Network Settings From A Web Browser; Using The Sleep Timer; Dimming The Display; Switching The Hdmi Output - Pioneer Elite VSX-70 Operating Instructions Manual

09
ZONE 2 remote controls
Press the remote control's ZONE 2 to operate the corresponding zone.
The following table shows the possible ZONE 2 remote controls:
Button(s) What it does
Switches on/off power in the sub zone.
u
INPUT SELECT Use to select the input function in the sub zone.
Use to select the input function directly (this may not work for some functions) in the sub
Input function buttons
zone.
VOLUME +/–
Use to set the listening volume in the sub zone.
<a>
MUTE Mutes the sound or restores the sound if it has been muted (adjusting the volume also
<a>
restores the sound).
a ! The volume cannot be adjusted on the receiver if Volume Level at ZONE 2 Setup under ZONE Setup is set to –40 dB Fixed
or 0 dB Fixed.
Note
! The ZONE 3 button is not used with this unit.
HDZONE remote controls
Press the remote control's HDZONE to operate the corresponding zone.
The following table shows the possible HDZONE remote controls:
Button(s) What it does
Switches on/off power in the HDZONE.
u
INPUT SELECT Use to select the input function in the HDZONE.
Use to select the input function directly (this may not work for some functions) in the
Input function buttons
HDZONE.
Note
! The VOLUME +/– and MUTE buttons cannot be operated for HDZONE.

Network settings from a web browser

Network settings and Pandora account settings can be made using the browser on a computer connected to the
same LAN as the receiver.
1 Press u STANDBY/ON to switch on the receiver.
2 Turn on the computer's power and launch the Internet browser.
3 Input the receiver's IP address into the browser's address input field.
For example, if the receiver's address is 192.168.1.2, input "http://192.168.1.2/". Check the receiver's IP address at
Checking the Network Information on page 87.
When connected with the receiver, the Web Control screen appears in the browser.
4 When the Web Control screen appears, select the item you want to set.

Using the sleep timer

The sleep timer switches the receiver into standby after a specified amount of time so you can fall asleep without
worrying about the receiver being left on all night. Use the remote control to set the sleep timer.
% Press to the receiver operation mode, then press SLEEP repeatedly to set the sleep
time.
! You can check the remaining sleep time at any time by pressing SLEEP once. Pressing repeatedly will cycle
through the sleep options again.
! The sleep timer is valid for all zones. If any zone is on, the sleep timer continues functioning.

Dimming the display

You can choose between four brightness levels for the front panel display. Note that when selecting sources, the
display automatically brightens for a few seconds.
% Press to the receiver operation mode, then press DIMMER repeatedly to change the
brightness of the front panel display.
! You can also choose to turn the display off. In this case, the FL OFF indicator lights.

Switching the HDMI output

Set which terminal to use when outputting video and audio signals from the HDMI output terminals.
The HDMI OUT 1 terminal is compatible with the Control with HDMI function.
1 Press to the receiver operation mode, then press HDMI OUT.
Use k/l to select the setting.
2
Please wait a while when Please wait ... is displayed.
The output switches among OUT 1+2, OUT 1, OUT 2 and OFF each time the button is pressed.
! The synchronized amp mode is canceled when the HDMI output is switched. If you wish to use the synchro-
nized amp mode, switch to OUT 1, then select the synchronized amp mode on the TV using the TV's remote
control.
! When MAIN/HDZONE is set to HDZONE, it is not possible to switch to OUT 2
! Only signals input in HDMI format can be played with the HDMI OUT 2 terminal.

Checking your system settings

Use the status display screen to check your current settings for features such as surround back channel process-
ing and your current MCACC preset.
1 Press to the receiver operation mode, then press STATUS.
Use i/j to check the system setting.
2
The information on the main unit display switches as shown below each time one of the buttons is pressed.
Audio format f Sampling frequency f MCACC memory f Auto phase control plus correction value f
Input source to be played in ZONE 2 f Input source to be played in the HDZONE f HDMI output setting f
Subzone to which the HDZONE is output
! For some settings, some items are not displayed.
3 When you're finished, press STATUS again to switch off the display.
68
Using other functions
30 min 60 min
Off 90 min
(page 89).