Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Atag VA61313MT
Summary of Contents for Atag VA61313MT
- Page 1 User Manual Dishwasher VA61313MT...
-
Page 2: Table Of Contents
CONTENTS Safety information Before first use Safety instructions Daily use Product description Hints and tips Control panel Care and cleaning Programmes Troubleshooting Settings Technical information Options Subject to change without notice. SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. -
Page 3: Safety Instructions
by clients in hotels, motels, bed & breakfast and other – residential type environments. Do not change the specification of this appliance. • The operating water pressure (minimum and maximum) • must be between 0.5 (0.05) / 8 (0.8) bar (MPa) Obey the maximum number of 13 place settings. - Page 4 • Do not use multi-plug adapters and • If the water inlet hose is damaged, extension cables. immediately close the water tap and • Make sure not to cause damage to the disconnect the mains plug from the mains plug and to the mains cable. mains socket.
-
Page 5: Product Description
PRODUCT DESCRIPTION Upper spray arm Rinse aid dispenser Lower spray arm Detergent dispenser Filters Cutlery basket Rating plate Lower basket Salt container Upper basket Air vent Beam-on-Floor The Beam-on-Floor is off when the appliance is deactivated. The Beam-on-Floor is a light that is displayed on the floor below the appliance When AirDry is activated during door. -
Page 6: Control Panel
CONTROL PANEL On/off button Programme buttons Display Indicators Delay button Indicators Indicator Description Extra Dry indicator. Rinse aid indicator. It is always off while the programme operates. Salt indicator. It is always off while the programme operates. PROGRAMMES Programme Degree of soil Programme phases Options Type of load... -
Page 7: Settings
Programme Degree of soil Programme phases Options Type of load • • Prewash 1) With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil. (This is the standard programme for test institutes). 2) The appliance senses the degree of soil and the quantity of items in the baskets . - Page 8 To enter user mode, press and hold How to set the programme simultaneously until selection mode the indicators The appliance is in programme selection flash and the display is blank. mode when the programme indicator The water softener flashes and the display shows the programme duration.
- Page 9 2. Press to change the setting. How to set the water softener level = the rinse aid empty notification is deactivated. Make sure the appliance is in user mode. 3. Press on/off to confirm the setting. 1. Press Acoustic signals •...
-
Page 10: Options
How to deactivate AirDry During the drying phase, the door opens automatically and Make sure the appliance is in user mode. remains ajar. 1. Press CAUTION! Do not try to close • The indicators the appliance door within 2 minutes after automatic are off. -
Page 11: Before First Use
BEFORE FIRST USE 1. Make sure that the current level of 4. Carefully shake the funnel by its the water softener agrees with the handle to get the last granules inside. hardness of the water supply. If not, 5. Remove the salt around the opening of adjust the level of the water the salt container. -
Page 12: Daily Use
1. Press the release button (D) to open the lid (C). 2. Pour the rinse aid in the dispenser (A) until the liquid reaches the fill level 'max'. 3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam. - Page 13 • 5 minutes after the completion of the If the door is opened for more programme. than 30 seconds during the • After 5 minutes if the programme has drying phase, the running not started. programme ends. It does not happen if the door is opened by Starting a programme AirDry function.
-
Page 14: Hints And Tips
HINTS AND TIPS General we recommend that you use the tablets with long programmes. The following hints will ensure optimal • Do not use more than the correct cleaning and drying results in daily use quantity of detergent. Refer to the and also help to protect the environment. -
Page 15: Care And Cleaning
• Put light items in the upper basket. • The programme is applicable for the Make sure that the items do not move. type of load and for the degree of soil. • Make sure that the spray arm can •... - Page 16 CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object.
-
Page 17: Troubleshooting
TROUBLESHOOTING If the appliance does not start or it stops With some problems, the display during operation, first check if you can shows an alarm code. solve the problem by yourself with the The majority of problems that can help of the information in the table or occur can be solved without the need contact an Authorised Service Centre. - Page 18 Problem and alarm code Possible cause and solution The remaining time in the • This is not a defect. The appliance is working correctly. display increases and skips nearly to the end of program time. Small leak from the appli‐ •...
- Page 19 Problem Possible cause and solution Poor drying results. • Tableware has been left for too long inside a closed ap‐ pliance. • There is no rinse aid or the dosage of rinse aid is not enough. Set the rinse aid dispenser to a higher level. •...
-
Page 20: Technical Information
Problem Possible cause and solution Limescale deposits on the ta‐ • The level of salt is low, check the refill indicator. bleware, on the tub and on the • The cap of the salt container is loose. inside of the door. •... - Page 24 When contacting the service department, have the complete type number to hand. You will find the addresses and phone numbers of the service organisation on the guarantee card. 156919280-A-232017...
Need help?
Do you have a question about the VA61313MT and is the answer not in the manual?
Questions and answers