Panasonic PT-RW620 Operating Instructions Manual page 131

8) Press asqw to select [COMMAND].
9) Press the <ENTER> button.
f The [COMMAND] detailed screen is displayed.
10) Press as to select a [COMMAND].
f For [COMMAND] which requires detailed settings, the items of the detailed settings will switch each time
you press qw.
f When [INPUT] is selected, press the <ENTER> button, and then press asqw to select the input to be
set.
[COMMAND]
[POWER ON]
[STANDBY]
[QUICK STARTUP]
[SHUTTER]
[INPUT]
[OPERATING MODE]
[P IN P]
*1 Only for PT-RZ770, PT-RZ660
*2 When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the projector, its input
name is automatically reflected from [INPUT1] to [INPUT10]. When an item that does not reflect the input name is selected, it will be disabled.
*3 If you change the settings while using the projector, the duration until the luminance of light source decreases by half may shorten or the
luminance may decrease.
11) Press the <ENTER> button.
f The command is fixed and n is displayed at the left of the selected command.
f After the command is fixed, press the <MENU> button to close the detailed setting screen.
12) Press asqw to select [STORE], and press the <ENTER> button.
Note
f To delete a command that has been already set, press the <DEFAULT> button on the remote control while the screen in Step 5) is
displayed, or select [DELETE] at the screen in Step 6) and press the <ENTER> button.
f If multiple commands have been set for the same time, they are executed in chronological order starting from the smallest command
number.
f The operating time will be the local time. (x page 129)
Chapter 4 Settings — [PROJECTOR SETUP] menu
Detailed settings of
[COMMAND]
―
―
[ON]
[OFF]
[OPEN]
[CLOSE]
[RGB1]
[RGB2]
[DVI-D]
[HDMI]
[DIGITAL LINK]
[SDI]
*1
[INPUT1] - [INPUT10]
[NORMAL]
[ECO]
[LONG LIFE1]
[LONG LIFE2]
*3
[LONG LIFE3]
[USER1]
[USER2]
[USER3]
[OFF]
[USER1]
[USER2]
[USER3]
Switches on the projector.
Enters standby.
Enables the function of the [PROJECTOR SETUP] menu →
[QUICK STARTUP].
Disables the function of the [PROJECTOR SETUP] menu →
[QUICK STARTUP].
Disables the shutter function (shutter: open).
Enables the shutter function (shutter: closed).
Switches the input to RGB1.
Switches the input to RGB2.
Switches the input to DVI-D.
Switches the input to HDMI.
Switches the input to DIGITAL LINK.
Switches the input to SDI.
Switches the input to DIGITAL LINK, and switches the input of the
*2
Panasonic twisted-pair-cable transmitter to the specified input.
Prioritizes luminance.
Controls the power to increase the life of the light source with higher
luminance.
Controls the power to increase the life of the light source although
the luminance is lower than that of [ECO].
Controls the power to increase the life of the light source although
the luminance is even lower than that of [LONG LIFE1].
Controls the power to increase the life of the light source to the
maximum although the luminance is even lower than that of [LONG
LIFE2].
Controls the power with the setting set in [USER1].
Controls the power with the setting set in [USER2].
Controls the power with the setting set in [USER3].
P IN P function is not used.
Places the sub screen with the setting set in [USER1].
Places the sub screen with the setting set in [USER2].
Places the sub screen with the setting set in [USER3].
Description
ENGLISH - 131