Advertisement
Quick Links
ASSEMBLY AND INSTALLATION
T0252 / T0253 / T0260 / T0261 / T0262 / T0263
WARNING:
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. Read and save these instructions.
Important to Know
1. Read all instructions carefully before installation and
operation.
2. If you are not familiar with state and local electrical codes,
it is recommended that you consult with a qualified
electrician.
3. Before installation, shut off power at the main fuse or
circuit breaker box. Be aware that simply turning off the
wall switch is not sufficient to prevent an electrical shock.
4. This fixture requires a 120 VAC, 60 Hz power source.
5. Do not attempt to take the lantern apart; there are no
serviceable parts inside.
6. To avoid sensor damage by lightning or electrical surge,
make sure the grounding wire is securely connected.
7. For general safety and to avoid any possible damage to
the sensor, be sure the power is switched "off" before
replacing the bulb.
8. Compatible with LED dimmable bulb.
Maximum Wattage: 60W Incandescent Bulb or 20W LED
dimmable bulb.
Work Temperature: -4°F~104°F
Green Grounding Screw (C)
Cross Bar (A)
Lock Nut (F)
Outlet Box
Mounting Screw (B)
House Grounding Wire
Fixture Grounding Wire
INSTRUCTIONS
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
Headless Screw (D)
Fixture Wire
Wire Nut (E)
Rubber Pad (H)
Ball Nut (G)
Page 1/4
Features
1. Energy saving fixture.
2. Use the dim-to-bright illumination option where
you want some minimum illumination through out
the night, such as at your front entrance or garage
door. Use the dark-to-bright illumination option
where you do not need minimum brightness, such
as the backyard or back porch.
3. When in manual override mode, use wall switch
to keep the light ON till dawn.
Hardware Package (included):
Mounting Screw (B)
Cross Bar (A)
Lock Nut (F)
Wire Nut (E)
Back plate
Small Ball nut
Rubber pad
Fixture
FOR T0252/T0253/T0260: Type A15,Type B
FOR T0261/T0262/T0263: Type A
Max. 60W: Incandescent/Halogen Bulb or
Max.20W Dimmable LED Bulb
(not include)
Glass Shade
Metal frame
Green Grounding
Screw (C)
Rubber Pad (H)
Ball Nut (G)
161028
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Vaxcel T0252
Summary of Contents for Vaxcel T0252
- Page 1 ASSEMBLY AND INSTALLATION INSTRUCTIONS T0252 / T0253 / T0260 / T0261 / T0262 / T0263 WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
- Page 2 Installation steps Turn off the power at fuse or circuit box. 1.Thread two headless screws through the cross bar, then screw them with four lock nuts (two on each side of the cross bar). Adjust the length of the headless screw if necessary. Note: Make sure that the headless screws are lined up horizontally, to ensure that the fixture will be level.
- Page 3 FIG.2 FIG.1 On the back of the sensor Low Level Sens Time Turn wall switch OFF-ON in 3 Seconds Manual AUTO Mode Override Mode Turn wall switch OFF-ON Test 3H 6H in 3 Seconds again CUSTOMIZATION OPTIONS: Shut-off Delay The Shut-off delay is the length of time the light will stay at high-level brightness after motion has ceased to be detected.
- Page 4 Vaxcel reserves the right to repair, replace or issue a credit for any properly installed product, provided it is returned per RMA instruction. This warranty is limited to the cost of the product only and does not extend to transportation, installation or replacement costs.
Need help?
Do you have a question about the T0252 and is the answer not in the manual?
Questions and answers