NETGEAR, Inc. Technical Support Thank you for choosing NETGEAR. To register your product, get the latest product updates, get support online, or for more information about the topics covered in this manual, visit the Support website at http://support.netgear.com...
About This Manual The NETGEAR ® ProSafe GS110T Hardware Installation Guide describes how to install and power on the GS110T Smart Switch. The information in this manual is intended for readers with intermediate computer and Internet skills. Conventions, Formats, and Scope...
DANGER: This is a safety warning. Failure to take heed of this notice may result in personal injury or death. • Scope. This manual is written for the GS110T Smart Switch according to these specifications: Product Version GS110T Smart Switch...
GS110T Smart Switch. The GS110T Smart Switch is a supplement to the Gigabit Advanced Smart Switch family. Available as a desktop or wall-mountable switch, the GS110T Smart Switch is not intended to be rack-mountable.The GS110T is non-PoE supportable low-port switch with two fiber uplinks included.
The maximum segment length is 328 feet (100 meters) over Category 5 Unshielded Twisted-Pair (UTP) cable. Features The following list identifies the key features of the GS110T Smart Switch: • Eight RJ-45 10/100/1000 Mbps autosensing Gigabit Ethernet switching ports.
• Wall mounting screws (2) • External power adapter • Installation guide • Smart Switch Resource CD with the Netgear Smart Control Center and User’s manual If any item is missing or damaged, contact the place of purchase immediately. Introduction...
Device Hardware Interfaces GS110T Front-Panel Configuration The GS110T has eight 10/100/1000 Mbps autosensing and two 1000 Mbps SFP Gigabit Ethernet switching ports. Each RJ-45 port is capable of sensing the line speed and negotiating the duplex mode with the link partner automatically.
Power Connector Figure 3. GS110T Back Panel The back panel contains the following: • External 12V/1A power adapter for the GS110T LED Designations Port LEDs Table 1 describes the RJ-45 and SFP port LED designations. There are two LEDs for each RJ-45 port.
NETGEAR GS110T Smart Switch System LEDs Table 2 describes the system LED designations. Table 2. System LEDs Designation Power/Status LED • Solid Green = Power is supplied to the switch and the switch is operating normally. • Solid Yellow = The switch is booting.
NETGEAR GS110T Smart Switch Factory Defaults Button The Smart Switch has a Factory Defaults button on the front panel so that you can remove the current configuration and return the device to its factory settings. When you enable the Factory Defaults button, all settings including the password, VLAN settings, and port configurations are removed.
1000 Mbps hubs and switches. Desktop Switching The GS110T Smart Switch can be used as a desktop switch to build a small network that enables users to have 1000 Mbps access to a file server. With full-duplex enabled, the switch port connected to the server or PC can provide 2000 Mbps throughput.
Installation This chapter describes the installation procedures for your NETGEAR GS110T Smart Switch. Switch installation involves the following steps: Step 1: Preparing the Site Step 2: Installing the Switch Step 3: Checking the Installation Step 4: Connecting Devices to the Switch...
Step 2: Installing the Switch The GS110T Smart Switch can be used on a flat surface or mounted on the wall. Installing the Switch on a Flat Surface The switch ships with four self-adhesive rubber footpads. Stick one rubber footpad on each of the four concave spaces on the bottom of the switch.
Step 4: Connecting Devices to the Switch The following procedure describes how to connect PCs to the switch’s RJ-45 ports. The GS110T Smart Switch contains Auto Uplink technology, which allows the attaching of devices using either straight-through or crossover cables.
Step 6: Managing the Switch using a Web Browser or the PC Utility The GS110T Smart Switch contains software for viewing, changing, and monitoring the way it works. This management software is not required for the switch to work. The ports can be used without using the management software.
Troubleshooting This chapter provides information about troubleshooting the NETGEAR Smart Switch. Topics include the following: • Troubleshooting Chart • Additional Troubleshooting Suggestions Troubleshooting Chart The following table lists symptoms, causes, and solutions of possible problems. Table 4. Troubleshooting Chart Symptom...
AC power from the switch and then reapply AC power. If the problem continues, contact NETGEAR technical support. In North America, call 1-888-NETGEAR. If you are outside of North America, please refer to the support information card included with your product.
NETGEAR GS110T Smart Switch IP and MAC ACL Green feature (Auto power down and Short cable power saving) DoS protection Interface Eight RJ-45 connectors for 10BASE-T, 100BASE-TX, and 1000BASE-T (Auto Uplink™ on all ports) Two SFP slots for SFP modules...
NETGEAR GS110T Smart Switch Electromagnetic Emissions FCC Class B CE Class B: Includes EN55022 (CISPR 22), 55024, and 50082-1 VCCI Class B C-Tick Safety UL/cUL CE (includes EN60950) Technical Specifications...
Low Latency Connecting Devices to the Switch Copper Crossover Media Access Control Default IP Address Default Reset Button Netgear Smart Control Center Utility Desktop Switching Device Hardware Interfaces Duplex Mode Operating Conditions Operating Environment Operating humidity Example of Desktop Switching...
Page 28
NETGEAR GS110T Smart Switch Rack-mount Kit Reset Button RJ-45 RJ-45 Ports Rubber footpads Site Requirements Smart Switch Resource CD Straight-through System LEDs technical support Temperature trademarks Traffic Control Troubleshooting Chart User Intervention User’s Manual Ventilation VLAN Web-based Graphical User Interface...