Switching The Hdmi Output; Checking Your System Settings; Resetting The System - Pioneer VSX-1326-K Operating Instructions Manual

Switching the HDMI output

VSX-1326 only
Set which terminal to use when outputting
video and audio signals from the HDMI output
terminals.
The HDMI OUT 1 terminal is compatible with
the Control with HDMI function.
% Press to the receiver operation
mode, then press HDMI OUT.
Please wait a while when Please wait ... is
displayed.
The output switches among HDMI OUT ALL,
HDMI OUT 1 and HDMI OUT 2 each time the
button is pressed.
! The synchronized amp mode is canceled
when the HDMI output is switched. If you wish
to use the synchronized amp mode, switch to
HDMI OUT 1, then select the synchronized
amp mode on the TV using the TV's remote
control.

Checking your system settings

Use the status display screen to check your
current settings for features such as surround
back channel processing and your current
MCACC preset.
1 Press to the receiver operation
mode, then press STATUS to check the
system settings.
The front panel display shows each of the fol-
lowing settings for three seconds each: Input
Source d Sampling Frequency d MCACC
preset d ZONE 2 input d ZONE 3 input
(VSX-1326 only) d HDMI OUT (VSX-1326
only).
2 When you're finished, press STATUS
again to switch off the display.

Resetting the system

Use this procedure to reset all the receiver's
settings to the factory default. Use the front
panel controls to do this. Set MULTI-ZONE to
MULTI ZONE OFF.
! Disconnect the iPod and USB memory device
from the receiver beforehand.
! Set the Control with HDMI to OFF (see HDMI
Setup on page 47 ).
1 Switch the receiver into standby.
2 While holding down ENTER on the
front panel, press u STANDBY/ON.
The display shows RESET c NO d.
3 Select 'RESET' using PRESET k/l,
then press ENTER on the front panel.
The display shows RESET? OK.
4 Press ENTER to confirm.
OK appears in the display to indicate that the
receiver has been reset to the factory default
settings.
! Note that all settings will be saved, even if the
receiver is unplugged.
Default system settings
Setting Default
Digital Video Converter ON
SPEAKERS SB/FH
Normal
Speaker System
(SB/FH)
Front SMALL
Center SMALL
FH/FW SMALL
Speaker Setting
Surr SMALL
SB SMALLx2
SW YES
Surround Position IN REAR
Crossover 80 Hz
X-Curve OFF
DIMMER Brightest
Inputs
See Input function default and possible settings on
page 28 .
HDMI
HDMI Audio Amp
VSX-1326 only: HDMI OUT
HDMI output ALL
Control ON
Control Mode PQLS
Display Power Off NO
Audio playback
Power On Level LAST
Volume Limit OFF
Mute Level FULL
Phase Control ON
iPod/USB,
HOME MEDIA
GALLERY, ON
Auto Sound
ADAPTER PORT
Retriever
input function
Other input
OFF
functions
Using other functions
Setting Default
Sound Delay 0.0 frame
Dual Mono CH1
DRC AUTO
SACD Gain 0 dB
LFE Attenuate 0 dB
Auto delay OFF
Digital Safety OFF
ExtendedStereo 90
Effect Level
Other modes 50
Center Width 3
2 PL II Music
Dimension 0
Options
Panorama OFF
Neo:6
CINEMA: 10
Neo:6 Options Center Image
Neo:6
MUSIC: 3
2 PL IIz Options Height Gain MID
Listening Mode AUTO
(2 ch/multi ch) SURROUND
All Inputs
Listening Mode
STEREO
(Headphones)
See also Setting the Audio options on page 50 for
other default DSP settings.
MCACC
M1:
MCACC Position Memory
MEMORY 1
Channel Level (M1 to M6) 0.0 dB
Speaker Distance (M1 to M6) 10'00''
ATT of all chan-
0.0 dB
Standing Wave
nels/filters
(M1 to M6)
SWch Wide Trim 0.0 dB
All channels/
0.0 dB
EQ Data (M1
bands
to M6)
EQ Wide Trim 0.0 dB
En
09
55