WARNING U-Line Corporation direct. Consult the installation guide before any installation begins. U-Line contact SHOCK HAZARD - Electrical Grounding Required. information appears on the rear cover of this guide. • Never attempt to repair or perform maintenance on •...
For best results use Claire Stainless Steel Polish and ULN-BI95WH-00 Cleaner, which can be purchased from U-Line Corporation (Part numbers 173348). Frequent cleaning will remove surface Please carefully follow the directions that apply to your unit and contamination that could lead to rust.
3 Prepare Site Filler Panel (Not Provided by U-Line) – May Be Added Above or Below Unit Your U-Line product has been designed for either free-standing or to Enclose for a Built-In Look built-in installation. When built-in, your unit does not require additional air space for top, sides or rear.
SS-1095NF Models BCM95 Models Filler Panel (Not Provided by U-Line) – Filler Panel (Not Provided by U-Line) – May Be Added Above or Below Unit Needed to Attach Mounting Flange on Unit to Enclose for a Built-In Look Typical Counter 18-1/2””...
*Add 1-1/2” For For Water Line Clearance BI98 & SS98 3-13/16” 15" *Add 5/8” For Water Line Clearance 15” 14-15/16" 20” * *Add 3/4” To Depth For Water Line Clearance 27-3/8" 8-15/16” *Add 1-1/2” For For Water Line Clearance u-line.com...
8 15/16" *Add 1-1/2" For Water Line Clearance *Add 1-1/2" For For Water Line Clearance SS1095NF WH95TP 17" * 14" 14" 17"* 25-1/16" 25-1/8" 9" 8 15/16" *Add 1-1/2" For For Water Line Clearance *Add 1-1/2" For Water Line Clearance u-line.com...
Door Swing Dimensions 5 Other Site Requirements All units have a zero clearance for the door to open 90°. U-Line recommends a minimum door clearance of 2" to accommodate Power Supply the handle if the unit is installed next to a wall or similar type of structure.
Align hinge outer edge with cabinet before tightening screws. 5. Relocate plastic spacer/ bushing on bottom of door to opposite side, and place door on bottom hinge pin. See Figure 5. Clean out bushing hole in door bottom with a screwdriver if necessary. u-line.com...
13. Gently slide travel pin assembly through flange and then fasten to unit. Make sure travel pin in door engages the closer in the assembly, then tighten screws on travel pin assembly securely. u-line.com...
Be sure to tighten all four screws removed in Step 7. 6. Install hinge on opposite side, bottom of cabinet (Figure 23). Align hinge outer edge with cabinet before tightening screws. 12. Remove pivot screw from top hinge, invert screw and reinstall pivot screw in top hinge (Figure 27). u-line.com...
Page 13
Fasten upper hinge to unit (three screws (Figure 30). Partially tighten screws. 16. Adjust door to assure proper seal. Tighten upper and lower hinge screws securely. 17. Replace screws in holes in bottom of unit on opposite side. 18. Replace the grille. u-line.com...
Remove door by tilting forward and lifting off bottom hinge pin. 2. Pull door gasket out of groove (top edge of door only). Start in the middle and pull outward, moving toward the edge. This may take some force. BI-95 BI-2115 BI95BTP u-line.com...
2. Align door squarely with cabinet. Make sure gasket is firmly in 24" 21-1/2" Minimum contact with cabinet all the way around the door (no gaps). 7" 7" 3. Tighten bottom hinge screws. 4" 1" 4. Tighten top hinge screws. u-line.com...
Rear Mount Front Mount NOTICE U-Line requires the use of copper tubing for installation. Do not use any plastic water supply line. The line is under pressure at all times. Plastic may crack or rupture with age and cause water damage to your home.
Level should be placed along top edge and side edge as shown. Insert This Lip Behind Base Plate Lip Align the grille and cabinet screw holes. Insert the grille screw and tighten. Do not over-tighten. u-line.com...
Problem The custom overlay door was designed to align with the rest of the cabinet doors, but the unit has crept forward. Solution Make sure that the electrical cord and water supply line are not obstructing the installation. u-line.com...
Page 19
E-mail: onlineparts@u-line.com BUILDING ON THREE GENERATIONS OF INNOVATION For over five decades and through three generations, U-Line continues to be the leader in innovation, quality and performance in the premium built-in undercounter ice making, refrigeration and wine preservation market. U-Line has captivated those with an appreciation for the finer things with exceptional functionality, style, inspired innovation and attention to even the smallest details.