Panasonic PT-DW10000U Operating Instructions Manual page 68

Option1 settings (continued)
■
If "3COLORS" or "7COLORS"
was selected in step 2.
3. Press ENTER.
• The "COLOR MATCHING: 3COLORS" or
"COLOR MATCHING: 7COLORS" screen will
be displayed.
COLOR MATCHING:3COLORS COLOR MATCHING:3COLORS
R R
G G
B B
AUTO TESTPATTERN AUTO TESTPATTERN
MENU SELECT MENU SELECT
SUB MENU SUB MENU
ENTER ENTER
4. Press ▲▼ to select "R", "G" and
"B".
3COLORS:R 3COLORS:R
R R
G G
B B
MENU SELECT MENU SELECT
ADJUST ADJUST
5. Press ENTER.
6. Press ◄► to adjust the values.
• These values can be adjusted from 0 to 2048.
Note
• The effects of correcting the adjustment color:
When tuning the correction color that is the same
as the adjustment color: the brightness of the
adjustment color changes.
When tuning the correction color RED: RED is
added to or reduced from the adjustment color.
When tuning the correction color GREEN: GREEN
is added to or reduced from the adjustment color.
When tuning the correction color BLUE: BLUE is
added to or reduced from the adjustment color.
• This adjustment should be carried out by a person
who is familiar with the projector or by a service
person because a high level of skill is required to
make successful adjustment.
• Pressing DEFAULT will restore the factory defaults
for all items.
• When any setting other than "OFF" has been
selected for color matching, the "COLOR TEMP."
setting is fixed at "USER1".
68
– ENGLISH
ON ON
2048 2048
0 0
0 0
Adjusting the color matching
using a colorimeter
The "R (Red)", "G (Green)", "B (Blue)", "Cy (Cyan)",
"Mg (Magenta)", "Ye (Yellow)" and "Wh (White)"
colors can be changed to the desired hues using
a colorimeter which is capable of measuring the
chromaticity coordinates and luminance.
■
Inputting the current luminance
and chromaticity coordinates
1. Press ▲▼ to select "COLOR
MATCHING".
OPTION1 OPTION1
COLOR MATCHING COLOR MATCHING
LARGE SCREEN CORRECTION LARGE SCREEN CORRECTION
AUTO SIGNAL AUTO SIGNAL
AUTO SETUP AUTO SETUP
BACK COLOR BACK COLOR
DVI EDID DVI EDID
AUX DVI EDID AUX DVI EDID
P IN P P IN P
FUNC1 FUNC1
OSD POSITION OSD POSITION
OSD MEMORY OSD MEMORY
MENU SELECT MENU SELECT
CHANGE CHANGE
2. Press ◄► to select "MEASURE".
3. Press ENTER.
• The "MEASURE MODE" screen will be
displayed.
MEASURE MODE MEASURE MODE
MODE MODE
MEASURED DATA MEASURED DATA
TARGET DATA TARGET DATA
AUTO TESTPATTERN AUTO TESTPATTERN
MENU SELECT MENU SELECT
SUB MENU SUB MENU
ENTER ENTER
4. Press ▲▼ to select "MEASURED
DATA".
5. Press ENTER.
• The "MEASURED DATA" screen will be displayed.
MEASURED DATA MEASURED DATA
Y Y
Bk Bk
x x
y y
Y Y
R R
x x
y y
G G Y Y
x x
y y
B B Y Y
x x
y y
MENU SELECT MENU SELECT
ADJUST ADJUST
OFF OFF
OFF OFF
OFF OFF
BLUE BLUE
EDID2(PC) EDID2(PC)
EDID2(PC) EDID2(PC)
OFF OFF
P IN P P IN P
2 2
ON ON
709MODE 709MODE
ON ON
1/2 1/2
2 2
0.350 0.350
0.360 0.360
300 300
0.670 0.670
0.330 0.330
2500 2500
0.350 0.350
.0630 .0630
200 200
0.150 0.150
0.050 0.050