Using The Sleep Timer; Dimming The Display; Switching The Hdmi Output; Checking Your System Settings - Pioneer VSX-LX52 Operating Instructions Manual

08 Using other functions

Using the sleep timer

The sleep timer switches the receiver into standby after a
specified amount of time so you can fall asleep without
worrying about the receiver being left on all night. Use
the remote control to set the sleep timer.
1
SIGNAL SEL MCACC
4
SBch A.ATT
7
D.ACCESS CH LEVEL
• Press RECEIVER
the sleep time.
• You can check the remaining sleep time at any time
by pressing SLEEP once. Pressing repeatedly will
cycle through the sleep options again.

Dimming the display

You can choose between four brightness levels for the
front panel display. Note that when selecting sources, the
display automatically brightens for a few seconds.
1
SIGNAL SEL MCACC
4
SBch A.ATT
7
D.ACCESS CH LEVEL
• Press RECEIVER
change the brightness of the front panel display.
Note
1 • You can also switch off the sleep timer simply by switching off the receiver.
• The sleep timer is valid for all zones. If any zone is on, the sleep timer continues functioning.
2 • Synchronized amp mode on page 60 is canceled when the HDMI output is switched. If you wish to use the synchronized amp mode, switch
to HDMI OUT 1, then select the synchronized amp mode on the flat screen TV using the flat screen TV's remote control.
• When the power is turned off then back on after switching the HDMI output, the input is set to a setting between HDMI1 and HDMI3, or BD.
3 If the Pure Direct mode is switched on, some settings above will show OFF, even though they are on.
66
En
HDMI OUT
CH
AUDIO INFO
2 3
DISP
SLEEP
RECEIVER
TV CTRL
5 6
REMOTE
DIMMER
SETUP
8 9
CLASS
ZONE 2 ZONE 3
MAIN
0
ENTER
, then press SLEEP repeatedly to set
30 min 60 min
Off 90 min
1
HDMI OUT AUDIO INFO CH
2 3
DISP
SLEEP RECEIVER
TV CTRL
5 6
REMOTE
DIMMER
SETUP
8 9
CLASS ZONE 2 ZONE 3
MAIN
0
ENTER
, then press DIMMER repeatedly to

Switching the HDMI output

Set which terminal to use when outputting video and
audio signals from the HDMI output terminals (HDMI
OUT ALL, HDMI OUT 1 or HDMI OUT 2).
The HDMI OUT1 terminal is compatible with the KURO
LINK function.
HDMI OUT
1 2 3
SIGNAL SEL MCACC SLEEP
4 5 6
SBch A.ATT DIMMER
7 8 9
D.ACCESS CH LEVEL CLASS
0
ENTER
RECEIVER
• Press , then press HDMI OUT.
Please wait a while when Please wait ... is displayed.
The output switches among HDMI OUT ALL, HDMI OUT 1
and HDMI OUT 2 each time the button is pressed.

Checking your system settings

Use the status display screen to check your current
settings for features such as surround back channel
processing and your current MCACC preset.
THX PHASE CTRL
TV/DTV MPX
AUDIO INFO
DISP
TV CTRL
REMOTE
1 Press RECEIVER , then press STATUS to check the
system settings.
These appear on the front panel display.
The front panel display shows each of the following
settings for three seconds each:
Input Source
Sampling Frequency
Surround Back channel Processing
MCACC preset
ZONE 2 input
ZONE 3 input
KURO LINK
HDMI OUT
2 When you're finished, press STATUS again to
switch off the display.
AUDIO INFO CH
DISP
RECEIVER
TV CTRL
REMOTE
SETUP
ZONE 2 ZONE 3
MAIN
2
STATUS
PQLS
CH
RECEIVER
3
↓
↓
↓
↓
↓
↓
↓