Advertisement

Quick Links

MT-5210 3 1/2 LCR Meter
User's Manual
st
,
1
Edition
2011
©2011 Copy Right by Prokit's Industries Co., Ltd.
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MT-5210 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Pro's Kit MT-5210

  • Page 1 MT-5210 3 1/2 LCR Meter User’s Manual Edition 2011 ©2011 Copy Right by Prokit’s Industries Co., Ltd.
  • Page 2: Safety Note

    1. SUMMARIZE The meter is a stable multimeter with 3 2/1 LCD displays , 9V drive by battery. It's widely used on measuring Inductance, resistance, capacitance, diode, transistor rest and continuity buzzer. It’s an ideal tool for lab, factory and family. 2.
  • Page 3: Technical Characteristic

    4. CHARACTERISTIC 1 GENERAL 1-1 Displaying: LCD displaying. 1-2 Max. displaying: 1999 3 1/2 digit auto polarity indication. 1-3 Measuring method: dual slope A/D conversion. 1-4 Sampling rate: approx. 3 times/second. 1-5 Over range indication: the MSD displays“1”. 1-6 Low battery indication:“ ”...
  • Page 4: Measure Frequency

    2-2.CAPACITANCE(C) RANGE ACCURACY RESOLUTION MEASURE FREQUENCY ±(1.0%+5d) About 200Hz 20nF 10pF 200nF 100pF ±(2.0%+5d) 20uF 10nF About 16Hz 200uF ±(5.0%+5d) 100nf 1000uF ±(5.0%+25d) About 8Hz 2-3.RESISTANCE Ω RANGE ACCURACY RESOLUTION 200Ω ±(0.8%+5d) 0.1Ω 2kΩ 1Ω 20kΩ 10Ω ±(0.8%+3d) 200kΩ 100Ω 2MΩ...
  • Page 5 5.2 CONSIDERATION OF MEASUREMENT (1) This LC METER is intended for measuring the capacitance value of a capacitor, the inductance value of an inductor. It is not intended for determining the “Q” factor for above reactive components. Misleading readings may be obtained if the measurement of the inductance or capacitance of a resistor is attempted.
  • Page 6 5.4 CAPACITANCE(C) MEASURING PROCE DURE (1) Press the POWER button to turn the power on (2) Select the range switch for the maximum expected capacitance. (3) Fully discharge any capacitors. (4) Connect the alligator clips to the capacitor leads. (5) Read the display. The value is direct reading in the electric al unit (nF, uF) indicated at the selected range switch.
  • Page 7: Diode And Continuity Test

    5.5 RESISTANCE (Ω) MEASURING PROCEDURE (1) Press the POWER button to turn the power on (2) Select the range switch for the maximum expected resistance. (3) Insert the black test leads into the “COM” jack, and the red one into the “V/Ω/Hz” jack; (4) Turn the range switch to resistance position, and then connect the test leads at the two ends of the resistor.
  • Page 8: Maintenance

    (60±20) Ω. 5.8 DATA HOLD Press HOLD, the peak value of current data will be keep displaying on LCD; press it again to cancel this functio n. 6. MAINTENANCE DO NOT try to verify the circuit for it’s a precision meter. 1.
  • Page 9 MT-5210 3 1/2 3 1/2 LCD IEC1010 36DCV 25ACV “ ” “ ” 2 mH-20H 2nF-1000uF 200O-20MO...
  • Page 10 1-1. 1-2. 1999 (3 1/2 digit) 1-3. A / D 1-4. 1-5. “1” “ ” 1-7. (0 ~40 R.H.<80% 1-8. 9V (NEDA1604/6F22 1-9. 189×97×35mm 1-10. 1-11. ± a × 23 ± 5 <75 2-1. ±(2.0%+5d) 20mH 10 uH About 200mH 100uH 200Hz ±(5.0%+5d)
  • Page 11 2-3. (Ω) 200Ω ±(0.8%+5d) 0.1Ω 2kΩ 1Ω 20kΩ 10Ω ±(0.8%+3d) 200kΩ 100Ω 2MΩ 1kΩ 20 MΩ ±(1.0%+15d) 10 kΩ 1. LCD “Q” “ - ” “+” (uH H) “1”...
  • Page 12 (nF, uF) “1” “COM” “V /Ω/ ” “1”...
  • Page 13 ”1” 1MΩ “hFE” “COM” “Ω” 60 ± 20 Ω HOLD...
  • Page 14 ©2011 Prokit’s Industries Co., LTD. All rights reserved 2011001(T)

Table of Contents