Table of Contents
Advertisement
INSTALLATION INSTRUCTIONS
THINGS YOU NEED TO KNOW
WARNINGS:
l
This appliance must be installed by a qualified
electrician/competent
impaired if installation is not carried out in
accordance with these instructions.
l
This appliance must be earthed.
l
Do not remove the screws from the earth tab
extending from the oven mains terminal block (Fig.
6).
l
Before connecting the appliance make sure that the
voltage of your electricity supply is the same as that
indicated on the rating plate. This is situated on the
lower front frame of the appliance upon opening the
main cavity door. Alternatively the rating plate may
also be found on the back or top of some models
(where applicable).
l
Do not alter the electrical circuitry of this appliance.
THINGS TO NOTE
l
This appliance is designed to be fitted in cabinets of
the recommended dimensions as shown (Fig. 2).
l
If your cabinet interior dimension is between
565-570mm the oven may still be fitted. However a
minor modification to the cabinet will be required to
reduce the aperture size to 560-565mm. To allow
the appliance to securely screwed in to the cabinet.
l
The
dimensions
circulation around the unit within the cabinet,
ensuring compliance with BS EN60-335.
l
Enquiries regarding the installation of the cooker
point, if required, should be made to your Regional
Electricity Company to ensure compliance with their
regulations.
l
The cooker socket switch should be outside the
cabinet but within 2m of the appliance to make it
accessible to switch off the appliance in case of an
emergency.
l
To protect the hands, wear gloves when lifting the
oven into its housing.
NOTE: HOUSE CIRCUIT
Earth leakage and continuity tests must be carried out
before the appliance is connected to the mains supply
and re-checked after fitting.
GETTING THINGS READY
CHOICE OF ELECTRICAL CONNECTION
l
There are three possible ways to connect your
appliance. In each case the appliance should be
operated using at least 6mm² twin core and earth
PVC insulated multicore cable. Please choose
from the most appropriate after reading the
different methods:-
person.
Safety
may
given
provide
adequate
a) By connecting the appliance to a cooker point
(having a double pole isolating switch with at least
3mm contact separation in all poles and neutral)
and protected with a fuse or miniature circuit
be
breaker at your mains fuse box.
Subject to Regional Electricity Companies
regulations if you wish to connect the oven
and hob to the power supply you may use
one of the following two methods:-
b) By connecting the appliance together with a hob
directly to a cooker point(s). Having a double pole
isolating
switch
separation in all poles and neutral.
c) If you wish to connect an oven and a hob to a
cooker point you can by connecting the oven and
hob separately to the cooker point. Oven and hob
units should be separately connected to a cooker
point. See Fig. 1.
air
Fig. 1
NOTE: It is good practice to:
l
Fit an Earth Leakage Circuit Breaker to your house
wiring.
l
Wire your appliance to the latest IEE regulations.
PREPARING CABINET FOR FITTING OF OVEN
l
Make sure the cabinet is the correct size for the
appliance to be fitted (Ref. Fig. 2).
l
If the size is between 565-570mm, then the cabinet
should be modified so that at the screw fixing points
the recommended dimension of at least 560-565mm
is maintained. The modification should ideally be
localised to ensure
oven is securely fixed into position.
l
The cabinet must be stable and level by firmly
securing it to the wall or floor. If necessary, make
arrangements to ensure the shelf upon which the
oven will rest is level.
l
When the appliance is installed ensure a minimum
gap of 2mm is maintained between the trim on the
bottom
edge
corresponding door / panel underneath.
7
with
at
least
3mm
that after screw fitment the
of
the
appliance
contact
and
any
Advertisement
Table of Contents
