Motorola AP-0622 Installation Manual
  1. Manuals
  2. Brands
  3. Motorola Manuals
  4. Wireless Access Point
  5. AP-0622
  6. Installation manual
Motorola AP-0622 Installation Manual

Motorola AP-0622 Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

AP-0622 Access Point
INSTALLATION GUIDE

Advertisement

Table of Contents
loading

Related Manuals for Motorola AP-0622

Summary of Contents for Motorola AP-0622

  • Page 1 AP-0622 Access Point INSTALLATION GUIDE...
  • Page 2 AP-0622 Access Point MOTOROLA SOLUTIONS and the Stylized M Logo are registered in the US Patent & Trademark Office. © Motorola Solutions, Inc. 2011. All rights reserved.

  • Page 3: Table Of Contents

    1.3 Site Preparation ........5 1.4 AP-0622 Package Contents ....... 5 2.0 Hardware Installation .

  • Page 4: Introduction

    The AP-0622 access point provides multiple deployment options. The AP-0622 access point receives all power and transfers data through the same CAT-5 or better Ethernet cable. An 802.3af Ethernet switch or power supply (specifically rated for the AP-0622) is required (Part No.

  • Page 5: Warnings

    • Verify cable lengths are within the maximum allowable distances for optimal signal transmission. 1.4 AP-0622 Package Contents An AP-0622 access point is available in integrated antenna and external antenna models. Contents differ depending on the model ordered. 1.4.1 External Antenna Model Package Contents •...
  • Page 6 • Lock port for Kensington style Security Lock The AP-0622 access point has one RJ-45 connector supporting an 10/100/1000 Ethernet port and accepts 802.3af-compliant power from an external source. The illustration below is of an integrated antenna model AP-0622.

  • Page 7: Hardware Installation

    2.1 Installation Instructions The AP-0622 access point mounts either on a wall (with customer supplied M4 x 25 pan head screws and wall anchor - or equivalent) or on a suspended ceiling T-bar. If deploying an external antenna model AP622, access point mounting kit (Part No.

  • Page 8: Access Point Placement

    2.4 Integrated Antenna Model Wall Mount Instructions This mounting requires hanging the AP-0622 along its width or length using the two slots on the bottom of the unit. The AP22 can be mounted onto any plaster, wood, or cement wall surface using customer supplied screw hardware (M3.5 x 0.6 x 20 mm- or equivalent).
  • Page 9 Installation Guide 2.4.2 Wall Mount Procedure 1. Orient the case on the wall by its width or length. To ensure proper operation of an AP-0622 access point, ensure it is CAUTION mounted in the correct orientation as shown above.
  • Page 10 5. Attach an Ethernet cable from the access point to a controller with an 802.3af-compatible power source or use the PWRS-14000-148R power supply to supply power to the AP-0622 (once fully cabled). 6. Place the middle of each of the case’s mount slots over the screw heads.

  • Page 11: Integrated Antenna Model Suspended Ceiling T-Bar Mount

    Installation Guide 2.5 Integrated Antenna Model Suspended Ceiling T-Bar Mount Ceiling mount requires holding the AP-0622 access point up against a T-bar of a suspended ceiling grid and twisting the case onto the T-bar. 2.5.1 Suspended Ceiling T-Bar Mount Procedure 1.

  • Page 12: External Antenna Model Wall Mount Instructions

    A wall mount deployment requires hanging the AP-0622 access point along its width or length using the pair of slots on the bottom of the unit. The AP-0622 can be mounted on to any plaster, wood or cement wall surface using the provided wall anchors.
  • Page 13 Installation Guide 1. Attach the two provided mounting ears (using four ear mounting screws) to the two narrow ens of the AP-0622. Align the ears using the built in ear alignment pin on the access point housing. Torque the screws to 6 lb-in.
  • Page 14 An existing external antenna model AP300 (WSAP-5100-100) or external antenna model AP650 (AP-0650-660X0) access point, installed on a wall (plenum installation), can be placed by an AP-0622. Simply remove the existing legacy model access point form its mounting screws, leave the mounting hardware in place and install the new external antenna model AP-0622 directly on to the existing mounting hardware.

  • Page 15: External Antenna Model Suspended Ceiling T-Bar Mount

    2.7 External Antenna Model Suspended Ceiling T-Bar Mount Ceiling mount requires holding the AP-0622 access point up against a T-bar of a suspended ceiling grid and twisting the case onto the T-bar. If deploying an external antenna model AP-0622 on a ceiling T-Bar, access point mounting kit (Part No.
  • Page 16 5. Attach an Ethernet cable from the access point to a controller with an 802.3af compatible power source or use the PWRS-14000-148R power supply to supply power to the AP-0622 (once fully cabled). 6. Attach appropriate antennas to the connectors.

  • Page 17: External Antenna Suspended Ceiling Tile (Plenum) Mount

    6. Attach an Ethernet cable from the access point to a controller with an 802.3af compatible power source or use the PWRS-14000-148R power supply to supply power to the AP-0622 (once fully cabled). 7. Verify the access point is receiving power by observing the LEDs.

  • Page 18: Ap-0622 External Antenna Model Antenna Options

    2.9 AP-0622 External Antenna Model Antenna Options Motorola Solutions supports two antenna suites for AP-0622 External Antenna models. One antenna suite supporting the 2.4 GHz band and another antenna suite supporting the 5 GHz band. Select an antenna model best...
  • Page 19 ML-2452-PNA5-01R Panel Antenna ML-2452-PTA3M3-036 Omni Antenna ML-2452-APAG2A1-01 (Black) Dipole Antenna ML-2452-APAG2A1-02 (White) For up-to-date information on supported antennas and antenna specifications, please refer to the Motorola Solutions Enterprise Wireless LAN Antenna Specification Guide available on the Motorola Solutions Web site.

  • Page 20: Led Indicators

    AP-0622 Access Point 2.10 LED Indicators Both Integrated Antenna and External Antenna models have LED activity indicators on the front of the case. With the External Antenna models mounted above a ceiling, LEDs are at the center of an oval badge on the ceiling.
  • Page 21 Installation Guide Task 5 GHz Activity LED (Amber) 2.4 GHz Activity LED (Green) Unadopted Blinking at 5Hz Normal • If this radio band is enabled: • If this radio band is enabled: Operation Blink at 5 second interval Blink at 5 second interval •...

  • Page 22: Initial Access Point Configuration

    RFS7000 or NX9000 series controller. There are no required initial configuration settings beyond verifying power and LED functionality for an AP-0622 model access point. Once adopted, the access point is managed by its connected controller and can receive periodic firmware updates when Motorola Solutions releases updates with new controller functionality.

  • Page 23: Specifications

    Voltage 48V,0.25A (PoE connector) 4.2 AP-0622 Integrated Antenna Model Physical Characteristics An AP-0622 Integrated Antenna model Access Point has the following physical characteristics: Dimensions 9.38 inches x 7.5 inches x 1.38 inches 23.82 cm x 19.50 cm x 3.50 cm...

  • Page 24: Ap-0622 External Antenna Model Electrical Characteristics

    AP-0622 Access Point 4.3 AP-0622 External Antenna Model Electrical Characteristics An AP-0622 External Antenna model Access Point has the following electrical characteristics: Operating Current & 12VDC, 1A (accessory power connector) Voltage 48V,0.25A (PoE connector) 4.4 AP-0622 External Antenna Model Physical Characteristics...

  • Page 25: Radio Characteristics

    Installation Guide 4.5 Radio Characteristics The AP-0622 model Access Points have the following radio characteristics: Operating Channels All channels from 4920 MHz to 5825 MHz except channel 52 -64 Channels 1-13 (2412-2472 MHz) Channel 14 (2484 MHz) Japan only Actual operating frequencies depend on regulatory approval for the country of use.

  • Page 26: Regulatory Information

    Solutions, Inc. (collectively "Motorola"). This guide applies to Model Number AP-0622. All Motorola/Symbol devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required. Local language translations are available at the following website: http://supportcentral.motorola.com/...
  • Page 27 Installation Guide Industry Canada Statement: Caution: The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-Channel mobile satellite systems. High power radars are allocated as primary users (meaning they have priority) of 5250-5350 MHz and 5650-5850 MHz and these radars could cause interference and/or damage to LE-LAN devices.
  • Page 28 Power Supply Use ONLY a LISTED Motorola, Type no. PWRS-14000-148R (12VDC @ 4.16A), direct plug-in power supply, marked Class 2 (IEC60950-1, SELV). This device can be powered from a 802.3af compliant power source which is certified by the appropriate agencies.
  • Page 29 Installation Guide Radio Frequency Interference Requirements—FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
  • Page 30 Italy requires a user license for outside usage. Statement of Compliance Motorola hereby, declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A Declaration of Conformity may be obtained from http://www.motorola.com/doc.
  • Page 31 Installation Guide Taiwan 5.25-5.35 Korea 당해 무선설비는 운용 중 전파혼신 가능성이 있음 당해 무선설비 는전파혼 신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다 Turkish WEEE Statement of Compliance EEE Yönetmeli ine Uygundur...
  • Page 32 : http://www.motorola.com/recycling/weee. Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a Motorola al final de su ciclo de vida para que sean reciclados. Si desea más información sobre cómo devolver un producto, visite: http://www.motorola.com/recycling/weee.
  • Page 33 žinti gamin , rasite: http://www.motorola.com/recycling/weee. Latviešu: ES klientiem: visi produkti p c to kalpošanas m ža beig m ir j nog d atpaka Motorola otrreiz jai p rstr dei. Lai ieg tu inform ciju par produktu nog d šanu Motorola, l dzu, skatiet: http://www.motorola.com/recycling/weee.

  • Page 34: Part Numbers, Support, And Sales

    • Model number or product name • Software type and version number Motorola Solutions responds to calls by email or telephone within the time limits set forth in support agreements. If you purchased your Enterprise Mobility business product from a Motorola Solutions business partner, contact that business partner for support.

  • Page 35: Motorola Solutions, Inc. End-User License Agreement

    BIND THAT COMPANY, PERSON OR ENTITY. LICENSE GRANT. Subject to the terms of this Agreement, Motorola, Inc. and/or its subsidiaries ("Licensor") hereby grants Licensee a limited, personal, non-sublicensable, non-transferable, nonexclusive license to use the software that Licensee is about to download or install and the documentation that accompanies it (collectively, the "Software") for Licensee's personal use in connection with...
  • Page 36 FAR, 48 CFR 52.227-14 (JUNE 1987) or DFAR, 48 CFR 252.227-7013 (OCT 1988), as applicable. The "Manufacturer" for purposes of these regulations is Motorola, Inc., One Symbol Plaza, Holtsville, NY 11742. EXPORT RESTRICTIONS. Licensee shall comply with all export laws and restrictions and regulations of the Department of Commerce, the United States Department of Treasury Office of Foreign Assets Control ("OFAC"), or other United States or foreign agency or...
  • Page 37 Installation Guide Agreement shall be held by a court or other tribunal of competent jurisdiction to be illegal, invalid or unenforceable, such provisions shall be limited or eliminated to the minimum extent necessary so that this Agreement shall otherwise remain in full force and effect. No waiver or modification of this Agreement will be binding upon a party unless made in writing and signed by a duly authorized representative of such party and no failure or delay in enforcing any right will be deemed a waiver.

  • Page 38: Ap-0622 Access Point China Rohs Compliance

    塑料和聚合物部件 (Plastic and Polymeric Parts) 光学和光学组件 (Optics and Optical Components) 电池 (Batteries) O： 表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以 下。 X： 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量 要求。 对销售之日的所售产品，本表表示，公司供应链的电子信息产品可能包含这些物质。注意：在所售产品 中可能会也可能不会含有所有所列的部件。 This table was created to comply with China RoHS requirements for Motorola Solutions‘ AP-0622 Access Point.
  • Page 39 Installation Guide...
  • Page 40 Schaumburg, IL 60196-1078, U.S.A. http://www.motorolasolutions.com MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2011 Motorola Solutions, Inc. All Rights Reserved.

Table of Contents