1. Manuals
  2. Brands
  3. Triton Blue Manuals
  4. Lighting Equipment
  5. WALLY SC 20
  6. User manual

Triton Blue WALLY SC 20 User Manual

Professional scanner
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
PROFESSIONAL SCANNER USER MANUAL
WALLY SC 20
KEEP THIS MANUAL FOR FUTURE NEEDS

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WALLY SC 20 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Triton Blue WALLY SC 20

Summary of Contents for Triton Blue WALLY SC 20

  • Page 1 PROFESSIONAL SCANNER USER MANUAL WALLY SC 20 KEEP THIS MANUAL FOR FUTURE NEEDS...
  • Page 3 Thank you for your patronage. We are confident that our excellent products and service can satisfy you. For your own safety, please read this user manual carefully before installing the device. In order to install , operate, and maintain the lighting safety and correctly. We suggest that the installation and operation should be done by the verified technician and follow the instruction strictly.

  • Page 4: Safety Instructions

    OVERVIEW 1） Viewfinder 2） Lens 3） Display 4） Mode/Esc-button 5） Up-button 6） Down-button 7） Enter-button 8） Microphone 9） Control board 10） 3-Pin DMX out 11） 3-Pin MDX in 12） Power switch 13） Power input / Fuse 14） Cross screw 15） Join stand Housing 16）...

  • Page 5: General Guidelines

    This device falls under protection-class I. Therefore it is essential that the device be earthed. The electric connection must carry out by qualified person. Make sure that the available voltage is not higher than stated at the end of this manual. Make sure the power cord is never crimped or damaged by sharp edges.

  • Page 6: Installation Instructions

    Operate the device only after having familiarized with its functions. Do not permit operation by persons not qualified for operating the device. Most damages are the result of unprofessional operation. Please use the original packaging if the device is to be transported. For safety reasons, please be aware that all modifications on the device are forbidden.

  • Page 7: Dmx-512 Control Connection

    Before mounting make sure that the installation area can hold a minimum point load of 10 times the device’s weight. Connect the fixture to the mains with the power plug. Installation via the Omega holders Screw one clamp each via a M12 screw and nut directly into the bracket of the scanner. Pull the safety-chain through the bracket of the base and over the trussing system or a safe fixation spot.

  • Page 8: Projector Dmx Start Address Selection

    Projector DMX start address selection All fixtures should be given a DMX starting address when using a DMX signal, so that the correct fixture responds to the correct control signals. This digital starting address is the channel number from which the fixture starts to “listen”...

  • Page 9: Main Functions

    [UP] screen will flash when pressing this key in normal mode, the adress value will increasing. Keep pressing this key, the address value will increase rapidly. it will exit from flash 60 seconds after the last keypress. Press this key under edit mode, you can choose the function you want from the buttom up in the menu. [DOWN] screen will flash when pressing this key in normal mode, the adress value will idecreasing.
  • Page 10 - Main menu 0 Press [MODE/ESC] to enter the main menu "MODE" (display flashing) Press [ENTER] and select "ADDR", “RUN” or "DISP" by pressing [UP] or [DOWN] button. Press [ENTER] for selecting the desired sub menu. - DMX address setting, Slave setting - DMX address setting With this function, you can adjust the desired DMX-address via the Control Board.
  • Page 11 and "MAST" that the device is defined as master. elect "AUTO" or "SOUN" by pressing [UP] or [DOWN] button. Press [ENTER] for selecting the desired extension menu. Select "ALON" or "MAST" by pressing [UP] or [DOWN] button. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu. - Display the DMX-value, Reverse display, Shut off LED display - Display the DMX 512 value of each channel With this function you can display the DMX 512 value of each channel.
  • Page 12 2. Press the [UP] button to select “ON” to activate this function, or “OFF” to deactivate this function. Press [ENTER] to confirm. 3. Press [Mode/Esc] to return to the main menu. Main menu 1 Press [MODE/ESC] to enter the main menu (display flashing). Press [UP] or [DOWN] button.
  • Page 13 - Restore factory settings With this function you can restore the factory settings of the device. All settings will be set back to the default values (shaded). Any edited scenes will be lost. Select “LODA” by pressing [UP] or [DOWN] button. Press [ENTER], the display shows “ON”...
  • Page 14 Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu. - Fixture code and motor fix 1. Select “WHEL” by pressing [UP] or [DOWN] button. 2. Press [ENTER], the display shows “CODE” or “CH01-CHXX”. 4. Select “CODE” or “CH01-CH-XX” by pressing [UP] or [DOWN] button. 5.
  • Page 15 Main menu 4 1. Press [MODE/ESC] to enter the main menu (display flashing). 2. Press [UP] or [DOWN] button to select “EDIT”. - Define the number of steps in Run With this function you can define the number of steps in the Program Run. Select “STEP”...

  • Page 16: Instructions On Use

    b) Editing via the external controller Call up the first scene in your controller now. Select “SC01” by pressing [UP] or [DOWN] button. Press [ENTER], the display shows “SC01”. Press [ENTER], the display shows “C-01”. Select "CNIN" by pressing [UP] or [DOWN] button. Press [ENTER], the display shows "OFF".
  • Page 17 160-175 Rot. gobo 6 (metal) shake 176-191 Rot. gobo 7 (metal) shake 192-255 Rot. gobo wheel cont. rotation slow to fast Rotating gobo index, rotating gobo rotation : 0-127 Gobo indexing 128-189 Forwards gobo rotation from fast to slow 190-193 No rotation 194-255 Backwards gobo rotation from slow to fast Speed Pan/Tilt movement: 0-225...

  • Page 18: Error Message

    ERROR MESSAGE When you turn on the fixture, it will make a reset at first. The display may show“Err channel is XX” while there are problems with one or more channels. “XX” stands for channel 1, 2, 3, 5, 6 who has the testing sensor for positioning.

  • Page 19: Technical Specifications

    solvents. Should you need any spare parts, please order genuine parts from your local dealer. TECHNICAL SPECIFICATIONS Power supply: □ □ □ □ □ □ AC 100V~ 50Hz; AC 120V~ 50Hz; AC 208V~ 50Hz; AC 220V~ 50Hz; AC 230V~ 50Hz; AC 240 V~ 50Hz;...

Table of Contents