Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ubiquiti airMAX NanoBridge M NBM3
Summary of Contents for Ubiquiti airMAX NanoBridge M NBM3
- Page 1 High-Performance airMAX Bridge ™ Model: NBM3/NBM365/NBM900...
-
Page 2: Package Contents
Guide Products may be different from pictures and are subject to change without notice. TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet cable and earth grounding must be used as conditions of product warranty. TOUGHCable is designed for outdoor installations. -
Page 3: Hardware Overview
Hardware Overview NBM3/NBM365 Ports Main Secondary Reset Secondary Port This 10/100 Ethernet port is used for bridging. Main Port This 10/100 Ethernet port is used to connect the power and should be connected to the LAN and DHCP server. Reset Button To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the NanoBridge is already powered on. - Page 4 NBM900 Ports RP-SMA Reset RP-SMA Connector Reserved for future use. LAN Port The 10/100 Ethernet port is used to connect the power and should be connected to the LAN and DHCP server. Reset Button To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the NanoBridge is already powered on.
- Page 5 NBM3/NBM365 LEDs LAN1 LAN2 Power The Power LED will light green when the device is connected to a power source. LAN1 Main The LAN1 Ethernet LED will light steady green when an active Ethernet connection is made to the Main Port and flash when there is activity.
- Page 6 NBM900 LEDs Power The Power LED will light green when the device is connected to a power source. Ethernet The Ethernet LED will light steady green when an active Ethernet connection is made and flash when there is activity. Signal In airOS, you can modify the wireless signal strength threshold values for each LED on the Advanced tab under Signal LED...
-
Page 7: Installation Requirements
AC ground of the PoE. We recommend that you protect your networks from the most brutal environments and devastating ESD attacks with industrial-grade shielded Ethernet cable from Ubiquiti Networks. For more details, visit www.ubnt.com/toughcable Using the Correct Feed Support Tube The NanoBridgeM3/M365 and NanoBridgeM900 require different Feed Support Tubes, which are not interchangeable. -
Page 8: Installation
Installation The installation instructions show the NBM900; however, the same instructions apply to the NBM3 and NBM365. 1. Attach the Feed Support Tube to the Dish Bracket using the M8x50 Carriage Bolt, M8 Serrated Flange Nut, M6x15 Carriage Bolt, and M6 Serrated Flange Nut. - Page 9 2. Attach the Dish Bracket to the Dish Reflector using the four M6x12 Carriage Bolts and four M6 Flange Nuts.
- Page 10 3. Attach the Mounting Bracket to the Dish Bracket using the four M8x15 Carriage Bolts and four M8 Flange Nuts. 4. Install the NanoBridge by lining up the mounting tabs of the NanoBridge with the slots on the Feed Support Tube. Then slide the NanoBridge into place.
- Page 11 5. Attach the Dish Assembly to the pole using the two U-Bolts, two Pole Clamps, and four M8 Flange Nuts. Note: The mounting assembly can accommodate a Ø 1.25" - 2.25" pole. 6. Slide open the cover of the NanoBridge. Connect the Ethernet cable to the Ethernet port of the NanoBridge.
- Page 12 7. Connect the other end of the Ethernet cable from the NanoBridge to the Ethernet port labeled POE on the PoE Adapter. 8. Connect an Ethernet cable from your LAN or computer to the Ethernet port labeled LAN on the PoE Adapter. 9.
- Page 13 Accessing airOS Verify connectivity in the airOS Configuration Interface. 1. Make sure that your host machine is connected via Ethernet to the NanoBridge. 2. Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet. 3.
-
Page 14: Installer Compliance Responsibility
Since Ubiquiti Networks equipment can be paired with a variety of antennas and cables, the Antenna (if applicable) and Output Power fields are provided to the professional installer to... -
Page 15: Specifications
Specifications NBM3/NBM365/NBM900 Dimensions NBM3/NBM365 492 x 440 x 705 mm NBM900 543 x 440 x 725 mm Weight NBM3/NBM365 0.9 kg (Radio) 5.088 kg (Dish and Mount Included) NBM900 1.310 kg (Radio) 5.578 kg (Dish and Mount Included) Operating Frequency NBM3 3400 - 3700 MHz NBM365... -
Page 16: Safety Notices
Safety Notices Read, follow, and keep these instructions. Heed all warnings. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. -
Page 17: Limited Warranty
(VI) has no original Ubiquiti MAC label, or is missing any other original Ubiquiti label(s). (VII) has not been received by Ubiquiti within 30 days of issuance of the RMA. -
Page 18: Limitation Of Liability
SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS, DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY OF THE FOREGOING. - Page 19 Note Some countries, states and provinces do not allow exclusions of implied warranties or conditions, so the above exclusion may not apply to you. You may have other rights that vary from country to country, state to state, or province to province. Some countries, states and provinces do not allow the exclusion or limitation of liability for incidental or consequential damages, so the above limitation may not apply to you.
-
Page 20: Industry Canada
Industry Canada This Class A digital apparatus complies with Canadian ICES-003. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. - Page 21 RoHS/WEEE Compliance Statement English European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams.
- Page 22 Español La Directiva 2002/96/CE de la UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
-
Page 23: Declaration Of Conformity
UBIQUITI NETWORKS device, megfelel a vonatkozó alapvetõ [Hungarian] követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. Íslenska Hér me l sir UBIQUITI NETWORKS yfir ví a UBIQUITI NETWORKS device, er í samræmi vi grunnkröfur og a rar kröfur, sem ger ar eru í [Icelandic] tilskipun 1999/5/EC. -
Page 24: Online Resources
NETWORKS device, è conforme ai requisiti essenziali ed alle altre [Italian] disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski Ar o UBIQUITI NETWORKS deklar , ka UBIQUITI NETWORKS device, atbilst Direkt vas 1999/5/EK b tiskaj m pras b m un citiem ar to saist [Latvian] tajiem noteikumiem.
Need help?
Do you have a question about the airMAX NanoBridge M NBM3 and is the answer not in the manual?
Questions and answers