Subscribe to Our Youtube Channel
Related Manuals for Clarke SE15
Summary of Contents for Clarke SE15
- Page 1 AIR COMPRESSOR ELECTRIC MOTOR DRIVEN OPERATION & MAINTENANCE INSTRUCTIONS Original Instructions LS1216...
-
Page 2: Data Table
INTRODUCTION Thank you for purchasing this CLARKE compressor which is designed to supply compressed air to air powered tools for a wide range of applications such as spraying, sanding, drilling, and cutting. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. -
Page 3: Environmental Recycling Policy
GUARANTEE This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase. This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended. -
Page 4: Safety Precautions
SAFETY PRECAUTIONS Before using your compressor it is in your own interest to read and pay attention to the following safety rules: 1. COMPRESSED AIR IS DANGEROUS - Never direct a jet of air at people or animals. 2. Do not operate your air compressor with any guards removed. 3. -
Page 5: Installation
INSTALLATION Before installing your machine, check that its air output is sufficient for the equipment to be used. The air output from the compressor must be more than the volume of air required. We recommend the following: 1. Firm and level site, and the use of floor mountings for stationary compressors - anti-vibration pads. -
Page 6: Electrical Connections
20 amp 30 amp 16 amp 40 amp 20 amp 50 amp 25 amp 30 amp 10.0 25 amp LUBRICATION Pump: Use Clarke compressor oil, as indicated on machine plate. Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 7: Before Starting Compressor, Check
(stamped on machine plate), if the pressure exceeds the maximum working pressure stated, stop the machine (see below), vent the system and contact the Clarke Service Department. TO STOP COMPRESSOR 1. Switch off at the pressure switch (Push knob down or turn switch). -
Page 8: General Arrangement
GENERAL ARRANGEMENT A. STATIONARY Fig.2 NB: Must be mounted on Anti Vibration Pads Illustrative purposes only Air Compressor Pump Inspection Plug – Electric Motor (or Non-Return Valve – Wire Guard Air Bleed Valve Air Delivery Pipe Pressure Switch Oil Drain Plug Air Bleed Pipe Pressure Gauge Saddle... -
Page 9: Outlet Pressure Adjustments
3. Switch on pressure switch (lift knob or twist switch). If the overload trips repeatedly, it may indicate a fault with the compressor, in this case you should contact the Clarke service department. OTHER PRODUCTS WITHIN OUR RANGE In addition to Air Compressors from 3–40 cfm, we offer a vast range of air tools and airline equipment. -
Page 10: Troubleshooting Chart
Relief valve leaking. Clean relief valve or change under pressure pressure switch. switch blows whilst compressor is running Compressor unit Pressure switch defective. Contact Clarke Service will not stop automatically. Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... - Page 11 Thaw non-return valve out revolutions. possibly frozen up. (Unit must be installed in frost- free place). Solenoid valve leaking or Contact Clarke Service defective (only applies to 10 HP machines and above). Fuses keep Inadequate size fuse installed. Replace with reference to blowing.
- Page 12 Leak between compressor block Tighten connection and repair working and air receiver/ leaks in or near leak or Contact Clarke Service pressure air receiver. required. RPM too low because of Contact Clarke Service incorrectly connected electric motor.
- Page 13 Oil level too low (check 2 or 3 Fill with oil - See page 7. times after stopping). Fault in valves (machine not Contact Clarke Service stopping). Blown head gasket (machine not Contact Clarke Service stopping). Dirt on cooling fins or suction filter.
-
Page 14: Maintenance Chart
Check / Replace if necessary Clean Oil breather Check / Clean Fan and cooling fins Clean Inlet and outlet If worn Contact Clarke valves Service department Non Return Valve Clean Replace if worn Belt Tension Check / Does not apply to... -
Page 15: Declaration Of Conformity
DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
Need help?
Do you have a question about the SE15 and is the answer not in the manual?
Questions and answers