Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Triax C-HD207
Summary of Contents for Triax C-HD207
- Page 1 Content Triax C-HD207 Digital Cable-TV Receiver 305207, 305208 Users Guide...
-
Page 2: Table Of Contents
Content Content Content ............................2 General instructions ........................3 Make a contribution to environmental protection ................3 Safety Instructions ......................... 4 Cleaning and care .......................... 4 Control elements, front and rear panel..................5 Connecting the receiver ......................... 6 Remote control ..........................7 Initial installation .......................... -
Page 3: General Instructions
List of recordings .......................... 26 Operating the external mass storage device (Option) ..............27 Recording ..........................27 Timeshift function ........................27 Playback ............................28 Choosing the audio channel for recordings ................28 Fast forward and rewind......................28 Operating the hard disk – setting and managing markers ............ 29 Using serial interface ........................ -
Page 4: Safety Instructions
Safety Instructions Safety Instructions Before installing your digital receiver, all security and operating instructions should be read carefully. The User’s Manual should be retained for future reference. All operating and using instructions should be followed. Never allow children to operate this electrical device without supervisor. ENVIRONMENTAL CONDITIONS Protect the receiver against humidity, heat and cold. -
Page 5: Control Elements, Front And Rear Panel
Control elements, front and rear panel Control elements, front and rear panel 4-digit display shows channel number Display Receiver in standby mode. Channel number Receiver is ON rEC. Timer activated Smartcard reader Connector for mains adapter 12VDC TV-Scart port for connecting the TV HDMI-Output (digital Audio- and Videosignal) for connecting the TV USB-connector for external mass storage device (Option) RF Input Digital –... -
Page 6: Connecting The Receiver
Connecting the receiver Connecting the receiver RF connection Connect the RF Input Digital connector (6) of the receiver to your cable signal wall socket. Connecting a television Use a scart cable to connect the TV connector (3) on the receiver to the corresponding scart connector on the television set. -
Page 7: Remote Control
Remote control Remote control... -
Page 8: Initial Installation
Initial installation Initial installation After reading the safety instructions (see chapter “safety instructions)” and finishing the actions explained in chapter “connecting the receiver” please use the supplied power cord for connecting the apparatus to the power supply. When running the receiver for the first time the “welcome menu”... -
Page 9: Operating The Receiver
Operating the receiver Channel list sorting In the last step of the initial installation you are asked, if the channels which are found during the channel search, should be Welcome sorted automatically. Channel list sorting Note: This function is only effective, if accordant channel list informations are sent by the broadcast-station. -
Page 10: Selecting A Channel
Operating the receiver TV & Radio mode You can choose between the operation mode TV (viewing TV channels) and RADIO (listening to radio channels) by pressing TV/R. Volume control & Muting The volume level can be adjusted by pressing ◄ ► or VOL . The corresponding scale is displayed on the screen. -
Page 11: Epg - Electronic Programme Guide
4. Swap from current channel to the previous one: Your receiver remembers the previous activated channel: - By pressing you can switch from the current to the previous channel - By pressing again switch back to the current channel Every time you perform a channel change, the title and start/stop time of the current and the following programme are displayed in the channel change OSD (on screen display). -
Page 12: Settings - Receiver Setup
Settings previous settings (No). Please choose one of these possibilities by pressing ◄ and ► and confirm your choice by OK. Turn on the receiver by pressing Main menu For entering the main menu, please press the MENU button. Settings The main menu is displayed: Installation Channel list... -
Page 13: Settings - Picture
Settings The initial volume after a power reset of the receiver is adjusted here by pressing ◄ or ►. 4) HDMI Audio Bitstream HDMI Audio Bitstream can be switched ON or OFF by pressing ◄ or ►. 5) Auto Standby Auto-Standby function can be switched ON or OFF by pressing ◄... -
Page 14: Settings - Sound
Settings 4) Display adjustment Use ◄ or ► for adjusting the video signal: pan & scan, letterbox or pillar box. 5) Videosystem Use ◄ or ► for adjusting the video system: AUTO, PAL, NTSC. 6) Picture scaling Here you can choose the picture resolution. 720 x 576 1280 x 720 1920 x 1080... -
Page 15: Settings - Subtitle
Settings Settings – Subtitle Subtitle Subtitle Subtitle language 1) Subtitle By using ◄/► you can activate/deactivate the display of DVB subtitles (if transmitted). 2) Language of the subtitle To select the language of the subtitle you must use ◄ or ►. If there is no subtitle available this is indicated by “-“. -
Page 16: Settings - Parental Lock
Settings Settings – Parental lock Your receiver is equipped with a parental lock. This secures the receiver against unauthorised use. When the parental lock is activated, the receiver can only be switched on after entering a 4-digit PIN code. Parental Lock In the Main menu, use the ▲▼... -
Page 17: Installation
Installation Installation In the main menu, select the line Installation using Installation and confirm with OK. The Installation menu will appear: Channel search Factory reset Use the buttons to make your selection and confirm with OK. Installation – channel search You can choose between automatic (antenna) and manual (transponder) channel search. -
Page 18: Manual Channel Search
Installation Manual channel search In manual channel search, you can enter the channels to be searched directly. In the Installation menu, move the cursor using the buttons onto the line Channel search and press the OK button. The following menu will appear: Channel search Antenna Cable... -
Page 19: Installation - Software Download
Installation Installation – Software download With this function the operating software of the receiver, it´s menu texts and channel list can be updated. Precondition is a Download-channel allocated by your cablenetwork provider. You can gather informations from you cablenetwork provider. Your currently active channel list is not changed by a software update. - Page 20 Installation If you want to update one of the options a.) to c.) press OK at the corresponding menu item. If required by the receiver, it may happen that there are selected additional menu items automatically. In line Information you can specify, if you want to receive further information on the selected data (keys ◄...
-
Page 21: Installation - Smartcard Reader (Option)
Installation – Smartcard Reader The Digital-Receiver is optionally equipped with a smartcard reader. With an equal smartcard it is possible to unscramble encoded channels. The smartcard can be inserted also while the receiver is switched on. Insert the smartcard (golden chip on lower side towards the receiver) carefully into the slot at the front panel of the receiver. -
Page 22: Channel List
Channel list Channel list You can resort and/or erase TV and radio channels found in the course of an automatic channel search. This function is Channel list available for all TV and radio channels. Edit main list For entering the corresponding on screen dialog, please Edit favourites list press the Menu key to enter the Main Menu, then select Delete all channels... -
Page 23: Timer
Timer Timer You can use the record timer functionality to programme a recording for a connected video recorder. Totally 10 record timers can be activated. Or you can use the sleep timer to specify a time at which the Timer receiver is to switch into standby mode. -
Page 24: Information
Information Information Enter the main menu, there use to select line Information and press OK. In the upper section of the menu the channel parameters of the activated channel are displayed. In the lower section of the menu the signal qualities are displayed. - C/N: The further the bar turns right and the higher the dB value, the better the signal quality. -
Page 25: Connection Of External Mass Storage Device (Option)
Connection of external mass storage device (option) Connection of external mass storage device (option) If an external mass storage device is connected to the USB-Connector (option) on the rear side of the receiver, it can be managed in the menu “Mass Storage Device”. Important: Before connecting or disconnecting the mass storage device, the receiver must be switched to Standby. -
Page 26: List Of Recordings
List of recordings List of recordings In normal operation, press the Archive button to open up the list of recordings. Deleting recordings You can delete recordings you no longer need from the mass storage device. to select the recording you wish to delete. Then press the red button. -
Page 27: Operating The External Mass Storage Device (Option)
In the lower window you will see in the first line the name of the selected programme. Below it, available characters are shown. Use the green button to switch between capital and lower- case letters. In the name, use the red and blue buttons to select the characters you wish to change. The current position that can be changed is highlighted in colour. -
Page 28: Playback
Playback Recordings saved on the mass storage device can be played during timeshift recording. During the timeshift recording, press the Archive button to open the list of recordings. Use to select the recording you wish to see. Press OK to start the playback. The playback information will be shown on the screen. -
Page 29: Operating The Hard Disk - Setting And Managing Markers
Operating the hard disk – setting and managing markers During the timeshift function or playback, you can mark places on the recording. A marker is shown as a coloured triangle in the status indicator. Press the button F1 at the playback position to set a marker. -
Page 30: Trouble-Shooting
Trouble-shooting Trouble-shooting Every electric device can have a malfunction. It does not automatically mean that it is defective. In most cases it happens because of a feed cable, plug-and-connector connections or access mistakes. Please control the following items before taking the receiver to your specialised dealer: Problem Possible causes... -
Page 31: Technical Data
Technical data Technical data General 6000 channels On screen video text and VBI video text Fast-OSD quick channel change (zapping) no delay at on screen graphic display big type for better readability concise help for all menus Electronic Programme (EPG) Channel list editor copy, replace, delete blockwise operations... - Page 32 2006/95/EC (repealing the 73/23/EEC Directive, amended by the 93/68/EEC Directive) and 2004/108/EC (repealing 89/336/EEC Directive) Directives. Svend Kristiansen Quality Manager Triax A/S Bjørnkærvej 3 8783 Hornsyld Danmark Electric and electronic equipment and included batteries contains materials, components and substances that can be hazardous to your health and the environment, if the waste material (discarded electric and electronic equipment and batteries) is not handled correctly.