Service
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX Configure Port-Based Quality of Service You can assign a priority to all data passing through a particular port. Data with a higher priority is transmitted faster. If packets arrive at several ports at the same time, the ports configured as higher priority transmit their packets first. -
Page 45: Set Up Rate Limiting
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX 10. To set a different port priority for one or more other ports, repeat Step 9. Set Up Rate Limiting You can limit the rate at which the switch accepts incoming data and the rate that it retransmits outgoing data. -
Page 46: Set Up Broadcast Filtering
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX Set Up Broadcast Filtering You can configure the switch to block broadcast storms (massive transmission of broadcast packets forwarded to every port on the same VLAN). If they are not blocked, broadcast storm packets can delay or halt the transmission of other data. - Page 47 8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX 9. To set a different rate for one or more other ports, repeat Step 8. Optimize Performance With User Manual Quality of Service...
-
Page 48: Chapter 5 Manage Network Settings
Manage Network Settings This chapter contains the following sections: • Specify IP Address Settings for the Switch • Manage Switch Discovery Protocols • Manage Multicast Traffic With IGMP Snooping • Set Up Link Aggregation... -
Page 49: Specify Ip Address Settings For The Switch
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX Specify IP Address Settings for the Switch By default, the switch IP address works as follows: • If you cable the switch to a network with a DHCP server before you power on the switch, the DHCP server assigns an IP address to the switch when the switch is powered on. -
Page 50: Use The Prosafe Plus Utility To Specify The Switch Ip Address.50
The ProSAFE Plus Utility runs on Windows-based computers. You can install the utility to select additional options to manage and customize the switch for your network. To download the utility, visit netgear.com/support/product/PCU. You must use ProSAFE Plus Utility version 2.5.3 or a later version. -
Page 51: Manage Universal Plug And Play
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX Bonjour, and NETGEAR Switch Discovery Protocol (NSDP), which are protocols that can discover the switch. A device that functions in the same network as the switch and that supports one of these protocols can discover the switch and obtain the IP address. -
Page 52: Manage Bonjour
Your settings are saved. Manage NETGEAR Switch Discovery Protocol A NETGEAR device or application that supports NETGEAR Switch Discovery Protocol (NSDP) can discover the switch in the network so that you can find the switch IP address and log in to the local browser interface of the switch. NSDP is enabled by default. You can disable NSDP for security reasons. -
Page 53: Manage Multicast Traffic With Igmp Snooping
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX To manage NSDP: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired network connection, or connect directly to a switch that is off-network using an Ethernet cable. 2. -
Page 54: Customize Igmp Snooping
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX Customize IGMP Snooping By default, IGMP snooping is enabled. You can customize the settings for your network. To customize IGMP snooping: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired network connection, or connect directly to a switch that is off-network using an Ethernet cable. -
Page 55: Specify A Vlan For Igmp Snooping
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX 10. (Optional) Select an option from the IGMP Snooping Static Router Port menu. You can select a port to be the dedicated IGMP snooping static router port if no IGMP query exists in the network for the switch to discover the router port dynamically. -
Page 56: Set Up Link Aggregation
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX Your settings are saved. Set Up Link Aggregation Link aggregation groups (LAGs) allow you to combine multiple Ethernet links into a single logical link. Network devices treat the aggregation as if it were a single link, which increases fault tolerance and load sharing. -
Page 57: Set Up A Link Aggregation Control Protocol Group
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX The default password is password. The password is case-sensitive. The Switch Information page displays. 5. Select System > LAG > LAG Membership. The LAG Membership page displays. 6. In the LAG ID menu, select the LAG ID. You can select a LAG ID from 1 to 5. - Page 58 8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX To specify an LACP group: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired network connection, or connect directly to a switch that is off-network using an Ethernet cable.
-
Page 59: Set Up The Lacp System Priority For The Switch
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX e. Click the Apply button. Your settings are saved. Set Up the LACP System Priority for the Switch The LACP system priority specifies the link aggregation priority of the switch relative to the devices at the other ends of the links on which link aggregation is enabled. - Page 60 8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX To specify LACP port priority value and LACP time-out value for a port: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired network connection, or connect directly to a switch that is off-network using an Ethernet cable.
-
Page 61: Chapter 6 Manage And Monitor The Switch
Manage and Monitor the Switch This chapter covers the following topics: • Manage Flow Control • Manage the Port Speed and the Port Status • Enable Loop Prevention • Manage the Power Saving Mode • Manually Download and Upgrade the Firmware •... -
Page 62: Manage Flow Control
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX Manage Flow Control Flow control works by pausing a port if the port becomes oversubscribed and dropping all traffic for small bursts of time during the congestion condition. You can enable or disable IEEE 802.3x flow control. - Page 63 8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX To manage the port speed and the port status and add a port description: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired network connection, or connect directly to a switch that is off-network using an Ethernet cable.
-
Page 64: Enable Loop Prevention
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX Enable Loop Prevention If loop prevention is enabled and the switch detects a loop, the switch blocks one of the ports that are part of the loop and both LEDs of that port blink at a constant speed. If two ports are part of a loop, the port with the highest port number is blocked. -
Page 65: Manually Download And Upgrade The Firmware
You can manually check for the latest firmware version for your switch by visiting netgear.com/support/download/. To manually download and upgrade the firmware: 1. Visit netgear.com/support/download/. 2. Enter your product model number in the Enter a Product Name/Model Number field, search by clicking the magnifying glass, and locate the firmware for your switch. -
Page 66: Reboot The Switch
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX You can use a WiFi or wired network connection, or connect directly to a switch that is off-network using an Ethernet cable. 6. Launch a web browser. 7. In the address field of your web browser, enter the IP address of the switch. The login page displays. -
Page 67: Save The Switch Configuration
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX 5. Select System > Maintenance > Device Reboot. The Device Reboot page displays. 6. Select the check box. 7. Click the Apply button. The switch reboots. Save the Switch Configuration You can save the switch configuration as a file. We recommend that you save the configuration. -
Page 68: Return The Switch To Its Factory Default Settings
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX To restore the switch configuration that you saved: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired network connection, or connect directly to a switch that is off-network using an Ethernet cable. -
Page 69: Use The Factory Defaults Button To Reset The Switch
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX Use the Factory Defaults Button to Reset the Switch You can use the Factory Defaults button to reset the switch to its factory default settings. Caution: This process erases all settings that you configured on the switch. To reset the switch to factory default settings using the Factory Defaults button: 1. -
Page 70: Enable Port Mirroring
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX 6. Select the check box. 7. Click the Apply button. The switch returns to its factory default settings. The switch restarts to load the restored configuration. Warning: Do not interrupt the network connection or power to the switch during the reset process. -
Page 71: View Switch Information Or Change The Switch Device Name
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX By default, mirroring is disabled. 9. Click the Apply button. Your settings are saved. View Switch Information or Change the Switch Device Name You can view the switch product name (model), serial number, MAC address, firmware version, DHCP mode, and other network information. - Page 72 8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX To view or clear the port statistics: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired network connection, or connect directly to a switch that is off-network using an Ethernet cable.
-
Page 73: Chapter 7 Diagnostics And Troubleshooting
Diagnostics and Troubleshooting This chapter contains the following sections: • Test Cable Connections • Resolve a Subnet Conflict to Access the Switch • Hardware Troubleshooting Chart... -
Page 74: Test Cable Connections
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX Test Cable Connections You can use the cable diagnostic feature to easily find out the health status of network cables. If any problems exist, this feature helps quickly locate the point where the cabling fails, allowing connectivity issues to be fixed much faster, potentially saving technicians hours of troubleshooting. -
Page 75: Hardware Troubleshooting Chart
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX be different from the subnet used in your network. You might see the following message if you try to use the ProSAFE Plus Utility to access the switch: The switch and manager IP address are not in the same subnet. To resolve this subnet conflict: 1. - Page 76 8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX Table 5. Troubleshooting chart (Continued) Symptom Possible Cause Possible Solution A segment or device is not One or more devices are not Verify that the cabling is correct. recognized as part of the properly connected, or cabling Make sure that all connectors are securely network.
-
Page 77: Appendix A Factory Default Settings And Technical Specifications
Factory Default Settings and Technical Specifications This appendix includes the following sections: • Factory Default Settings • Basic Technical Specifications... -
Page 78: Factory Default Settings
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX Factory Default Settings You can return the switch to its factory settings. Use the end of a paper clip or some other similar object to press and hold the Factory Defaults button on the front panel of the switch for four seconds. -
Page 79: Basic Technical Specifications
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX Basic Technical Specifications The following table shows the basic technical specifications of the switch. For more specifications, see the data sheet that you can download by visiting downloadcenter.netgear.com. Table 7. Basic technical specifications Feature Description IEEE standards IEEE 802.3 Ethernet... - Page 80 8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX Table 7. Basic technical specifications (Continued) Feature Description Storage humidity 95% maximum relative humidity, noncondensing Storage altitude 10,000 ft (3,000 m) maximum Regulatory compliance BSMI, CB, CE, CCC, FCC, ISED, KC, RCM, VCCI EMC Class B Factory Default Settings and User Manual...
-
Page 81: Appendix B Mount The Switch
Mount the Switch This appendix includes the following sections: • Attach the Switch to a Wall • Install the Switch in a Rack... -
Page 82: Attach The Switch To A Wall
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS110EMX Attach the Switch to a Wall The switch provides two mount holes on the bottom panel so that you can attach the switch to a wall. The switch package provides two screws and anchors for that purpose. To attach the switch to a wall: 1.