Speaker Setting - Yamaha DVD-S1200 Owner's Manual

Main (L)
SETUP
Exit
SELECT
Test
signal
ENTER RETURN
(L)
A
No
B
L
LS
Center speaker
Difference
Approx. 50 cm (1 1 /
2
Approx. 100 cm (3 feet)
Approx. 150 cm (5 feet)
Approx. 200 cm (6 feet)
Rear speakers
Difference
Approx. 200 cm (6 feet)
Approx. 400 cm (12 feet)
Approx. 600 cm (18 feet)
32
AUDIO/VIDEO
POWER OPEN/CLOSE
/ I
Í
1 2 3 4
5 6 7 8
CANCEL
9 0 1 0
S
SET UP MARKER
VIDEO OFF GROUP PAGE TEXT
TOP MENU MENU
DIRECT NAVI PLAY LIST
Cursor
ENTER ENTER
ON SCREEN RETURN
buttons/ENTER
PLAY MODE SUBTITLE AUDIO ANGLE
Center
Main (R)
a b a c a
L R
ms C dB
0 0
Exit
dB
SW
Test 0
dB ms dB
LS RS
0 0 0
Rear
a c b c a
(L) (R) (R)
LS
LS
Large Small
R
C
d
e
SW
f
RS
Setting
feet) 1.3 ms
2.6 ms
3.9 ms
5.3 ms
Setting
5.3 ms
10.6 ms
15.9 ms
Changing settings

Speaker setting

Change speaker size and presence
balance to suit the speakers you have connected.
These settings are not necessary when you select "2-channel"
(only two speakers are connected).
Speaker presence and size ( )
1. Press the cursor buttons [ ,
press [ENTER].
2. Press the cursor buttons [ ,
press [ENTER].
Icon examples: Rear speaker (L)
Large: When the speaker supports low-frequency (under 100 Hz)
reproduction.
Small: Select when the speaker does not support low-frequency
reproduction.
The size setting for the main speakers is automatically determined
by the setting for the subwoofer.
Delay time ( )
B
(Dolby Digital, center and rear speakers only)
For optimum listening with 5.1-channel sound, all the speakers, ex-
cept for the subwoofer, should be the same distance from the seat-
ing position. If you have to place the center or rear speakers closer
to the seating position, adjust the delay time to make up for the dif-
ference.
If distance (from the center speaker) and
ers) are the same as or greater than
leave the delay time as "0", the factory preset.
If either distance
relevant table and change to the recommended setting.
Subwoofer
Changing the delay time
c a
1. Press the cursor buttons [ ,
time box and press [ENTER].
2. Press the cursor buttons [ ,
press [ENTER].
Speaker balance ( )
1. Press the cursor buttons [ ,
press [ENTER].
A test signal is output from one speaker at a time, starting with
the main left speaker and proceeding clockwise.
MAIN (L)>CENTER>MAIN (R)
:
REAR (L)(-----------==REAR (R)
2. While listening to the test signal, press the cursor buttons
[ , ] to adjust the volume of the center and rear speakers
so they are the same apparent volume as the main speakers
( 6 dB to
(The main speakers cannot be adjusted here.)
3. Press [ENTER].
The test signal stops.
Note
Test signal is effective only when you made analog connection.
When you make digital connection, make adjustment using the
test tone on the amplifier.
No signal is output for the subwoofer. To adjust its volume, play
something, then return to this screen to adjust to suit your taste.
When you are finished
Press the cursor buttons [ ,
[ENTER].
Note
The unit may be unable to output as set here due to limitations im-
posed by the unit itself or the disc being played. (The FL display's
"P.PCM" indicator lights or "D.MIX" indicator goes out in these
cases.)
, delay time
, , ] to select the item and
] to select the setting and
(from the rear speak-
(from the main speakers),
or is less than , find the difference in the
, , ] to select the delay
] to adjust the delay time and
, , ] to select "Test" and
;
6 dB).
, , ] to select "Exit" and press
, and channel