Advertisement
Quick Links
ASSEMBLY AND INSTALLATION
T0244 / T0245
WARNING:
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. Read and save these instructions.
Important to Know
1. Read all instructions carefully before installation and
operation.
2. If you are not familiar with state and local electrical
codes, it is recommended that you consult with a
qualified electrician.
3. Before installation, shut off power at the main fuse or
circuit breaker box. Be aware that simply turning off
the wall switch is not sufficient to prevent an electrical
shock.
4. This fixture requires a 120 VAC, 60 Hz power source.
Maximum wattage light bulb is 60W.
5. Do not attempt to take the lantern apart; there are
no serviceable parts inside.
6. To avoid sensor damage by lightning or electrical
surge, make sure the grounding wire is securely
connected.
7. For general safety and to avoid any possible damage
to the sensor, be sure the power is switched "off"
before replacing the bulb.
Maximum Wattage: 60W
Work Temperature: -4
Rubber Pad
Ball Nut
Lens
Metal Frame
Max.60W
standard base bulb
(Bulb not included)
INSTRUCTIONS
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
0
0
F ~ 104
F
Glass Panel
Features
1.Energy saving fixture.
2.Use the dim-to-bright illumination option where
you want some minimum illumination through out
the night, such as at your front entrance or garage
door. Use the dark-to-bright illumination option
where you do not need minimum brightness, such
as the backyard or back porch.
3.When in manual override mode, use wall switch
to keep the light on till dawn.
Hardware Package (included)
Mounting Plate
X1
Mounting Screw
X2
Headless Screw
Fixture Wire
Wire Nut
Back Plate
Glass Panel
Clip
Metal Frame
Page 1 / 4
Headless Screw
Wire Nut
X2
X3
Lock Nut (D)
Ball Nut
Green Grounding
X4
X2
Mounting plate
Green Grounding Screw
House Grounding Wire
Fixture Grounding Wire
"L"Clip
Fig.2
160830
Rubber Pad
X2
Screw
Lock Nut
Outlet Box
Fig.1
Advertisement
Related Manuals for Vaxcel T0244
Summary of Contents for Vaxcel T0244
- Page 1 ASSEMBLY AND INSTALLATION INSTRUCTIONS T0244 / T0245 WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. Read and save these instructions.
- Page 2 Installation Steps 1. Shut off power at the circuit breaker of where the fixture is to be installed. 2. Thread two headless screws through the mounting plate, then secure them with four lock nuts(two on each side of the mounting plate). Adjust the length of the headless screws if necessary.
- Page 3 5.Manual Override MODE (nighttime operation only; on at dusk,off at dawn) ● In 3, 6 or 0 mode, to shift to manual override mode, turn off the wall switch in 3 seconds and then turn it on again, the light will turn to high-level brightness at dusk, and turn off automatically at dawn. To return to the previous settings, turn off the wall switch in 3 seconds and then turn it on again.
- Page 4 Spare Parts List: Assembly Kit 5533MM(1 SET) Headless Screw Wire Nut Rubber Pad Mounting Plate Glass Panel 9837CS for T0244 3838CS for T0245 Mounting Screw Lock Nut (D) Ball Nut Green Grounding Screw (C) 5-YEAR LIMITED WARRANTY: All products are warranted to be free of defects in material and workmanship for five (5) years from date of purchase.