Subscribe to Our Youtube Channel
Related Manuals for Triton Blue MegaBeam G10B
Summary of Contents for Triton Blue MegaBeam G10B
- Page 1 PROFESSIONAL MOVING HEAD USER MANUAL MegaBeam G10B KEEP THIS MANUAL FOR FUTURE NEEDS...
-
Page 2: Table Of Contents
Contents 1. Features ................................2 2. Overview ................................3 3. SAFETY INSTRUCTIONS ..........................3 3.1) Important safety warns ......................... 3 3.2) GENERAL GUIDELINES ........................4 4. INSTALLATION INSTRUCTIONS ......................5 4.1) Installing or replacing the lamp ......................5 4.2) Mounting the device ..........................7 Installation via the Omega holders ..................... -
Page 3: Features
Thank you for your patronage. We are confident that our excellent products and service can satisfy you. For your own safety, please read this user manual carefully before installing the device. In order to install , operate, and maintain the lighting safety and correctly. We suggest that the installation and operation should be done by the verified technician and follow the instruction strictly. -
Page 4: Overview
2. Overview 1) Lens 2) Microphone 3) Display 4) Left-button 5) Down-button 6) ENTER-button 7) Right-button 8) Mode/Esc-button 9) Up-button 10) Handle 11) RJ45 In 12) RJ45 Out 13) 3-Pin DMX In 14) 3-Pin DMX Out 15) Power In 16) Power Out 17) Fuse 3. -
Page 5: General Guidelines
Make sure the power cord is never crimped or damaged by sharp edges. If this would be the case, replacement of the cable must be done by an authorized dealer. Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the power cord by the plug. -
Page 6: Installation Instructions
4. INSTALLATION INSTRUCTIONS 4.1) Installing or replacing the lamp O nl y i nstal l the l am p w i th the dev i c e unpl ug g ed f rom the m ai ns. T he l am p has to be repl ac ed w hen i t i s dam ag ed or deform ed. ... - Page 7 For the installation, you need one: MSD Platinum 17 RA Procedures: 1）Please put the fixture on a smooth desk, 2）First, take off the upper and down cover from the lamp head, release the three screws that the letter A pointed to, then it can take down the plate of lamp-socket. 3）Before taking off the lamp, please release the two red wires which connect to the lamp.
-
Page 8: Mounting The Device
4.2) Mounting the device The applicable temperature for the lighting is between -10°C to 45°C. Do not use the lighting under or above the temperature. The installation of the effect has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation. - Page 9 a) Fixed the clamp on the bracket by tighten up the M12 screw on the bracket to the Ф13 hole in the middle of the bracket. b) Insert the quick-lock fasteners of the first Omega holder into the respective holes on the bottom of the device.
- Page 10 Layout Drawings: XM1093-V1.2.0-NR...
-
Page 11: Dmx-512 Control Connection
Mounting points Be sure this fixture is kept at least 15m away from any flammable materials (decoration etc.). Always use and install the supplied safety cable as a safety measure to prevent accidental damage and/or injury in the event the clamp fails. Overhead mounting requires extensive experience, including amongst others calculating working load limits, a fine knowledge of the installation material being used, and periodic safety inspection of all installation material and the fixture. -
Page 12: Dmx-512 Connection With Dmx Terminator
Address 1 Address 15 Address 29 Ø Max number of tandem： AC100-120V~: 3units / AC220-240V~: 6units 6. DMX-512 connection with DMX terminator For installations where the DMX cable has to run a long distance or is in an electrically noisy environment, such as in a discotheque, it is recommended to use a DMX terminator. -
Page 13: Control Board
8. Control Board The Control Board offers several features: you can simply set the starting address , run the pre-programmed program or make a reset. The main menu is accessed by pressing the -button until the display starts flashing. Browse through the menu by pressing the -button , -button , -button or... - Page 14 Address ON/OFF Add. via DMX Close/Hold/Auto/Music Auto run if no DMX No DMX Status ON/OFF Pan Reverse movement Pan Invert ON/OFF Tilt Reverse movement Tilt Invert Status Settings 630/540 Pan Degree Select Pan Degree ON/OFF Movement Feedback Feedback Speed 1~ 4 Movement Mode Select Movement Speed 0~99%...
-
Page 15: Function
Program 1 Program Test Testing program Edit Program Step 01=SCxxx Program in loop Program 10 Step 64=SCxxx Save and exit Pan,Tilt,…… Save and automatically Edit Scene 001 --Fade Time-- Edit Scenes return ~ Edit Scene 250 --Secne Time-- manual scenes edit Input By Exterior Rec. -
Page 16: Information
1．Access the main menu. 2．Tap the <Up/Down>button until“Sound Control”is displayed. 3．Press <ENTER>, the display will show “Sound Control”. 4．Tap the <Up/Down>button，the display will show “Master”, ” Alone”. 5．Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu. 8.1.6 Accelerometer 1．Access the main menu. - Page 17 2．Press <Up/Down>, the display will show “Last Run Time”. 3．Press< ENTER>, the display will show “Last Run Time”. 4．The display will show “XXXX” (Hours) ； 5．Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu. Lamp Hours With this function, you can display the running time of the lamp.
-
Page 18: Temperature Info
2．Press <Up/Down>, the display will show “Clean Last Run”. press< ENTER>, the display will show 3． “Timer Password”menu input a correct password, “ ”, Clean Last Run 4．The display will show “OFF”or“ON”. 5．Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu. Lamp Time Password With this function, you can display the timer password. -
Page 19: Software Version
4．The display will show “Ethernet IP”or“XXX. XXX. XXX. XXX”. 5．Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu. 8.2.4 Software version With this function, you can display the software version of the device. 1．Tap <MODE/ESC>button，access the main menu，Tap the <Up/Down>button until “Information”is displayed. -
Page 20: Lamp On Via External Controller
8.3.3 Lamp on via external controller With this function you can select if you can switch the lamp on via an external controller (DMX-channel of internal programs, value 64-79). Select “ON” by turning the encoder if you wish to enable this function or “OFF” if you don’t. 1．Tap <MODE/ESC>button，access the main menu，Tap the <Up/Down>button until “Lamp Control”is displayed. -
Page 21: Personality
8.4 PERSONALITY 8.4.1 Status settings Address via DMX With this function, you can adjust the desired DMX-address via an external controller. 1．Tap <MODE/ESC>button，access the main menu，Tap the <Up/Down>button until “Personality”is displayed. Press ENTER, the display will show “Personality”. Tap the <Up/Down>button until the display will show “Status setting” . Press ENTER, the display will show “Status setting”. - Page 22 5．Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu. Pan Degree With this function, you can select pan degree for 630 or 540. 1．Tap <MODE/ESC>button，access the main menu，Tap the <Up/Down>button until “Personality”is displayed. Press ENTER, the display will show “Personality”. Tap the <Up/Down>button until the display will show “Status setting”.
-
Page 23: Service Setting
Hibernation ——Standby mode The lamp and step motors will be power off if the fixture stay without DMX signal for 15 mins (Factory default).And the fixture will be reset before working once it receive DMX signal again. 1．Tap <MODE/ESC>button，access the main menu，Tap the <Up/Down>button until “Personality”is displayed. -
Page 24: Display Settings
3．Press< ENTER>, the display will show “Ether Mask IP”. 4．The display show “XXX. XXX. XXX. XXX”. 5．Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu. 8.4.3 Display settings Shutoff time With this function you can shut off the color LCD display after 2 to 59 minutes. Turn the encoder in order to select the desired shut off time. -
Page 25: Select Signal
3．Press< ENTER>, the display will show “Initial status”. 4．The display show “XXX”. 5．Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu. 8.4.6 Select Signal 1．Tap <MODE/ESC>button，access the main menu，Tap the <Up/Down>button until “Personality”is displayed. Press ENTER, the display will show “Personality”. 2．Press <Up/Down>, the display will show “Select Signal”. -
Page 26: Manual Control
5．Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu. 8.6.2 Manual control With this function, you can adjust the lamp more easily. All effects will be canceled, the shutter opens and the dimmer intensity will be set to 100 %. With the individual functions, you can focus the light on a flat surface (wall) and erform the fine lamp adjustment. -
Page 27: Rec. Controller
8.8.4 Rec. Controller The moving head features an integrated DMX-recorder by which you can transmit the programmed scenes from your DMX-controller to the moving head. Adjust the desired scene numbers via the encoder (from – to). When you call up the scenes at your controller, they will automatically be transmitted to the moving head. -
Page 28: Instructions On Use
• Press the Enter button to confirm. • Select “Edit program” by turning the encoder. • Press the Enter button to confirm. • Turn the encoder to select the desired program. With this function you can edit specific scenes into a specific program. - Page 29 47-58 Color 4 59-70 Color 5 71-82 Color 6 83-94 Color 7 95-106 Color 8 107-118 Color 9 119-127 Color 10 128-189 Forwards rainbow effect from fast to slow 190-193 No rotation 194-255 Backwards rainbow effect from slow to fast Color Wheel Fine : 0-255 Color Wheel colour change to any position Fine...
- Page 30 Rotating prism, Prism / Gobo macros: 0-63 Open 64-127 8-Facet Prism 128-135 Macro 1 136-143 Macro 2 144-151 Macro 3 152-159 Macro 4 160-167 Macro 5 168-175 Macro 6 176-183 Macro 7 184-191 Macro 8 192-199 Macro 9 200-207 Macro 10 208-215 Macro 11 216-223...
-
Page 31: Error Message
96-127 No function (shutter open) 128-159 Pulse-effect in sequences 160-191 No function (shutter open) 192-223 Random strobe effect slow to fast 224-255 No function (shutter open) Dimmer intensity: 0-255 Intensity 0 to 100% Fine Dimmer intensity: 0-255 Dimmer intensity fine Frost: 0-127 Disable frost... -
Page 32: Cleaning And Maintenance
performing reset more than 2 times, only the channels which have errors can not work properly, others can work as usual. Please contact with dealer or manufacturer for service, self repair is not allowed. PAN Er (PAN-yoke movement error) This message will appear after the reset of the fixture if the yoke’s magnetic-indexing circuit malfunction (sensor failed or magnet missing) or the stepping-motor is defective (or its driving IC on the main PCB). -
Page 33: Technical Specifications
spots (ceiling, suspension, trussing). 3) Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances. 4) The electric power supply cables must not show any damage, material fatigue or sediments. Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed. - Page 34 XM1093-V1.2.0-NR...
Need help?
Do you have a question about the MegaBeam G10B and is the answer not in the manual?
Questions and answers