Ganz ZC-DN4312 NHA Operation Manual

MINI DOME COLOR CAMERA
ZC-DN4312 NHA/ZC-DN4312 PHA
Operation Manual
Camera adjustments
Camera adjustments for the ZC-DN4312NHA/PHA
DIP switch settings
The row of DIP switches allow the following settings to be made:
TDN mode
If this switch is set to "ON", the camera automatically captures the image
in color when the subject is bright and in B/W when the subject is dark.
Auto White Balance
AWB: The camera operates in the normal Auto White Balance range
2700K~11000K
AWB EX: The camera operates in the extended Auto White Balance
range 2000K~18000K
SYNC
In LL mode, the V-Phase may be adjusted to compensate for connected
supply phase differences.
Only applicable for 24 VAC supply - otherwise the camera operates with
INTernal sync.
Flickerless mode
If this switch is set to "ON", the camera reduces flicker in the image
under fluorescent lighting.
Black Light Compensation
If this switch is set to "ON", the camera response to strong unwanted
lighting effects behind the required subject is improved.
AGC mode
Setting to "AGC" will automatically increases the sensitivity even if the
brightness of the subject is insufficient. Selecting "NORMAL" will remove
noise from the image, but it will also limit the camera's sensitivity.
SHARP
Setting this switch to "ON" automatically creates subject sharpness.
Day and Night
The D&N mode can be activated if TDN is set to "ON". If set to "HI", the
time of automatically switching to Day or Night mode will be extended.
Focus & field of view adjustment
Twist the levers on the side of the vari-focal camera to adjust the focus
and field of view settings.
TIP: If necessary, perform the final focus through the dome cover,
holding it to the lens reversed to confirm the final results.
Vertical phase adjustment
Use this adjustment when using an AC supply to align the camera
phase with that of the supply.
DC-IRIS adjustment
This is factory set and should not normally require adjustment except to
compensate for excessive image blooming.
A.: Focus adjustment lever
B.:
View angle adjustment lever
C.: DIP switches
D.: DC-IRIS adjustment
E.: V-PHASE adjustment
ZC-DN4312NHA/PHA camera specifications
Type / Format ZC-DN4312NHA
NTSC 2:1 Interlace
Scanning Element
H:15734Hz, V:59.9Hz
Image Picture Element
Resolution (TV lines)
Minimum illumination
E p x o u s e r C o n r t l o
i l F k c r e e l s s
B L C
Day/Night
W h e t i B a a l n e c
Auto White Balance
Range
S y c n S s y e t m
Line Lock
(Phase Adj. Range)
Line Lock
(Frequency Range)
Video Output
S/N Ratio
W h e t i C p i l
Gamma Comp e n a s o i t n
Operation Temperature -10°C ~ +50°C (-30°C ~ +50°C with Heater)
Storage Temperature -20°C ~ +60°C (-35°C ~ +50°C with Heater)
Power Range
Power Consump n o i t
External Dimension
W e g i t h
Lens Specifications
F o c l a L e n g h t
- F N . o
r I s i R a n g e
M i n i m u m O b e j t c D s i a t n c e
Angle Of View Diagonal
H r o z i
V r e c i t
L e n s T p y e
ZC-DN4312PHA
PAL 2:1 Interlace
H:15625Hz, V:50Hz
1/3" Interline CCD sensor
540 TVL (normal)
0.08 lx @ F1.4
D C A u o t R I S I L e s n
M E S 1 1 / 0 s 0 c e 1 ( 1 / 2 ) 0
C e n r t l a A e r a f r o D C A u o t R I S I L
Burst ON/OFF & IR cut filter IN/OUT
A u o t W h e t i B a a l n e c
2700°K~11000°K (normal)
2000°K~18000°K (EX.)
n I e t n r a / l L n i e L o k c
0°~270°K
60Hz ± 1Hz 50Hz ± 1Hz
1.0 Vpp 75 Ohm BNC unbalance
50dB
1 2 0 R I E
0 4 . 5
DC 10.6V ~ 30V & AC 24V +/- 20%
4.2W
120(φ)mm x 100(H)mm
3 0 0 g
3.3~12 mm
F1.4
F1.4~F360
0 5 . m
125.7°~29.9°
o t n l a 89.8°~23.9°
l a 63.6°~17.9°
Aspherical
e s n