Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Zebex Z-5652 Plus
Summary of Contents for Zebex Z-5652 Plus
- Page 1 Z-5652 plus Series 2D Image Hands-Free Scanner...
- Page 3 ’ ANUAL Revision History Changes to the original manual are listed below: Version Date Description of Version 10/02/2017 Initial release 2D Image Scan Module...
- Page 4 ’ ANUAL Important Notice No warranty of any kind is made in regard to this material, including, but not limited to, implied warranties of merchantability or fitness for a particular purpose. We are not liable for any errors contained herein or incidental or consequential damages in connection with furnishing, performance or use of this material.
-
Page 5: Table Of Contents
’ ANUAL Table of Contents Introduction .........................1 Unpacking........................2 Outline .........................3 Installing the Device .....................4 Using Mounting Screw ..................4 Connection........................5 Power Connection....................5 Scanner Operation .......................7 Setting Up the Scanner....................8 Scan Test........................8 Programming the Scanner ...................9 Scan Mode of Scanner ....................10 Auto-Scan Mode....................10 Manual Scan Mode ....................10 Sleep Mode ......................11 Beeper Indication.......................12... -
Page 7: Introduction
’ ANUAL Introduction Lighting speed without compromising performance, the scanner features a powerful 2D engine that easily decodes most 1D and 2D barcodes with intuitive aiming accuracy. It also excels at reading barcodes on smart phone screens and barcodes that are poorly printed. -
Page 8: Unpacking
’ ANUAL Unpacking The hands-free scanner package contains: 2D image scan module with selected interface cable Power adapter (only for specific RS-232 cables as optional accessory) Quick Guide Please leave this user’s manual within easy access for persons using the scanner. ... -
Page 9: Outline
’ ANUAL Outline # Description Function 1 Trigger Button Push to scan 2 Speaker Exit For beep tone indication 3 LED Indicator For status indication 4 Scan Window Read barcodes 5 Tripod Socket For mounting the device on camera tripod 6 Mounting holes For mounting the device 2D Image Scan Module... -
Page 10: Installing The Device
’ ANUAL Installing the Device Using Mounting Screw The device is reserved with 3 mounting holes for permanent fixture if required. Refer to the figure below for detailed information. Unit: mm(inch) Mounting screw holes 2D Image Scan Module... -
Page 11: Connection
’ ANUAL Connection Power Connection The scanner turns on when power is supplied, and turns off when power is removed. There is no on/off switch on the scanner itself. The scanner requires a minimum of 2W at 5VDC power. The interface cable that comes with the scanner supports both direct power (where the scanner takes power from the host machine) and external power (that’s what the supplied power adapter is for). - Page 12 ’ ANUAL Follow the steps below when you need an external power connection to the scanner: Connect the interface cable to the bottom of the scanner. Connect the other end of the interface cable to the host (refer to your host manual to locate the correct port).
-
Page 13: Scanner Operation
’ ANUAL Scanner Operation Please follow the procedure below to verify scanning operation. If necessary, plug the power adapter into the jack on the interface cable. Plug the AC end of the power adapter into an AC outlet, or plug the other end of cable into host if power adapter is not needed. -
Page 14: Setting Up The Scanner
’ ANUAL Setting Up the Scanner In certain cases no setup is required. The scanner is either pre-programmed to suit the situation, or it automatically detects and is ready to go. In other cases the scanner must be informed about what kind of system it is connected to. This can be done in a few moments using the programming barcodes in the Programming Guide. -
Page 15: Programming The Scanner
’ ANUAL Programming the Scanner When the scanner is powered on (blue LED lights), find the <Set> barcode in the Programming Guide and present this barcode to the scanner. When the scanner gives two beeps, it means the scanner is in programming mode. Decide which parameters are required and find their barcodes in the Programming Guide. -
Page 16: Scan Mode Of Scanner
’ ANUAL Scan Mode of Scanner Auto-Scan Mode This scanner support auto-scan mode, the scan LED light stays active and continues to decode until a same barcode is scanned. If no barcode is present in the scanning field for 10 seconds, the scanner goes to standby with scan LED light continues to flash. Manual Scan Mode The scanner can also be used as a handheld scanner by simply pressing the button. -
Page 17: Sleep Mode
’ ANUAL Sleep Mode After the scanner has been inactive for a period of time, the scanner would enter the sleep mode. After 5 minutes inaction, the scanner would enter the sleep mode from continue scan mode. The time period of continue scan mode is programmable. To wake up the scanner, present an object close to the scan window, or press the trigger button. -
Page 18: Beeper Indication
’ ANUAL Beeper Indication Beeps Indication 3 beeps in a series from low to high pitch Power up 1 short beep A barcode has been successfully decoded 2 short beeps The scanner has entered program mode 1 long beep A setting has been programmed 3 beeps in a series from low to high pitch The scanner has exited program mode 3 short beeps... -
Page 19: Usb Virtual Com
’ ANUAL USB Virtual COM If you use virtual COM port emulation, follow the steps below to start using the scanner. Execute the driver (VCOM-Driver-Installation.exe). Connect the scanner USB cable to the host computer. Set the interface to USB Virtual COM Port. Enable USB virtual COM 2D Image Scan Module... -
Page 20: Trouble Shooting
’ ANUAL On the computer, check Device Manager to see if the computer successfully detects the scanner as “Barcode Scanner USB-COM device.” (The COM port number would vary depending on different hardware environment). Trouble Shooting This section contains information about how to solve problems that you may encounter when operating the scanner. -
Page 21: Maintaining The Scanner
’ ANUAL Maintaining the Scanner Cleaning the Scan Window The scanner is designed for long-term trouble-free operation and rarely requires any maintenance. Only an occasional cleaning of the scanner window is necessary in order to remove dirt and fingerprints. Wipe the scan window with a soft lint-free cloth and a non-abrasive cleaner to avoid scratching and damaging the scan window. -
Page 22: Dimension
’ ANUAL Dimension Unit: mm 2D Image Scan Module... - Page 23 ’ ANUAL Specification Sensor Resolution 752H × 480V pixels Light Source 4* 617nm LED (Red) Image Field of View (Scan Zone) 44.4°H x 29.1°V Roll/ Pitch/ Yaw 360°/ ± 65°/ ± 60° Scan Rate 60 fps Optical Print Contrast Ratio (Minimum) 30% Code 39 (5 mil): 65 - 115 mm UPC/EAN (13 mil): 40 - 250 mm Minimal Element Resolution...
-
Page 24: Connector And Pin Out
’ ANUAL Connector and Pin Out RS-232 interface (DTE Pinout) – Power adapter required if host can not provide sufficient power PIN-OUT CONFIGURATION PIN FUNCTION PIN FUNCTION N.C. N.C. +5V Input Inner of DC-Jack: +5V DC Outer of DC-Jack: GND USB /USB virtual COM / OPOS USB interface FUNCTION VBUS...