1. Manuals
  2. Brands
  3. Gage Bilt Manuals
  4. Tools
  5. GB704SR-8
  6. Installation manual

Gage Bilt GB704SR-8 Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
S/N: 1088 AND ABOVE
GB704SR-8
PLEASE CONTACT GAGE BILT FOR
ALL OTHER SERIAL NUMBERS.
INSTALLATION TOOL
GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE
E-MAIL US FOR A DISTRIBUTOR NEAR YOU.
GAGE BILT Inc.
GAGE BILT
44766 Centre Court
(586) 226-1500
Clinton Twp. MI 48038
(586) 226-1505 Fax
MADE IN U.S.A.
e-mail: solutions@gagebilt.com / www.gagebilt.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GB704SR-8 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Gage Bilt GB704SR-8

Summary of Contents for Gage Bilt GB704SR-8

  • Page 1 S/N: 1088 AND ABOVE GB704SR-8 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT Inc. GAGE BILT 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586) 226-1505 Fax MADE IN U.S.A.

  • Page 2: Table Of Contents

    - .600" (15.24 mm) Rated pull load - 3,300 lbs. (14.68 kN) Noise level - 81.5 dB (A) Vibration - Tested– No hazards found. S/N: 1088 AND ABOVE 11/11 Rev. 9/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 3: Warnings

    73.2 dB (A). In this daily basis for damage or wear. Any repair should condition the max level was 81.5 dB (A). Therefore, be done by qualified personnel trained on Gage Bilt it is required where prolonged use, hearing procedures.

  • Page 4: Principle Of Operation

    CYLINDER HEAD HEAD PISTON PRESSURE PRESSURE PRESSURE PISTON PISTON PRESSURE PRESSURE VALVE SPOOL PISTON PRESSURE PRESSURE PRESSURE EXHAUST Image may not reflect actual tool S/N: 1088 AND ABOVE 11/11 Rev. 9/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 5: How To Use The Gb704Sr-8

    Always disconnect air supply when tool is not in use to prevent accidental start-up. NOSE HEAD ASSEMBLY CYLINDER ASSY DEFLECTOR RIVET WORK ACTUATOR SHIPPING ASSY PLUG QUICK DISCONNECT Image may not reflect actual tool FITTING S/N: 1088 AND ABOVE 11/11 Rev. 9/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 6: Description, Maintenance And Hydraulic Thread Preparation

    The GB704SR-8 split handle riveter operates with 90 to 100 psi (6.2-6.9 bar). providing maximum efficiency. At 90 psi. (6.2 bar) air pressure, the GB704SR-8 does not exceed 81.5 dB (A) and consumes 3 cfm at 20 cycles per minute.

  • Page 7: Filling And Bleeding

    (B). If stroke is not consistent within 1/64" (.0156”) repeat bleeding steps 5-6. Re-attach lever assy (724017) to manifold-head assy (744306). .740 (18.8mm) .140 (3.6mm) S/N: 1088 AND ABOVE 11/11 Rev. 9/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 8: Troubleshooting

    Replace worn or broken parts. Clean the surface the jaws ride on. Stems lodged side by side in the follower. Disassemble, remove stems, and reassemble. Incorrect follower. S/N: 1088 AND ABOVE 11/11 Rev. 9/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 9: Overhaul, Disassembly And Parts Lists

    WARNING: Tool must be maintained in a safe working condition at all times and examined on a regular daily basis for damage or wear. Any repair should be done by qualified personnel trained on Gage Bilt procedures. WARNING: When operating, repairing or overhauling tool, wear approved eye protection. Do not look in Front of tool or rear of tool when installing fastener.
  • Page 10 400061 744303 - MANIFOLD-HANDLE SOCKET HEAD SOCKET HEAD CAP SCREW (2) CAP SCREW (2) S572 - STAT-O-SEAL (2) 402482 BUTTON HEAD CAP SCREW (2) S/N: 1088 AND ABOVE 11/11 Rev. 9/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
  • Page 11 744142 - VALVE PLUG 744124 - BASE COVER 400785 - O'RING 744136 PISTON ROD ASSEMBLY 744143 - MUFFLER (INCLUDES S908 AND A-201) 744149 - PIN S/N: 1088 AND ABOVE 11/11 Rev. 9/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 12: Dexron® Iii Oil Safety Data

    Use material for its intended purpose or recycle if possible. Oil collection services are available for used oil recycling or disposal. Place contaminated materials in containers and dispose of in a manner consistent with applicable regulations S/N: 1088 AND ABOVE 11/11 Rev. 9/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 13: Nose Assembly Selection Chart

    GS8-715-40OS (1) BACS53B1EA1/2 CHERRYMAX® and MBC® are registered trademarks of Cherry Aerospace Fasteners. GAGE BILT CERTIFIES THE GB704 WILL INSTALL THE ABOVE FASTENERS 1) 715 SERIES NOSE ASSEMBLIES REQUIRE 704001 ADAPTER. 2) INSTALLS 1/8", 5/32", AND 3/16" DIAMETERS 3) RIGHT ANGLE NOSE ASSEMBLIES MAY REQUIRE MORE THAN ONE PULL 4) FRONT END EJECTING NOSE ASSEMBLY.

  • Page 14: Eu Conformity And Warranty

    GAGE BILT DECLARATION OF CONFORMITY MANUFACTURER: Gage Bilt Inc. 44766 Centre Ct. Clinton Twp. Michigan (586-226-1500) WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS TO THE FOLLOWING DIRECTIVES AND STANDARDS Machinery Directive 2006/42/EC EN12100-1 & EN12100-2 EN792-1:2000+A1 EU REPRESENTATIVE Edgar Hausmann GmbH Förster-Busch-Str. 10 D-34346 Hann. Münden Germany EQUIPMENT DESCRIPTION: GB704SR-8 FASTENER INSTALLATION TOOL This procuct specified above conforms to the above dIrectives and standards.

Table of Contents