Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Fluke Calibration P3000 Series
Summary of Contents for Fluke Calibration P3000 Series
- Page 1 P3000 Series Pneumatic Deadweight Tester Users Manual PN 3952260 November 2010 © 2010 Fluke Corporation. All rights reserved. Printed in USA. Specifications are subject to change without notice. All product names are trademarks of their respective companies.
- Page 2 LIMITED WARRANTY AND LIMITATION OF LIABILITY Each Fluke product is warranted to be free from defects in material and workmanship under normal use and service. The warranty period is one year and begins on the date of shipment. Parts, product repairs, and services are warranted for 90 days.
-
Page 3: Table Of Contents
Table of Contents Chapter Title Page General Information ................1-1 Introduction......................1-1 How to Contact Fluke ..................1-1 Safety Information ..................... 1-1 Safety Summary .................... 1-1 Compressed Gas .................... 1-2 Heavy Weights ....................1-2 Personal Protective Equipment..............1-2 Symbols Used in this Manual ................1-2 Operating Principle .................... - Page 4 P3000 Series Users Manual Maintenance & Servicing ..............5-1 Introduction......................5-1 PCU Assembly — 10 mm Nominal Diameter — Pressure ....... 5-1 Piston Disassembly..................5-1 Piston Cleaning....................5-1 Piston Re-Assembly ..................5-2 Replacement PCU Assembly ................ 5-2 PCU Assembly — 10 mm Nominal Diameter — Vacuum ....... 5-3 Piston Disassembly..................
- Page 5 List of Tables Table Title Page 1-1. Symbols........................1-2 1-2. Operation and Storage Specifications ..............1-3 2-1. Test Port Inserts - Parts List ................... 2-5 5-1. PCU Assembly - 10 mm - Pressure - Parts List ............. 5-3 5-2. PCU Assembly - 10 mm - Vacuum - Parts List ............. 5-5 5-3.
- Page 6 P3000 Series Users Manual...
- Page 7 List of Figures Figure Title Page 1-1. Single PCU Instrument ..................1-4 1-2. Single PCU Instrument with Handpump..............1-5 1-3. Dual PCU (Pressure & Vacuum) Instrument ............1-5 1-4. Dual PCU (Pressure & Vacuum) Instrument with Handpump ......1-6 1-5. Vacuum Instrument ....................
- Page 8 P3000 Series Users Manual...
-
Page 9: General Information
Chapter 1 General Information Introduction This User’s Manual covers the following pressure instruments: P3011, P3011P, P3012P, P3013P, P3014P, P3015, P3015P, P3022, P3022P, P3023, P3023P, P3025, and the P3025P. How to Contact Fluke To order accessories, receive operating assistance, or get the location of the nearest Fluke distributor or Service Center, call: •... -
Page 10: Compressed Gas
P3000 Series Users Manual Compressed Gas Use of compressed gas can create an environment of propelled foreign matter. Pressure system safety precautions apply to all ranges of pressure. Care must be taken during testing to ensure that all connections are properly and tightly made prior to applying pressure. -
Page 11: Operating & Storage Specification
General Information Environmental Corrections When the gas pressure within the system balances the combined downward force of the piston and weights, the piston and weights will float freely and the system is in equilibrium. The design of a Piston/Cylinder Unit (PCU) fitted to a deadweight tester allows for a very small clearance gap between the piston and cylinder. -
Page 12: Model Variations
TRUE PRESSURE TRUE PRESSURE Model Variations This manual covers many pressure ranges and models within the P3000 series of instruments. The following illustrations detail the physical appearance of the six basic models: Model 3015 gjn024.bmp Figure 1-1. Single PCU Instrument... - Page 13 General Information Model Variations Model 3012P, 3013P, 3014P and 3015P gjn025.bmp Figure 1-2. Single PCU Instrument with Handpump Model 3022, 3023 and 3025 gjn026.bmp Figure 1-3. Dual PCU (Pressure & Vacuum) Instrument...
- Page 14 P3000 Series Users Manual Model 3022P, 3023P and 3025P gjn027.bmp Figure 1-4. Dual PCU (Pressure & Vacuum) Instrument with Handpump Model 3011 gjn028.bmp Figure 1-5. Vacuum Instrument...
- Page 15 General Information Model Variations Model 3011P gjn029.bmp Figure 1-6. Vacuum Instrument with Handpump...
- Page 16 P3000 Series Users Manual...
-
Page 17: Preparation
Chapter 2 Preparation Introduction The deadweight tester must be set up on a level, stable workbench or similar surface. If instrument has fitted handpump, remove pump handle form tool roll and fit to pump arm. Level the tester using the four adjustable feet to the bubble level attached to the top plate. Connection to External Pressure/Vacuum Supplies Connection ports in the rear panel of the instrument are 1/4 NPT. -
Page 18: Connections
P3000 Series Users Manual Connections Fit the device under test (DUT) to the test port using the method described below: W Warning DO NOT use Teflon/PTFE tape on these connections, as this will prevent correct sealing. The Gauge Adapter sealing system is designed for hand-tight sealing up to 20,000 psi / 1,400 bar-wrenches or similar tools are not required —... - Page 19 Preparation Connections gjn007.bmp Figure 2-2. Connect Assembly to Test Port gjn008.bmp Figure 2-3. Hand-Tighten Only 3. To adjust the position to face forward, hold the gauge adapter and turn the instrument COUNTER-CLOCKWISE, so that it faces forward.
- Page 20 P3000 Series Users Manual gjn009.bmp Figure 2-4. Adjust Gauge Position 4. Hold the instrument steady, whilst turning the gauge adapter COUNTER-CLOCKWISE until it pulls down onto the O-ring. gjn010.bmp Figure 2-5. Tighten Gauge...
-
Page 21: Test Port Insert
Preparation Connections Test Port Insert For devices with 1/8 BSP or NPT mounting threads, the diameter of the thread is very close to the effective sealing diameter of the O-ring fitted to the test port. This can make it difficult to achieve a good seal. When mounting these devices, use the test port insert (stored in the spare seals container) as shown in Figure 2-6. - Page 22 P3000 Series Users Manual...
-
Page 23: Operation
Chapter 3 Operation Introduction All P3000 Series pneumatic deadweight testers have a monitor gauge fitted to the instrument top plate, to serve as a guide to the operator by indicating the approximate pressure in the system. Single PCU Models — Pressure 1. -
Page 24: Single Pcu Models - Vacuum
P3000 Series Users Manual 8. Depressurize the system by SLOWLY opening the Exhaust valve, as sudden depressurization will cause the weight stack to fall quickly, which may damage the piston assembly. 9. Remove the weights from the piston. Single PCU Models — Vacuum 1. - Page 25 Operation Dual PCU (Pressure & Vacuum) Models 3. If either the system or handpump selector valve is set for vacuum, when pressure is applied to the system, the safety valve fitted to the front of the PCU mounting assembly will be ejected, venting the system. (The safety valve is retained by the assembly, and will not “fly-out”...
- Page 26 P3000 Series Users Manual...
-
Page 27: Calibration In Different Pressure Units
Chapter 4 Calibration in Different Pressure Units Introduction The deadweight tester can be used to calibrate in different pressure units in either of two methods. Conversion Weights A set of Conversion Weights can be supplied, marked in the required pressure unit, and adjusted to the correct mass for use with the existing piston(s). - Page 28 P3000 Series Users Manual...
-
Page 29: Maintenance & Servicing
Chapter 5 Maintenance & Servicing Introduction Note The piston/cylinder assembly is the most critical and sensitive part of the deadweight tester. To maintain accuracy, the piston must always slide freely in the cylinder, and the gas supply must remain clean and dry. The Figures on the following pages detail the components of each assembly, together with the relevant part numbers. -
Page 30: Piston Re-Assembly
P3000 Series Users Manual W Caution Never touch the working surface of a clean piston with bare fingers — the natural oil in your skin can cause the piston and cylinder to stick. 8. Wipe any dirt or moisture from the outside surfaces of the cylinder (2). -
Page 31: Pcu Assembly - 10 Mm Nominal Diameter - Vacuum
Maintenance & Servicing PCU Assembly — 10 mm Nominal Diameter — Vacuum gjn31.eps Figure 5-1. PCU Assembly - 10mm - Pressure Table 5-1. PCU Assembly - 10 mm - Pressure - Parts List Item Description Part Item Description Part Weight Carrier Spec Piston Spec... -
Page 32: Piston Re-Assembly
P3000 Series Users Manual 5. After removal from the solvent, using a NEW tissue, repeat the cleaning procedure in step 3, taking great care to ensure that all traces of solvent are removed from the inside of the tubular piston and weight carrier. -
Page 33: Pcu Assembly - 16 Mm Nominal Diameter
Maintenance & Servicing PCU Assembly — 16 mm Nominal Diameter gjn32.eps Figure 5-2. PCU Assembly - 10mm - Vacuum Table 5-2. PCU Assembly - 10 mm - Vacuum - Parts List Item Description Part Item Description Part Piston Spec Bonded Seal 3918392 Cylinder Spec... -
Page 34: Piston Re-Assembly
P3000 Series Users Manual 6. After removal from the solvent, using a NEW tissue, repeat the cleaning procedure in step 4, take great care to ensure that all traces of solvent are removed from inside the tubular piston. 7. Place piston carefully on a NEW tissue where it will not be damaged while the cylinder is cleaned. -
Page 35: Pcu Assembly - 22 Mm Nominal Diameter
Maintenance & Servicing PCU Assembly — 22 mm Nominal Diameter gjn33.eps Figure 5-3. PCU Assembly - 16 mm Table 5-3. PCU Assembly - 16 mm - Parts List Item Description Part Item Description Part Piston Spec O Ring 3864766 Bearing 3918063 Piston Stop Spec... -
Page 36: Piston Re-Assembly
P3000 Series Users Manual 6. After removal from the solvent, using a NEW tissue, repeat the cleaning procedure in step 4, take great care to ensure that all traces of solvent are removed from inside the tubular piston. 7. Place piston carefully on a NEW tissue where it will not be damaged while the cylinder is cleaned. -
Page 37: Top Plate Removal
Maintenance & Servicing Top Plate Removal gjn34.eps Figure 5-4. PCU Assembly - 22 mm Table 5-4. PCU Assembly - 22 mm - Parts List Item Description Part Item Description Part Piston Spec Bearing Cap 3918182 Cylinder Spec O Ring 3867509 Top Plate Removal Note In order to perform maintenance procedures on the hydraulic system, the... -
Page 38: Handpump Assembly
P3000 Series Users Manual W Caution When handling the top plate assembly, it is good practice to remove the piston assemblies to avoid accidental damage. Note Replacement is simply the reverse of the above procedure. Handpump Assembly Disassembly 1. Disconnect tubing from check valve (19) and/or (23). - Page 39 Maintenance & Servicing Handpump Assembly 14 15 17 18 gjn35.eps Figure 5-5. Handpump Assembly Table 5-5. Handpump Assembly - Parts List Item Description Part Item Description Part Spring Clip 3920224 Cylinder Spec Clevis 3920236 Bonded Seal 3918879 Locknut 3918713 O Ring 3865075 Set Screw 3918822...
-
Page 40: System Selector Valve
P3000 Series Users Manual System Selector Valve Before commencing disassembly of the selector valve, make a note of the tubing connections to avoid problems during reassembly. Disassembly 1. Disconnect nylon tubing from connectors (11). 2. Loosen set screws (1), and remove knob (2) from valve shaft (3). -
Page 41: Safety Valve
Maintenance & Servicing Safety Valve gjn36.eps Figure 5-6. System Selector Valve Table 5-6. System Selector Valve - Parts List Item Description Part Item Description Part Set Screw 3927102 Valve Rotor 3921856 3927125 Knob Screw 3908867 Valve Shaft 3921842 Bonded Seal 3921935 3906008 Connector... - Page 42 P3000 Series Users Manual gjn37.eps Figure 5-7. Safety Valve Table 5-7. Safety Valve - Parts List Item Description Part Item Description Part Safety Valve 3919354 Screw 3908578 O Ring 3865142 Bonded Seal 3921964 Safety Plug 3919331 Vacuum Body 3921817 Plug Retainer...
-
Page 43: Fault Finding
Chapter 6 Fault Finding Poor PCU Spin/Sensitivity The clean pneumatic piston/weight carrier assembly will rotate freely, without additional weights, slowing down gradually to a complete stop. If the rotation stops quickly, then the PCU may be dirty and require cleaning. If the piston “squeaks” when rotated, it must be cleaned immediately, see Chapter 5, Maintenance &... -
Page 44: High Pcu Fall-Rate
P3000 Series Users Manual High PCU Fall-Rate The piston will always fall slowly as the gas passes between the piston and cylinder. However, this fall rate will never be so fast that a stable reading cannot be made. 1. The system may be leaking. Check that exhaust valve is fully closed, and test port connections are correctly made. -
Page 45: Storage & Transportation
Chapter 7 Storage & Transportation Instrument 1. Shut-off any external supplies, and depressurize system by slowly opening both Inlet and Exhaust valves. 2. Disconnect external supplies. 3. Remove screw-in handle from handpump arm (if fitted) and store in tool roll. 4. - Page 46 P3000 Series Users Manual...
-
Page 47: Ancillary Equipment
Chapter 8 Ancillary Equipment Dirt/Moisture Trap, P5531 If there is any doubt that the instrument to be tested is not internally clean, then the addition of the P5531 Dirt/Moisture Trap will protect the deadweight tester from contamination and possible damage. Any particles or moisture present within the DUT will fall into the clear, acrylic chamber, where they can be seen by the operator. -
Page 48: Angle Adapter, P5543
P3000 Series Users Manual Angle Adapter, P5543 To calibrate gauges with the pressure connection on the rear (e.g. panel-mount gauges) in their correct position, an angle adapter should be used. The angle adapter fits directly onto the test station, converting it through 90 degrees, allowing the standard adapters to be used.