Table of Contents
Advertisement
3: In
OFF
4: Fu
GA
Display
Default
5: St
ON
6: OH
68 F
7: OL
5 F
8: FH
00
9: FL
00
10: dr
NO
11: dI
NO
12: bt
0
13: Ft
1
14: bo
27 F
15: OF
68 F
16: cH
180 F
17: cL
86 F
18: dH
140 F
19: cb
100
20: db
100
21: PP
40
22: Po
5
23: PF
10
24: SF
158 F
Initialized system
Change unit for water
volume
Detail
Stored water heating
function "ON", "OFF"
Maximum Outdoor
Temperature
Minimum Outdoor
Temperature
Maximum Fan speed
Minimum Fan speed
Initialized burner
operation time
Initialized ignition cycle
Boost Function
CH Anti-Frequency time
Set differential
temperature to turn
burner "ON"
Warm Weather
Shutdown
Maximum supply
temperature
Minimum supply
temperature
Maximum DHW set
temperature
Heating capacity
DHW capacity
Internal CH Pump Post
Run Timer,
T/T Calling for Heat
Internal CH Pump
Overrun Timer (On)
Internal CH Pump
Overrun Timer (Off)
Internal DHW Storage
Tank Setpoint
Select "ON" to reset to factory setting
(Burner operation time, Ignition cycles, and Supply power time will not be
Select "OFF" to turn off this function
When used with an outdoor sensor, sets the maximum outdoor design
temperature for the system design. Maximum outdoor temperature must be
o
set 9
F above the minimum outdoor temperature.
Range: (Minimum Outdoor Temperature + 9
Sets the minimum outdoor design temperature for the system. Minimum
outdoor temperature must be set 9
o
Range: -4
F to (Maximum Outdoor Temperature - 9
Adjusts Maximum Fan Speed
Adjusts Minimum Fan Speed
Select ON to Initialize burner operation time
Select ON to Initialize ignition cycles
This function boosts CH temperature to the maximum if set point is not
reached within the set period of time.
This function delays burner operation during CH mode
When set, the appliance will operate to heat CH water when water
temperature falls below a differential setting.
Example: If setpoint is 180
on when CH water temperature falls below 153
Warm weather shut down will shut down CH Mode if the programmed
outdoor temperature is exceeded.
Sets the maximum design supply temperature based on the minimum
outdoor design temperature. Maximum supply temperature must be set 9
above the minimum supply temperature.
Range: (Minimum Supply Temperature + 9
Sets the design supply water temperature based on the maximum outdoor
design temperature. Minimum supply temperature must be set 9
the maximum supply temperature.
o
Range: 86
F to (Maximum Supply Temperature - 9
Sets Maximum DHW Setpoint temperature
Set Heating combustion rate
NOTE: 199F Models shall be factory set at 70%. The default number will be
70. This percentage can be increased with an additional pump.
Set DHW combustion rate
When appliance CH setpoint is satisfied, but T/T is calling for heat, the
burner will shut OFF and the CH pump will continue to run for this set
Range: 1 ~ 60 minutes
This function runs the Internal CH Pump after the Internal CH Pump Post
Run Timer has completed. This will cycle the Internal CH Pump again
based on the default programmed Off and On cycles and repeats until the
central heating call is satisfied.
Sets the Internal DHW Storage Tank Setpoint
reset)
Range: ON or OFF
Range: GA or Li
Description
Range: ON or OFF
o
F below the maximum outdoor
temperature.
Range: -30 - +30
Range: -30 -+30
Range: NO or YES
Range: NO or YES
Range: 0 - 120 min
Range: 0 - 20 min
o
o
F and differential is 27
F, the appliance will turn
o
Range: 9 - 27
F
o
Range: 50 - 110
F
o
o
Range:120 - 140
F
Range: 50 - 100%
Range: 50 - 100%
amount of time
Range: 1~60 minutes
o
Range:140 ~ 167
F
WHL-015 REV. 1.13.17
54
o
o
F) to 110
F
o
F)
o
F.
o
F
o
F) - 180
F
o
F below
o
F)
Advertisement
Table of Contents
