Related Manuals for Triax C-HD207CG
Summary of Contents for Triax C-HD207CG
- Page 1 Triax C-HD207CG Digital Cable-TV Receiver Model Item no. Triax C-HD207CG 305207/305208 triax.com Version 01- 2011...
-
Page 2: Table Of Contents
Content Content Content ............................2 General instructions ........................3 Safety Instructions ......................... 4 Cleaning and care .......................... 4 Control elements, front and rear panel..................5 Connecting the receiver ......................... 6 Remote control ..........................7 Initial installation ..........................8 Operating the receiver ......................... 10 EPG –... -
Page 3: General Instructions
Recording ..........................26 Timeshift function ........................26 Playback ............................27 Choosing the audio channel for recordings ................27 Fast forward and rewind......................27 Operating the hard disk – setting and managing markers ............ 28 Using serial interface ........................29 Make a contribution to environmental protection ................ 29 Trouble-shooting .......................... -
Page 4: Safety Instructions
Safety Instructions Safety Instructions Before installing your digital receiver, all security and operating instructions should be read carefully. The User’s Manual should be retained for future reference. All operating and using instructions should be followed. Never allow children to operate this electrical device without supervisor. ENVIRONMENTAL CONDITIONS Protect the receiver against humidity, heat and cold. -
Page 5: Control Elements, Front And Rear Panel
Control elements, front and rear panel Control elements, front and rear panel 4-digit display shows channel number Display Receiver in standby mode. Channel number Receiver is ON rEC. Timer activated Smartcard reader Connector for mains adapter 12VDC TV-Scart port for connecting the TV HDMI-Output (digital Audio- and Videosignal) for connecting the TV USB-socket for external mass storage device (Option) RF Input Digital –... -
Page 6: Connecting The Receiver
Connecting the receiver Connecting the receiver RF (HF) connection Connect the RF Input Digital socket (6) of the receiver to your cablesignal wall socket. Connecting a television Use a scart cable to connect the TV socket (3) on the receiver to the corresponding scart socket on the television set. -
Page 7: Remote Control
Remote control Remote control... -
Page 8: Initial Installation
Initial installation Initial installation After reading the safety instructions (see chapter “safety instructions)” and finishing the actions explained in chapter “connecting the receiver” please use the supplied power cord for connecting the apparatus to the power supply. When running the receiver for the first time the “welcome menu”... - Page 9 Sort channels In the last step of the initial installation you are asked, if the channels which are found during the channel search, should be Welcome sorted automatically. Sort channels? Note: This function is only effective, if accordant channel list informations are sent by the broadcast-station. Use the buttons to select NO or YES and confirm with OK.
-
Page 10: Operating The Receiver
Operating the receiver Operating the receiver Switching receiver ON/OFF This receiver is equipped with a low power standby circuit. If this function is activated, the standby power consumption of the receiver is less than 1W. The function is switched ON or OFF in the menu SETTINGS/RECEIVER SETUP. Low-Power Standby ON –... - Page 11 Operating the receiver Selecting a channel Using the directional up/down keys To change the channels stepwise press the buttons . In order to switch the channels quicker hold these buttons pressed longer. Using the numeric keys (direct input) One or more digit channel numbers can be input by using the numeric buttons 0…9 and pressing OK.
-
Page 12: Epg - Electronic Programme Guide
EPG – Electronic Programme Guide EPG – Electronic Programme Guide Almost all TV and radio broadcasters provide further information on their programme. Your receiver stores and decodes these data and displays them in the so called Electronic Programme Guide (EPG). This programme preview is activated by using the EPG button. -
Page 13: Settings - Receiver Setup
Settings Press the OK button. Settings The following menu is displayed: Receiver setup Picture Choose the menu item Receiver Setup by pressing Sound confirm by OK. Subtitle OSD configuration Parental lock Settings – Receiver setup The following menu is displayed: Receiver setup Time difference +2.00 Std. -
Page 14: Settings - Picture
Settings Settings – Picture For entering the Picture menu, select menu item Picture in the Settings menu and press OK. The following menu appears: 1) Analog Video Picture The analog video output at the SCART socket can be adjusted by pressing ◄ or ►. You can Analog Video select among following options: FBAS, RGB, or Digital Video... -
Page 15: Settings - Sound
Settings Settings – Sound Sound Sound settings Stereo Sound channel TV Stereo Sound channel Dig. Uncompressed (PCM) 1) Sound setting Using ◄ or ► you can activate following audio modes: Stereo, Mono left or Mono right. 2) Sound channel TV If the broadcasted programme offers different audio options you can select the desired audio output at the TV Scart by keys ◄/►. - Page 16 Settings For entering the OSD configuration menu, please select menu item OSD configuration in the Settings menu and press OK. The following menu appears: OSD Configuration Display time OSD colour blue 1) Display time: By using ◄ or ► you can modify the display duration of the channel change graphics (1-10 seconds).
-
Page 17: Settings - Parental Lock
Settings Settings – Parental lock Your receiver is equipped with a parental lock. This secures the receiver against unauthorised use. When the parental lock is activated, the receiver can only be switched on after entering a 4-digit PIN code. Parental Lock In the Main menu, use the ▲▼... -
Page 18: Installation
Installation Installation In the main menu, select the line Installation using Installation and confirm with OK. The Installation menu ▲ ▼ will appear: Channel search Factory reset Use the buttons to make your selection and confirm with OK. Installation – channel search You can choose between automatic (antenna) and manual (transponder) channel search. -
Page 19: Manual Channel Search
Installation Manual channel search In manual channel search, you can enter the channels to be searched directly. In the Installation menu, move the cursor using the buttons onto the line Channel search and press the OK button. The following menu will appear: Channel search Antenna Cable... -
Page 20: Installation - Smartcard Reader
Installation – Smartcard Reader The Digital-Receiver is optionally equipped with a smartcard reader. With an equal smartcard it is possible to unscramble encoded channels. The smartcard can be inserted also while the receiver is switched on. Insert the smartcard (golden chip on lower side towards the receiver) carefully into the slot at the front panel of the receiver. -
Page 21: Channel List
Channel list Channel list You can resort and/or erase TV and radio channels found in the course of an automatic channel search. This function is Channel list available for all TV and radio channels. Edit main list For entering the corresponding on screen dialog, please Edit favourites list press the Menu key to enter the Main Menu, then select Delete antenna... -
Page 22: Timer
Timer For leaving this menu please press EXIT. If the “Save?” popup appears, please select if you want to store your modifications (Yes) or keep the previous settings (No). Confirm your choice by pressing OK. Timer You can use the record timer functionality to programme a recording for a connected video recorder. -
Page 23: Information
Information If you push one of the buttons or ◄►, following menu appears: Record active. Stop? Choose „Yes“ to stop the record or „No“ to continue the record. Hint: Please make sure that the local time of the receiver is set correctly and the video recorder is programmed, too. -
Page 24: Connection Of External Mass Storage Device
Connection of external mass storage device Connection of external mass storage device If an external mass storage device is connected to the USB-Socket on the rear side of the receiver, it can be managed in the menu “Mass Storage Device”. Important: Before connecting or disconnecting the mass storage device, the receiver must be switched to Standby. -
Page 25: List Of Recordings
List of recordings List of recordings In normal operation, press the Archive button to open up the list of recordings. Deleting recordings You can delete recordings you no longer need from the mass storage device. to select the recording you wish to delete. Then press the red button. -
Page 26: Operating The External Mass Storage Device
In the lower window you will see in the first line the name of the selected programme. Below it, available characters are shown. Use the green button to switch between capital and lower- case letters. In the name, use the red and blue buttons to select the characters you wish to change. The current position that can be changed is highlighted in colour. -
Page 27: Playback
Playback Recordings saved on the mass storage device can be played during timeshift recording. During the timeshift recording, press the Archive button to open the list of recordings. to select the recording you wish to see. Press OK to start the playback. The playback information will be shown on the screen. -
Page 28: Operating The Hard Disk - Setting And Managing Markers
Operating the hard disk – setting and managing markers During the timeshift function or playback, you can mark places on the recording. A marker is shown as a coloured triangle in the status indicator. Press the button F1 at the playback position to set a marker. -
Page 29: Using Serial Interface
Using serial interface Using serial interface The serial data interface “DATA” offers you the possibility to connect the receiver to a PC. Therefore you need a PC and serial cable (On the PC-side a female SUB-D connector with 9 or 25 pins and on Receiver-side a RJ11 plug with 6 pins). Via this connection you can perform software updates and channel lists up- and downloads. -
Page 30: Trouble-Shooting
Trouble-shooting Trouble-shooting Every electric device can have a malfunction. It does not automatically mean that it is defective. In most cases it happens because of a feed cable, plug-and-socket connections or access mistakes. Please control the following items before taking the receiver to your specialised dealer: Problem Possible causes... -
Page 31: Technical Data
Technical data Technical data General 6000 channels On screen video text and VBI video text Fast-OSD quick channel change (zapping) no delay at on screen graphic display big type for better readability concise help for all menus Electronic Programme (EPG) Channel list editor copy, replace, delete blockwise operations... - Page 32 - 32 - - 32 Copyright © 2016 TRIAX. All rights reserved. The TRIAX Logo and TRIAX, TRIAX Multimedia are registered trademarks or trademarks of the TRIAX Company or its affiliates. All specifications in this guide are subject to change without further notice.