As A Band Pa - Yamaha powered mixer Owner's Manual

As a band PA

Here is an example of using the EMX66M as a small PA for a band. In this example, the monitor speakers are
being sent a mix that is independent of the MAIN speaker mix. An external effect such as delay or reverb is
also being used.
Connections
• Connect mics or instruments, such as keyboards,
to the channel input jacks 1–6.
• Connect the main speakers to the SPEAKERS A
1/2 jacks, and connect the monitor speakers to
the SPEAKERS B 1/2 jacks. Then, set the power
amp select switch to "MAIN-MON."
• If you will be using an external effect such as
delay or reverb, connect the EMX66M's EFFECT
OUT jack to the input jack of the external effect,
and connect the output jack of the external effect
to the EMX66M's AUX IN jack.
1
HIGH
–15 +15
MID
–15 +15
LOW
–15 +15
MONITOR
0
+15
EFFECT
0 +15
LEVEL
0
PAD
1
Hi-Z
Low-Z
Microphone
Keyboard
Main Speakers
1 SPEAKERS A 2
2 3 4 5 6
HIGH HIGH HIGH HIGH HIGH
–15 +15 –15 +15 –15 +15 –15 +15 –15 +15
MID MID
MID MID MID
–15 +15 –15 +15 –15 +15 –15 +15
–15 +15
LOW LOW LOW LOW LOW
–15 +15 –15 +15
–15 +15 –15 +15 –15 +15
MONITOR MONITOR MONITOR MONITOR MONITOR
0 0
+15 0 +15 0 +15 +15 0 +15
EFFECT EFFECT EFFECT EFFECT EFFECT
0 +15 0 +15 0 +15 0 +15 0 +15
LEVEL LEVEL LEVEL LEVEL LEVEL
10 0 10 0 10 0 10 0 10 0 10
PAD PAD PAD PAD PAD
2 3 4 5 6
LINE Super Hi-Z
1 1
Hi-Z Hi-Z EFFECT OUT
Hi-Z
2 2
Low-Z Low-Z Low-Z MIC
MIC
Electric
Note: Set the power amp select switch of the POW-
ER AMP section to the "MAIN MON" position. If
you are using an external effect, we recommend that
you turn down the EFFECT RTN controls of the
MAIN and MONITOR sections. If the external ef-
fect has a stereo output, it is possible to connect its
output jacks to the LINE jacks of channels 5. How-
ever in this case, be sure that the EFFECT controls
are turned all the way down for the channels into
which the effect sound is being input. If the EFFECT
controls are raised, feedback will occur, and your
speakers may be damaged.
Monitors Speakers
1 SPEAKERS B
DIGITAL
EFFECT
+6
+12 +12
+3
6 6
0
0 0
-5
6 6
VOCAL ECHO 1 –12 –12 -10
125 250 500 1k 2k 4k 8k
VOCAL ECHO 2 GEQ
POWER AMP
VOCAL
REVERB 1
VOCAL
0 10 0 10
REVERB 2 0 10
2TR IN MASTER
EFFECT RTN
MAIN
HALL 1 MONITOR
MAIN
HALL 2
+12 +6
+12
6 6 +3
ROOM 0 0 0
6 6 -5
–12 –12
PLATE -10
125 250 500 1k 2k 4k 8k
GEQ
ON
0 10 0 10 0 10
0 10
EFFECT RTN AUX IN
2TR IN MASTER
MAIN
EFFECT
INPUT TO MAIN OUT PUT
EEEngine
2TR REC
IN OUT
1 1
MAIN
FOOT SW AUX IN
MONITOR
2 2
SEE REAR PANEL CAUTION
88
Effects Processor
Electric-acoustic
guitar
bass
Example setups
2
Power amp
PHANTOM
select switch
ON
OFF
MAIN
MON
MAIN MAIN
LIMITER
MAIN
MON
MAIN
BRIDGE
MAIN
BRIDGE
A
B
YAMAHA
SPEAKER
PROCESSING
power
ON /
OFF
*1
Footswitch
(YAMAHA FC5)
*1. Although this example shows an ex-
ternal effects processor and foot-
switch, which is used to turn on and
off the built-in digital effects proces-
sor, connected to the EMX66M, in
practice, only one effects processor,
internal or external, will be used at a
time, so the footswitch is not required
when using external effects.
EMX66M—Owner's Manual
21